Install Instructions

Troubleshooting
E02 - This error message indicates a missing or damaged floor sensor.
Contact your installer to verify the floor sensor and connections.
Classification
The product is a Class II device (reinforced insulation) and must be con-
nected to the following leads:
Phase L1 (L) 120 V
Neutral L2 (N) 0/120 V
Max. load 15 A (resistive load) The thermostat is intended to be used with
underfloor heating.
The terminals are suitable for field wiring cables of 12 to 20 AWG.
Technical data
Supply . ...............................................................................120/240 Vac
Load ............................................................max. 15 A (resistive load)
Power .................................................................... 1.800 W at 120 Vac
.................................................................... 3.120 W at 208 Vac
.................................................................... 3.600 W at 240 Vac
GFCI (UTN4) .................................................Class A (5 mA trip level))
Floor sensor .............................................................NTC 10K Ω @ 25°C
UL Listed for the US and Canada
According to the following standards:
Thermostat: UL 60730-1
UL 60730-2-9
CSA E60730-1
CSA E60730-2-9
UL file number: E157297
UTN4 / GFCI: UL 943 fourth ed.
CSA C22.2 No. 144.1-06
Patent pending
Dépannage
E02 - Ce message d’erreur indique un capteur de plancher manquant ou
endommagé. Communiquer avec l’installateur pour vérifier le capteur de
plancher et les connexions.
Classification
Ce produit est un appareil classé II (isolation renforcée) et doit être bran-
ché aux fils suivants :
Phase L1 (L) 120 V
Neutre L2 (N) 0/120 V
Charge maximum 15 A (charge résistive) Le thermostat est conçu pour
être utilisé avec des planchers chauants.
Les borniers sont adéquats pour du câble de construction de 12 à
20 AWG.
Caractéristiques techniques
Alimentation .......................................................................120/240 VCA
Charge ....................................................... Max. 15 A (charge résistive)
Puissance ................................................................ 1800 W à 120 VCA
..................................................................... 3120 W à 208 VCA
..................................................................... 3600 W à 240 VCA
DDFT (UTN4) ....................... Class A (5 mA, niveau de déclenchement)
Sonde de plancher ................................................. NTC 10K Ω @ 25 °C
c-UL-us
Selon les normes suivantes :
DISJONCTEUR DE FUITE À LA TERRE
Thermostat: UL 60730-1
UL 60730-2-9
CSA E60730-1
CSA E60730-2-9
Numéro de dossier UL E157297
UTN4 / DDFT: UL 943 quatrième éd.
CSA C22.2 No. 144.1-06
En instance de brevet.
BASIC OPERATION
Increasing/Decreasing the Temperature
By default, the thermostat displays the CURRENT temperature.
Press the Up/Down buttons ONCE to activate the backlight. Press
the Up/Down buttons again to adjust the TARGET temperature be-
tween 41 to 104° F (0 to 40°C). The screen will display the TARGET
temperature for five seconds.
Setting the Time
1. Press the Center button TWICE to access the Menu.
2. Using the Up/Down buttons, go to 12/24 and press the Center
button.
3. Select the time format (12-hour clock or 24-hour clock) and press
the Center button.
4. Using the Up/Down buttons, go to TIME and press the Center
button.
5. Set the hour and press the Center button.
6. Set the minutes and press the Center button.
7. Using the Up/Down buttons, go to EXIT and press the Center
button.
Changing the Temperature Unit
1. Press the Center button TWICE to access the Menu.
2. Using the Up/Down buttons, go to C/F and press the Center
button.
3. Select the temperature unit (Celsius or Fahrenheit) and press the
Center button.
4. Using the Up/Down buttons, go to EXIT and press the Center
button.
Changing the Temperature Control Setting
1. Press the Center button TWICE to access the Menu.
2. Using the Up/Down buttons, go to FLOOR/ROOM and press the
Center button.
3. Select the temperature control setting and press the Center but-
ton.
4. Using the Up/Down buttons, go to EXIT and press the Center
button.
OPÉRATION DE BASE
Augmenter/Réduire la température
Par défaut, le thermostat ache la température ACTUELLE. Ap-
puyer sur les boutons Up/Down UNE FOIS pour allumer le panneau
lumineux. Appuyez à nouveau sur les boutons Up/Down pour régler
la température CIBLE entre 41 et 104 °F (0 et 40 °C). L’écran af-
fichera la température CIBLE pendant 5 secondes.
Régler l’heure
1. Appuyer sur le bouton centre DEUX FOIS pour accéder au menu.
2. À l’aide des boutons Up/Down, aller à 12/24 et appuyer sur le
bouton centre.
3. Sélectionner l’achage de l’heure (format horaire 12 ou 24 heu-
res), puis appuyer sur le bouton centre.
4. À l’aide des boutons Up/Down, aller à HEURE et appuyer sur le
bouton centre.
5. Sélectionner l’heure et appuyer sur le bouton centre.
6. Sélectionner les minutes et appuyer sur le bouton centre.
7. À l’aide des boutons Up/Down, aller à QUITTER et appuyer sur le
bouton centre.
Changer l’unité de température
1. Appuyer sur le bouton centre DEUX FOIS pour accéder au menu.
2. À l’aide des boutons Up/Down, aller à C/F et appuyer sur le
bouton centre.
3. Sélectionner l’unité de température (Celcius ou Fahrenheit) et ap-
puyer sur le bouton centre.
4. À l’aide des boutons Up/Down, aller à QUITTER et appuyer sur le
bouton centre.
Changer les réglages de température
1. Appuyer sur le bouton centre DEUX FOIS pour accéder au menu.
2. À l’aide des boutons Up/Down, aller à C/F et appuyer sur le
bouton centre.
