27-09-2005 11:01 Pagina 1 ANGLE GRINDERS DG4 1/2 DG5 DALTILE ANGLE GRINDER OPERATING MANUAL V09/2005R1 DG45 OPERATING MANUAL
DG45 27-09-2005 11:01 Pagina 2 CAUTION Carefully read and understand all Safety and Operating Procedures prior to using the Daltile® Angle Ginder Keep this Manual in a safe place for future reference. Enter the Serial Number of your new Daltile® Angle Grinder in the box below.
DG45 27-09-2005 11:01 Pagina 3 TABLE OF CONTENTS 1. DALTOOL SAFETY Safety Messages ..........................................................................................................................................4 Damage Prevention and Information Messages ......................................................................................4 General Safety Precautions and Hazard Symbols ....................................................................................
DG45 27-09-2005 11:01 Pagina 4 DALTOOL SAFETY It is extremely important that you read and understand all of the safety instructions, the operating instructions and the maintenance instructions. If these instructions are not followed, serious injuries and/or death could occur to you or to others. Also, failure to read and follow the enclosed maintenance instructions can lead to equipment failure, damage to the equipment or reduced lifetime of the equipment.
DG45 27-09-2005 11:01 Pagina 5 DALTOOL SAFETY ● KEEPING THE WORK AREA CLEAN. It is important that the working area be clean so as to avoid potential accidents or injuries. ● DO NOT USE THE EQUIPMENT IN DANGEROUS ENVIRONMENTS. It is important that power tools not be used in wet environments. The equipment should never be used in the rain. Also, it is advisable to keep the working area well lit. ● CHILDREN SHOULD BE KEPT AWAY FROM THE WORKING AREA.
DG45 27-09-2005 11:01 Pagina 6 DALTOOL SAFETY ● TOOL MAINTENANCE. It is important to keep tools clean and in good working order. This will result in optimal performance of the machine. Always follow the maintenance instructions for proper tool maintenance. ● REDUCING ACCIDENTAL STARTING OF MACHINE It is important to be sure that the switch is in the OFF position before plugging in the machine. It is important to check all the moving parts of the machinery for proper alignment and /or possible binding.
DG45 27-09-2005 11:01 Pagina 7 DALTOOL SAFETY HAZARD SYMBOLS ● READ MANUAL CAREFULLY BEFORE USE Carefully read and understand this operating manual and the enclosed safety instructions prior to using the machine. ● ELECTRICAL SHOCK It is important to never touch electrical components of the machine while the machine is in operation.
DG45 27-09-2005 11:01 Pagina 8 DALTOOL SAFETY The use of this machine generates dust. Excessive airborne particles may cause irritation to eyes, skin and the respiratory tract. To avoid breathing impairment, always us dust controls and protection suitable to the material being mixed. Comply with American National Standards Institute Safety Code, B7.
DG45 27-09-2005 11:01 Pagina 9 MACHINE SPECIFICATIONS BLADE GUARD HAND GRIP SPINDLE LOCK VENTILATION SLOTS MAIN SWITCH GRINDING DISK SIDE GRIP Technical Data: Voltage Motor No Load Speed Spindle Lock Spindle Thread Spindle Arbor Blade Capacity Weight Machine Length [V/Hz] [W/HP/A] [RPM] -[Inch] [Inch] [Inch] [lbs] [Inch] DG41/2 DG5 115/60 750/1/7 10,000 yes 5/8 - 11 7/8 4 1/2 3,9 10 1/2 115/60 1200/1,5/10 10,000 yes 5/8 - 11 7/8 5 5.
DG45 27-09-2005 11:01 Pagina 10 OPREATING INSTRUCTIONS 1. INSTALLING THE GRINDING DISK 2. GRINDING PROCESS 1. Grinding pressure Turn off and unplug the machine before mounting or replacing the grinding disk. Never use a grinding disk with a lower RPM than that of your angle grinder (See specifications). 1) Turn the machine over with the spindle facing upward and mount the flange. Rotate the flange until you feel it locking. 2) Mount the grinding disk.
DG45 27-09-2005 11:01 Pagina 11 REPAIR & MAINTENANCE 4. Motor Always unplug the machine before attempting any maintenance. 1. Replacement of grinding disk Grinding disks should be replaced when worn to the following values: - Ø4 1/2” reduced to Ø3”. - Ø5” reduced to Ø3”. 2. Inspection of screws The rotor and stator in the motor are the core of the machine. Do not scratch the surface of the windings in the motor, and never apply oil or water on it. 5.
DG45 27-09-2005 11:01 Pagina 12 DALTOOL ANGLE GRINDERS PAGE 12 DALTILE ANGLE GRINDER OPERATING MANUAL V09/2005R1
