Specifications

51
ACCESSORIES
LED'S
Item 536 ......... T1 (3mm) Incandescent White LED (color temp. of
a light bulb). Super Bright output 6000 M.S.C.P. @
20ma. typical. 45 degree viewing angle.
Item 537 ......... T1¾ (5mm) Incandescent White LED (color temp.
of a light bulb). Super Bright output 12300 M.S.C.P.
@ 20ma. typical. 20 degree viewing angle.
Item 532 Item 533 Item 534
T1 Red T1 Yellow T1 Green
Item 542 ......... SPECIAL SHAPE RED LED. Use for engine and
caboose marker lights. Front nib measures 0.079"
dia. x 0.14" l, main body x 0.196" dia. x 0.177"
length.
Item 593 ......... DUAL COLOR RED/GREEN LED with common
Anode (+). Use for classification lights and other
applicatoins. T1 (3mm) case size.
All LED's require an appropriate limiting resistor for the voltage
applied. They cannot be reverse biased (i.e., place a voltage
reverse of the proper polarity) or they will burn out. To prevent
reverse polarity problems either place a diode or bridge
rectifier in the power path. Wiring diagrams are shown on our
web site.
See price schedule or web site for appropriate resistors,
diodes, and bridge rectifiers.
Various wiring diagram's are shown with the LED's package.
Ultra Miniature Connectors
Item 757 ................ 2 pin connector pack. Includes 5 sets of ultra
miniature connectors. Female connector is
supplied with leads already crimped and
inserted. Male end requires soldering of wire to
pins. Heatshrink tubing is included. Connector
spacing is 0.049", height (when connected) is
0.22"h, 0.2" d x 0.147" w footprint.
Item 758 ................ 3 pin connector pack. Same as item 757
except contains 4 / pac, 0.196" w.
Item 222 ................ 6" 2 pin wire harness
Item 223 ................ 6" 3 pin wire harness
Item 224 ................ 18" 2 pin wire harness
Item 225 ................ 18" 3 pin wire harness
Terminal Block
Item 340 ..... 6 position. 15amp, 250v.
Switches
Item 618 ...... SPST momentary push button. 3amp, 125v.
Mounting hole: 0.4" (13/32 - 7/16)
Item 524 ...... SPDT toggle switch. 3amp, 125v.
Mounting hole: 13/64" (0.193").
IItem 989 ..... SPST reed switch. Small in size, body measures
0.1" dia x 0.591" max. length. 140vAC/DC,
0.75amp. Operate Range 8-16 AT, Release Range
4-14 AT. (2/pk)
See price schedule for items not shown!
Lamps
Item 539 ......... Ballast Lamp (18 Volt, 0.15 Amps, 2/pack). May
also be used to illuminate buildings, great with 16
volt input voltage from transformer Item 690. Uses
Item 548 bayonet base.
Item 548 ......... Bayonet Base for 539 & others. This base is fully
insulated from the mounting bracket!
Item 538 ......... Ballast Lamp Assembly. Includes one lamp and
bayonet base as above.
Item 383 ......... 2.7 volt, 60 mA, miniature lamp. Replacement
lamps for regulated lighting units and other uses.
(0.225" dia x 0.51" h, bright output of 0.040
M.S.C.P., 6000 hour typical life. Physical attributes
are typical and may vary).
Miniature Connectors
All connector packs include appropriate number of male and
female connectors with wire crimp connectors, also includes
heat-shrink tubing for insulating the male stub end. Connector
spacing is 0.1", height (when connected) is 0.65".
Item 520 ................... 2 pin connector pack.
Item 521 ................... 3 pin connector pack.
Item 611 .................. 4 pin connector pack.
crimp pins for above connectors. Shown without
wire and with wire after crimping operation.
Slides into female housing and locks for secure fit.