Danalock V3 US www.danalock.
Table of content 0. Parts involved 1. Download the Danalock app 2. Get your tools together 3. Check door alignment 4. Secure outside keyhole 5. Remove inside thumb-turn 6. Select a backplate 7. Remove the paper from the stickers 8. Fasten backplate 9. Select tailpiece adapter 10. Insert adapter into Danalock 11. Fit and fasten Danalock 12. Align the platemarks 13. Fasten the Danalock 14. Activate batteries 15. Before completing the setup 16. Open the Danalock app 17.
0.
1. Download the Danalock app Go to Google Play or App Store and download the Danalock app. When the app is installed you create a user profile by pressing the blue ring. You will use this profile each time you sign into the app. You will need to finish setting the Danalock up in the app after mounting it on the door.
2. Get your tools together To install the Danalock, you’ll need a Phillips screwdriver and tape, preferably masking tape. Should you need to remove or readjust the lock, a pen tip or paper clip will be needed.
3. Check door alignment Ensure that your door is properly aligned before beginning installation. You should be able to lock your door without pushing, pulling, or lifting the door. Thumb-turn must move and lock smoothly.
4. Secure outside keyhole Before removing your existing lock, use tape to secure the outside keyhole. This will keep it in place as you remove the screws on the inside.
5. Remove inside thumb-turn Remove the inside thumb-turn, leaving just the deadbolt and tail piece remaining. Set aside the screws. You’ll reinstall them in step 8.
6. Select a backplate Find the backplate that matches the brand of your existing lock.
7. Remove the paper from the stickers On the backside of t he backplate you’ll fi nd three stickers. Remove the paper f rom the stickers.
8. Fasten backplate Fasten the backplate where the thumb-turn was using the two original screws, with the arrow on the label pointing up. The notches on the backplate must be facing out with the tailpiece centered exactly in the middle hole.
9. Select tailpiece adapter Select the tailpiece adapter that matches the shape of your existing lock’s tailpiece. Baldwin Emtek Omnia Weiser Weslock 12 Baldwin Kwikset Schlage Depends on the length of your tailpiece.
10. Insert adapter into Danalock Insert the selected tailpiece adapter into your Danalock and press until it clicks in place.
11. Fit and fasten Danalock Fit the Danalock onto the backplate with the battery cover facing down, the tailpiece sliding into the adapter and the backplate notches into the back of the lock.
12. Align the platemarks Find the small marking at the edge of the backplate and align it with the hole in the cover ring surrounding the Danalock. Now you are sure to hit the notches on the backplate with the Danalock.
13. Fasten the Danalock Turn the Danalock clockwise until it clicks to fasten it to the backplate. NOTE: If you need to unfasten and retry, see “Uninstall instructions” on p. 22.
14. Activate batteries Pull out the plastic tab to activate the batteries. A light will flash to confirm the Danalock i s ready. Note: If the batteries are disconnected, you will have to re-calibrate the Danalock.
15. Before completing the setup Your Danalock is now attached to the door. Leave the door open, so the lock isn’t influenced when calibrated.
16. Open the Danalock app Open the Danalock app you downloaded at the start. When you have logged in you will see your empty keychain. Press ”Add lock” at the bottom of the screen. A guide will now lead you through the installation and configuration o f your Danalock.
17. Dismount instructions If at any time you need to dismount the Danalock from your door, insert a pen tip into the hole at the top inner edge of the lock and press while turning the lock counter- clockwise until the lock releases. This will not reset the lock or disconnect it from your account, b ut the lock may need to be re-calibrated if fastened to y our door again.
18. LED-Signals A LED light on the Danalock indicates the status of several operations with different colours: LED-Mode LED color Status indication Constant red till light finishes Lock has successfully locked Constant green till light finishes Lock has successfully unlocked Constant white for 3 seconds Power on.
19. Configuring the Danalock V3 with click-commands You can configure the Danalock via the button found in the small hole on the top of the lock. When you click through settings, the LED will change color according to the scheme on the next page. When you get to the setting you want to change, wait for 5 seconds and the Danalock will react to your command. If you make a wrong number of clicks, just stop at a number of clicks where the LED doesn’t light up and wait for 5 seconds.
Clicks Color Activity 1 Green Inclusion mode This mode is used to in- or exclude your Danalock with a Z-Wave or Zigbee gateway. When the Danalock blinks green it is in ex/inclusion mode and you have 30 seconds to pair the Danalock with a gateway. 2 Yellow Manual calibration Turn the Danalock to the desired unlocked position. Start the calibration with the click command and wait for the LED to start blinking yellow.
Danalock International ApS Gammel Stillingvej 427C 8462 Harlev, DK +45 4242 8122 info@danalock.com www.danalock.
