3060 electro-mechanical programmer for controlling heating & hot water Installation & User Instructions This product complies with the following EC Directives: Electro-Magnetic Compatibility Directive. (EMC) (2004/108/EC) Low Voltage Directive.
Index Installation Product specification 3 Installation 4 Wiring 4-5 User Your programmer Programming the unit Setting the clock Using the programmer INDEX Contact details 2 6 6-7 7 8-9 12
Installation Instructions Please Note: This product should only be installed by a qualified electrician or competent heating installer, and should be in accordance with the current edition of the IEEE wiring regulations. Product specification Power supply 230 ± 15% Vac, 50/60Hz Switch action 2 x SPST, type 1B Switch rating Max 264 Vac, 50/60Hz, 3(1) A Timing accuracy ± 1 min/month Enclosure rating IP30 Max.
1. Remove lower setting dial. Set all four tappets to top of upper dial. Unscrew 4BA screw and remove outer case. 2. Slacken two screws securing plug-in module to backplate and separate module from backplate by pulling upwards. 3. Fix backplate to wall (3 hole fixing). 4. Referring to wiring diagrams below and opposite make electrical connections as shown (as applicable).
Wiring WIRING - FULLY PUMPED SYSTEM 1 2 5 4 3 6 7 6 7 3060 Terminals Mains N Supply L WIRING - FULLY PUMPED SYSTEM 1 2 Danfoss Randall RMT230 Room Stat 5 4 3 (N) 2 2 3 core Danfoss Randall RMT230 Room Stat 1 4 2 Flying lead 1 2 3 4 2 core 5 6 4 5 3 7 S/L Brown Orange Grey Blue 3 6 2 core + 3 core Danfoss Randall ATC Cylinder Stat 1 (N) 13 core 2 Brown Grey Orange Blue 3 2 core 2 3060 Terminals Mains N Supply L Danfoss Randall ATC Cylinder Stat 1 1 4 7 S/L 8 8
User Instructions Your programmer Your Programmer & Programming the unit The 3060 programmer allows you to switch your hot water and heating on and off at times that suit you. 6 Four tappets on the timing dial let you decide when you want your hot water and heating to come on and go off each day. The programmer provides 2 ON times and 2 OFF times per day.
2 Still holding the central knob, move the blue tappet marked ‘B’ to the time you want your HEATING/HOT WATER to switch off in the morning. 3 You can set your other two tappets in the same way to set your HEATING/HOT WATER for the afternoon or evening. EXAMPLE (NB.
Using the Programmer The selector switch is used to select how the 3060 controls your hot water and heating. The heating and hot water can be operated together in various combinations, or the water can be controlled on its own (i.e. during the summer when only hot water is required). Using the programmer H+W ON H - ONCE W - ONCE H - TWICE W - ONCE H - TWICE W - TWICE H - OFF W - TWICE H+W OFF There are six positions into which the selector switch may be set.
4 - H ON / W ON This is the ‘CONSTANT’ position and the programmer will remain permanently ON for both Heating and Hot Water, irrespective of the position of the tappets. 6 - H OFF / W TWICE In this position the Heating will be permanently OFF and the Hot Water will come on and go off according to the times you have programmed (ON at A, OFF at B, ON at C, OFF at D). Note: If hot water is required all day with the heating shut off (i.e.
Still having problems? Call your local heating engineer: Name: Tel: Visit our website: www.heating.danfoss.co.uk Email our technical department: ukheating.technical@danfoss.com Call our technical department 0845 121 7505 (8.45-5.00 Mon-Thurs, 8.45-4.30 Fri) For a large print version of these instructions please contact the Marketing Services Department on 0845 121 7400. Danfoss Ltd Ampthill Road Bedford MK42 9ER Tel: 01234 364621 Fax: 01234 219705 Part No.