3. Sélectionner l’unité de température (Celcius ou Fahrenheit) et ap-
puyer sur le bouton centre.
4. À l’aide des boutons Up/Down, aller à QUITTER et appuyer sur le
bouton centre.
Réglage de la
température
Description
Floor
(par défaut)
La sonde de plancher contrôle le chauage.
La protection du plancher est activée. Les limites
sont comme pour plancher/pièce.
Room La sonde intégrée contrôle le chauage.
Ce réglage est utile si la sonde de température
du plancher est endommagée ou s’il n’y en a pas
d’installée. La protection du plancher N’EST PAS
activée.
Floor/Room La sonde intégrée contrôle le chauage et la sonde
de plancher limite la température du plancher à
104 °F/40 °C pour des tuiles ou 82 °F/28 °C pour du
stratifié.
67547A 02/16 (ALA)
WARNINGS:
To avoid electric shock, disconnect the heating system power supply
at the main panel before installation and maintenance of the thermo-
stat. Keep thermostat air vents clean and free from obstruction. This
thermostat is an electrical device and must be installed in compli
-
ance with national and/or local electrical codes. Installation must be
performed by qualified personnel where required by law.
If a power module with an equipment ground fault protection device
(EGFPD) is to be installed where national and/or local electrical codes
require a ground fault circuit interrupter (GFCI), a separate GFCI must
also be installed.
AVERTISSEMENTS :
Pour éviter l’électrocution, coupez l’alimentation du système de chauf-
fage au panneau principal avant de faire l’installation et/ou l’entretien
du thermostat. Maintenez les évents du thermostat propres et libres
d’obstruction. Ce thermostat est un appareil électrique et doit être
installé conformément aux codes électriques nationaux et/ou locaux.
L’installation doit être eectuée par du personnel qualifié quand la loi
l’exige.
Si un module de puissance possédant un circuit de protection contre
les fuites à la terre (EGFPD) doit être installé où les codes électriques
nationaux et/ou locaux requièrent un disjoncteur de fuite à la terre
(DDFT), un DDFT séparé doit aussi être installé.
For support please contact your installer or retailer.
Pour le soutien, communiquez avec votre installateur ou votre
détaillant.
Danfoss
11655 Crossroads Circle
Baltimore, MD 21220
1.866.676.8062
© 2016 OJ Electronics. All rights reserved.
This manual and parts thereof are protected under Danish and
international copyright laws.
© 2016 OJ Electronics. Tous droits réservés.
Ce manuel et son contenu sont protégés par les lois internationales et
danoises sur les droits d’auteur.
Danfoss
Non-Programmable
Thermostat
QUICK GUIDE
GUIDE RAPIDE
Spare this document.
Piezas de este documento.
Changing the Floor Type (not selectable if the Temperature Control
setting is set to ROOM – refer to ‘Changing Temperature Control Set-
ting’ section). Laminate is the default floor type.
1. Press the Center button TWICE to access the Menu.
2. Using the Up/Down buttons, go to TILE/LAMINATE and press the
Center button.
A. TILE - the floor temperature will be limited to 104°F/40°C
B. LAMINATE - the floor temperature will be limited to 82°F/28°C.
3. Select the floor type and press the Center button.
4. Using the Up/Down buttons, go to EXIT and press the Center but-
ton.
Monitoring Usage
1. Press the Center button TWICE to access the Menu.
2. Using the Up/Down buttons, go to HISTORY and press the Center
button.
A. The display will show the number of HOURS (denoted by the ’h’
on the right side of the screen) the floor heating system has been
heating over the past 7 days. When done, press the Center button.
3. Using the Up/Down buttons, go to EXIT and press the Center but-
ton.
Temperature
Control Setting
Description
Floor (Default) The floor sensor controls the heating.
Floor protection is active. Limits as in Floor/Room.
Room The built-in sensor controls the heating.
This setting is useful if the temperature sensor in
the floor is damaged or none is installed.
Floor protection is NOT active.
Floor/Room The built-in sensor controls the heating and
the floor sensor limits the floor temperature to
104°F/40°C for Tile or 82°F/28°C for Laminate.
Changer le type de plancher (seulement possible si ROOM est
sélectionné – se reporter à la section Changer les réglages de
température) Le stratifié est le type de plancher par défaut.
1. Appuyer sur le bouton centre DEUX FOIS pour accéder au menu.
2. À l’aide des boutons Up/Down, aller à CARRELAGE/LAMINÉ et ap-
puyer sur le bouton centre.
A. CARRELAGE – la température du plancher sera limitée à 104
°F/40 °C
B. LAMINÉ – la température du plancher sera limitée à 82 °F/28 °C
3. Sélectionner le type de plancher et appuyer sur le bouton centre.
4. À l’aide des boutons Up/Down, aller à QUITTER et appuyer sur le
bouton centre.
Contrôler l’utilisation
1. Appuyer sur le bouton centre DEUX FOIS pour accéder au menu.
2. À l’aide des boutons Up/Down, aller à HISTORIQUE et appuyer sur
le bouton centre.
A. L’écran achera le nombre d’HEURES (noté par le “h” à la droite
de l’écran) de fonctionnement du chauage pendant les 7 derniers
jours. Quand c’est terminé, appuyez sur le bouton du centre.
3. À l’aide des boutons Up/Down, aller à QUITTER et appuyer sur le
bouton centre.
© 2016 OJ Electronics A/S
http://danfoss.ipapercms.dk/Heating/
AutoGen/43300_51044/?Purge=true

Summary of content (2 pages)