Technical data
15.
Technical data
PD4-M-TRIO-DALI
Sensor and power supply in one case
Power supply: 230V~ ±10%
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class: IP20 / II
Settings: control dial, DIP switch and
remote control
Light values-Remote control: 100 - 1000 Lux
Extension of the detection area: with Slaves
Area of coverage: circular 360°
Range of coverage Ø H 2.50m / T=18°C:
seated 6.40m / tangential 24 m / radial 8m
Recommended height for mounting: 2 - 3 m
Light measurement: Mixed light, daylight +
artificial light
Lux values-Potentiometer: 10 - 1200Lux
• DA 1/2 for light switching, light-controlled
• DA 3
for light switching
(
panel lighting
),
light-controlled
DA 1/2 DALI-BUS regular
Max. numbers of connected EB‘s:
each 25 for DA1 and DA2, 10 for DA3
Time-settings: 1 - 60min. / Test
Dimensions H x Ø [mm] SM FC
PD4-M-TRIO-DALI 124 x 85 100 x 117
Visible portion when built into ceiling: H 37 x Ø 117mm
Declaration of Conformity: The product complies with
the low voltage recommendation 2006/95/EC and the
EMV recommendation 2004/108/EC.
13. Wiring diagram
14. PD4-M-TRIO-DALI – Connections
In case the sensing area of the LUXOMAT
®
PD4-M-
TRIO-DALI is too large or areas are being covered that
should not be monitored, the range can be reduced or
limited through use of the enclosed masking clips (e).
11. Exclude sources of interference
10. Range of Coverage
16. DIP switch functions
PD4-M-TRIO-DALI
1
1
2
Walking across
Walking towards
Seated
quer zum Melder gehen
frontal zum Melder gehen
sitzende Tätigkeit
DIP
switch
OFF ON
1 (A) Fully automatic channel
DA 1/2 + DA3
Semi-automatic channel
DA 1/2 + DA3
2 (B) For mains ON /
light ON
For mains ON /
light OFF
3 (C) Standard operation RESET
17. LED function displays
18. Fault-finding
Permanently flashing
Check whether DIP3 switch (RESET) is set to “ON”
Reset to “OFF” if necessary
DIP
ON
OFF
1 2 3
e
LED Colour Function Display
6 red Motion indicator Lights up for motion
detection
5 green Light status indicator
DA 1
flashes twice per sec.:
-
bright enough (light OFF)/
too bright (light ON)
flashes once per sec.:
- Delay time active
4 white HA/VA DA 1/2 lights when semi-automatic
3 white HA/VA DA 3 lights when semi-automatic
2 green Light status indicator
DA 2
flashes twice per sec.:
-
bright enough (light OFF)/
too bright (light ON)
flashes once per sec.:
- Delay time active
1 red OFF-function lights when the feature
is activated, ie in the
initialization phase the
light is off
all LEDs Acknowledgement flashes once per sec.:
- correct input
flashes twice per sec.:
- incorrect input
flashes three times / once
per sec.:
- Reset when locked
flashes three times / twice
per sec.:
- Double locked
all LEDs Status flashes shortly once per
sec.:
- Detector is double locked
MAN 6621 – 300811–2
8. Manual Dimming
(for IR-PD4-TRIO-DALI functions see page 1)
You can dim manually by pressing the pushbutton for a long
time (> 2 sec.). When the button is released, the current dim-
ming value is retained. Upon renewed dimming, the dimming
direction is reversed.
7. Fully / Semi automatic mode
(see DIP switch functions and IR-PD4-TRIO-DALI on page 1)
Automatic operation
In this operating mode, the lighting switches automati-
cally on and off for increased comfort, depending on
presence and brightness.
Semiautomatic operation
In this operating condition, in order to gain increased
savings, the lighting is energized only after being manu-
ally switched on. Switch-off takes place automatically.
The semiautomatic mode basically behaves like the fully
automatic one. However, the difference is that switching-
on must always be carried out manually!
As many (closer-contact) buttons as desired can be wired
in parallel on the “S” button input (ON/OFF DIM).
9. Manual Switching
You can switch the lighting on and off manually by pressing
the pushbutton for a short time. It will stay on or off as long
as people are detected plus the congured follow up time.
Type SM FC FM
PD4-M-TRIO-DALI (Master) 92750 92755 –
PD4-S (Slave) 92142 92254 92163
LUXOMAT
®
Remote control:
IR-PD4-TRIO-DALI (incl. wall bracket) 92104
Accessory:
Wire basket BSK 92199
Wall bracket for remote control as replacement 92100
SM-Socket IP44 for 92730 92386
12. Article / Part nr. / Accessory
WE RECOMMEND THAT BEFORE DIMMING OF THE CONNECTED
LIGHTS A 100h BURN IN (T5 TUBES OR 80 HOURS FOR T8 TUBES)
FUNCTION TAKES PLACE. THIS CAN BE IGNORED BY USING THE
REMOTE CONTROL TO DEACTIVATE.
THE LIFESPAN OF THE LAMPS CAN BE REDUCED IF THE BURN IN DOES
NOT TAKE PLACE.
2
optional
T1&2 = NO button for semi-automatic mode
Slave for enlargement of detection area
PD4-M-TRIO-DALI-FC
PD4-M-TRIO-DALI-SM
12 m
12 m
8 m
6.40 m
24 m
360°
2.50 m
LNR
–
DA3
+
DA2
+
S
DA3
S
DA
1/2
DA1
– +
L L N N R
L
N
R
Slave
T1T2
DA –
DA +
DA –
DA +
DA –
DA +
L
N
R
Slave
T1T2
DA –
DA +
DA –
DA +
DA –
DA +
S
DA3
S
DA
1/2
+ –
DA2
+ –
DA1
– +
DA3