27-09-2005 11:16 Pagina 1 ANGULAR TILE DRILL DAD2 DALTILE DAD2 OPERATING MANUAL V09/2005R1 DAD2 OPERATING MANUAL
DAD2 27-09-2005 11:16 Pagina 2 CAUTION Carefully read and understand all Safety and Operating Procedures prior to using the Daltile® Angular Tile Drill DAD2. Keep this Manual in a safe place for future reference. Enter the Serial Number of your new Daltile® Angular Tile Drill DAD2 in the box below.
DAD2 27-09-2005 11:16 Pagina 3 TABLE OF CONTENTS 1. DALTOOL SAFETY Safety Messages ..........................................................................................................................................4 Damage Prevention and Information Messages ......................................................................................4 General Safety Precautions and Hazard Symbols ....................................................................................
DAD2 27-09-2005 11:16 Pagina 4 DALTOOL SAFETY It is extremely important that you read and understand all of the safety instructions, the operating instructions and the maintenance instructions. If these instructions are not followed, serious injuries and/or death could occur to you or to others. Also, failure to read and follow the enclosed maintenance instructions can lead to equipment failure, damage to the equipment or reduced lifetime of the equipment.
DAD2 27-09-2005 11:16 Pagina 5 DALTOOL SAFETY ● KEEPING THE WORK AREA CLEAN. It is important that the working area be clean so as to avoid potential accidents or injuries. ● DO NOT USE THE EQUIPMENT IN DANGEROUS ENVIRONMENTS. It is important that power tools not be used in wet environments. The equipment should never be used in the rain. Also, it is advisable to keep the working area well lit. ● CHILDREN SHOULD BE KEPT AWAY FROM THE WORKING AREA.
DAD2 27-09-2005 11:16 Pagina 6 DALTOOL SAFETY ● TOOL MAINTENANCE. It is important to keep tools clean and in good working order. This will result in optimal performance of the machine. Always follow the maintenance instructions for proper tool maintenance. ● REDUCING ACCIDENTAL STARTING OF MACHINE It is important to be sure that the switch is in the OFF position before plugging in the machine. ● EQUIPMENT ACCESSORIES.
DAD2 27-09-2005 11:16 Pagina 7 DALTOOL SAFETY HAZARD SYMBOLS ● READ MANUAL CAREFULLY BEFORE USE Carefully read and understand this operating manual and the enclosed safety instructions prior to using the machine. ● ELECTRICAL SHOCK It is important to never touch electrical components of the machine while the machine is in operation.
DAD2 27-09-2005 11:16 Pagina 8 DALTOOL SAFETY The use of saws and drills generates dust. Excessive airborne particles may cause irritation to eyes, skin and the respiratory tract. To avoid breathing impairment, always us dust controls and protection suitable to the material being sawed or drilled; See OSHA (19 CFR Part 1910.1200). Diamond Blades improperly used are dangerous. Comply with American National Standards Institute Safety Code, B7.
DAD2 27-09-2005 11:16 Pagina 9 MACHINE SPECIFICATIONS 1. Diamond Tile Bit 2. Water Injection Head 3. Side Grip 4. Main Switch 5. Speed control 6. Water connection 7. Socket Head Screw Driver 3 mm 8. Drilling Guide 9. Water Tank 10. Operating Manual 11. Carrying Case (not shown) Technical Data: Voltage Motor No Load Speed (stageless) Max. Bit Capacity Spindle Lock Weight [V DC] [W/HP/Amp] [RPM] [Inch-Metric] -[lbs] 115 750/1/7 3,000 - 10,000 2-51 yes 5.
DAD2 27-09-2005 11:16 Pagina 10 OPERATING PROCEDURES CHECK BEFORE USE: ● Unpacking: Unpack the tile drill and check for missing or damaged parts. ● Power Supply: Make sure that the power supply corresponds with the information on the machine. DRILLING ● Use the machine only in combination with the supplied water tank or direct connection to the main water supply. ● Always use the drill guide. drilling unit. Fill the water tank to the maximum quantity as indicated and pump the pressure to 1 bar.
DAD2 27-09-2005 11:16 Pagina 11 REPAIR & MAINTENANCE Installation of the Diamond Bits: ● Prior to the installation of the diamond bit it is important that both the machine adapter and the diamond bit are cleaned and greased. ● Mount the bit with the flat side opposing the locking screw. ● Secure the bit using the socket head screwdriver ● Remove the socket head screwdriver. ● Removal of the bit is done in reverse order.
DAD2 27-09-2005 11:16 Pagina 12 DIAMOND TILE BITS Diamond Tile Bits Description DalTool® 1/4” DalTool® 5/16” DalTool® 3/8” DalTool® 1/2” DalTool® 5/8” DalTool® 11/16” DalTool® 3/4” DalTool® 7/8” DalTool® 1” DalTool® 1 3/8” DalTool® 1 1/2” DalTool® 1 3/4” DalTool® 2” DalTool® 2 5/8” Metric (6 mm) (8 mm) (10 mm) (13 mm) (16 mm) (18 mm) (20 mm) (24 mm) (26 mm) (35 mm) (40 mm) (45 mm) (51 mm) (68 mm) PAGE 12 DALTILE DAD2 OPERATING MANUAL V09/2005R1 Part-Number 9999 541874 9999 541875 9999 540956 9999 54
