Instructions / Assembly

ManualsBrandsDanco ManualsBathtub Spouts10317

UNIVERSAL

TUB SPOUT W/ HIDDEN DIVERTER

2" - 3"

1/2" COPPER

STUB OUT NIPPLE

1/2" IPS THREAD

LONG STUB OUT

NIPPLE

1/2" - 3/4"

1/2" IPS THREAD

STUB OUT NIPPLE

1/2" - 3/4"

3/4" IPS THREAD

STUB OUT NIPPLE

Note: This device is designed in compliance with ASME A112.18.1-2005/CSA B125.1-05 standards. A small amount of water is intended

to flow from the spout when the diverter is engaged.This is a safety feature to help prevent unintended release of water.

Fig. A. 1/2˝ Copper Pipe Slip Connection

Tools Required: Phillips Screwdriver, Pipe Thread Tape, Silicon Grease

a) Measure Stub Out Nipple length from wall surface to end of pipe. To use this connection method, Stub Out Nipple must be between 2” and 3” long (Fig. 1).

b) End of Stub Out Nipple should be even. Use sandpaper to remove burrs and sharp edges from end of tubing and to polish tube surface to a smooth, bright copper color.

c) Slide Adapter (A) onto Stub Out Nipple, with the threads facing the wall (Fig. 2). Lubricate Stub Out Nipple about 1” from the end with silicone grease.

d) Slide O-ring (B) onto Stub Out Nipple at least 1/2” from end of nipple.

e) Slide Extension Nipple (C) onto Stub Out Nipple and thread onto Adapter (A), aligning hole in Extension Nipple (C) with slot in Adapter (A). Turning clockwise, tighten

Extension Nipple (C) onto Adapter (A) until slot in Adapter (A) again aligns with hole in Extension Nipple (C).

f) Thread Screw (E) into Retainer Ring (D). Slide Retainer Ring (D) and Screw (E) assembly onto Extension Nipple (C) and align Screw (E) with recessed hole on Extension

Nipple (C). Tighten Screw (E) forcing it to just push through Extension Nipple (C) (Fig. 3).

g) Using a Phillips screwdriver, tighten Screw (E) until it touches Stub Out Nipple (Fig. 3). Note: Do Not Tighten. Tighten Extension Nipple (C) on to Adapter (A) until it touches

Screw (G) and will not turn any more. Slide assembly on Stub Out Nipple until the back of the Extension Nipple (C) is even with the wall surface. Note: Screw (E) may be

loosened slightly to allow Extension Nipple (C) to move freely.

h) Use a Phillips screwdriver to tighten Screw (E) until it touches Stub Out Nipple, then tighten 1/2 to 1 full turn to secure Extension Nipple (C) to Stub Out Nipple. CAUTION: DO

NOT OVERTIGHTEN. THIS WILL CAUSE PERMANENT DAMAGE.

i) Wrapping clockwise, apply 2 to 4 turns of Pipe Thread Tape to the threads on male end of Extension Nipple (C). (Fig. 4)

j) Turning clockwise, tighten new Spout (F) onto the Extension Nipple (C)(Fig. 4).

k) TEST FOR LEAKS. CAUTION: DO NOT USE IF LEAKING FROM REAR. WALL DAMAGE COULD OCCUR.

To Operate Diverter (Used to direct water to the showerhead)

While water is running, gently lift up on diverter knob (Fig. 5). Water will be re-directed to the showerhead. Once the water is turned off, diverter will return to the original position.

A. B. C. D.

APPLY THREAD

TAPE

Fig. 4

Fig. 3

1/2" COPPER

STUB OUT

Fig. 2

Fig. 1

2" - 3"

1/2" COPPER

STUB OUT NIPPLE

SPOUT OPENING

Fig. 5

Instructions:

Remove old tub spout. Determine connection by comparing yours to the images below.

10315 / 10316 / 10317

Page 1 of 3

Summary of content (6 pages)

PAGE 1
UNIVERSAL TUB SPOUT W/ HIDDEN DIVERTER Note: This device is designed in compliance with ASME A112.18.1-2005/CSA B125.1-05 standards. A small amount of water is intended to flow from the spout when the diverter is engaged.This is a safety feature to help prevent unintended release of water. Instructions: Remove old tub spout. Determine connection by comparing yours to the images below. A. B. 1/2" COPPER STUB OUT NIPPLE 2" - 3" 1/2" IPS THREAD STUB OUT NIPPLE 1/2" - 3/4" C. D.
PAGE 2
Fig. B. 1/2˝ Male Threaded Connection with Short Stub Out Connection Tools Required: Pipe Thread Tape a) Measure Stub Out Nipple length from wall surface to end of threads. To use this connection method, Stub Out Nipple must extend between 1/2” and 3/4” beyond wall surface b) Wrapping clockwise, apply 2 to 4 turns of Pipe Thread Tape to the threads of Stub Out Nipple (Fig. 2). c) Turning clockwise, thread Reducer Adapter (G) onto Stub Out Nipple.
PAGE 3
Fig. D. 3/4˝ Male Threaded Connection with Short Stub Out Nipple Tools Required: Pipe Thread Tape a) Measure Stub Out Nipple length from wall surface to end of threads. Stub Out Nipple must be between 1/2” and 3/4” long (Fig. 1). b) Turning clockwise, wrap 2 to 4 turns of Pipe Thread Tape onto threaded end of Stub Out (Fig. 2). c) Turning clockwise, Hand Tighten Extension Nipple (C) onto ¾” Stub Out Nipple until the back of Extension Nipple (C) is even with wall surface (Fig. 2).
PAGE 4
PICO DE BAÑERA CON DESVIADOR OCULTO Note: Este aparato ha sido concebido en conformidad con los estándares ASME A112.18.1-2005/CSA B125.1-05. Una cantidad pequeña de agua fluye del pico cuando el desviador es activado. Esto es una medida de seguridad para prevenir liberación no deseada de agua. Instrucciones: Remueva el pico existente de la bañera. Determine la conexión. A. B. 2" - 3" BOQUILLA DE COBRE DE ½ PULGADA PARA PICO (DE BAÑERA) C. D.
PAGE 5
Figura B. Para la conexión roscada macho de ½ pulgada con conexión de pico de bañera corto Herramientas necesarias: Cinta para roscas de tubo a) Mida la longitud de la boquilla del pico desde la superficie de la pared hasta la extremidad de las roscas. Para utilizar este método de conexión, la boquilla del pico se debe extender entre ½ y ¾ pulgada más allá de la superficie de la pared (Figura 1).
PAGE 6
Figura D. Para la conexión roscada macho de ¾ pulgada con boquilla corta de pico Herramientas necesarias: Cinta para roscas de tubo a) Mida la longitud de la boquilla del pico desde la superficie de la pared hasta la extremidad de las roscas. La boquilla del pico debe medir entre ½ y ¾ pulgada de longitud (Figura 1). b) c) En el sentido de la agujas del reloj, aplique cinta para roscas de tubo dando entre 2 y 4 vueltas alrededor de las roscas en la extremidad del pico (Figura 2).