Dakota Alert™ PR-3000 Portable Receiver Owner’s Manual
CONTENTS The PR-3000, battery charger, and belt clip. (figure 1) Figure 1 WARNING This device complies with Part 15 of the FCC rules, operation of this device is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation. INTRODUCTION The PR-3000 receiver is compatible with all Dakota Alert 3000 Series transmitters (WMT-3000, WPT-3000, WHT-3000, UT-3000, and IR-3000).
When a signal is received, the zone will be displayed on the LCD screen and the receiver can be set to give an audible tone or a silent vibrate alert. Each zone can store up to 400 events with a time and date stamp or up to 999 events without a time and date stamp. The PR-3000 is powered by a rechargeable LiIon battery which will hold a charge for up to 10 days. CHARGING THE PR-3000 To charge the PR-3000 plug the battery charger into an outlet and insert the jack into the charger plug (#5 on figure 2).
Figure 2 1 THE PR-3000 (figure 2) 1. LCD display 2. (Side button) ON/OFF and Mode button 3. Left Button 4. Right Button 5. Charger plug 6. Reset button 6 4.
LCD Display - Time/Date Mode (Figure 3) 1. Time and Date mode 2. Audible Tone icon 3. Vibrate Alert icon 4. Lock icon 5. Battery Charge Indicator 6. Time (24 hour mode) 7. Date 1 3 2 4 LCD Display Alert Mode (Figure 4) 1. Last Channel received 2. Number of alerts stored on the indicated channel 3. Time stamp of alert 4. Date stamp of alert 2 5 1 3 6 4 7 Figure 4 Figure 3 5.
Alert Mode When the PR-3000 receives an alert, the LCD display changes to alert mode. The display will remain in alert mode, showing the most recent alert received until manually reseting to time/date mode. Push the right button to change from the alert mode to the time/date mode. Programming the Receiver Push the side and right buttons at the same time to enter the programming mode. There are four different programming screens. Pushing the side button will scroll through the programming screens.
Setting the Time and Date 1. Push the side and right button to enter the time/date setting screen in the programming mode. The hour digits will be flashing. 2. Push the right button to change the hour to the correct setting. (holding the right button down will scroll through the numbers quickly.) 3. Push the left button and the minutes will start flashing. 4. Push the right button to change the minutes to the correct setting Figure 5 5. Repeat this process to set the month, day, and year.
Programming the vibrate alert From the audible tone setting screen, push the side button to access the vibrate alert programming screen. The vibrate alert icon will flash and there will be “ON” or “OFF” in the upper right section of the display. Use the right button to toggle between on and off. (figure 6) Programming the Frequency From the vibrate alert programming screen, push the Figure 7 side button to access the frequency programming screen.
Locking the display Pushing the left and right buttons at the same time will lock the display in the time/date mode. The top of the display (figure 3) and no other screens can be viewed. Pushing the left and right buttons again will unlock the display. Viewing Alert log Push the side and left buttons at the same time to acess the alert log. The display will show the channel and the total number of alerts stored for that channel.
Clearing the alert log The alerts stored for a channel can be cleared through the alert log screen. Access the alert log, display the channel to be cleared, and push the side button. The text CLrECOrd (clear record) will appear on the bottom of the display (figure 8). Push the side button again and all stored alerts for the chosen channel will be cleared. Figure 8 Reset button If the PR-3000 stops responding correctly, the reset button should be pushed.
TECHNICAL SUPPORT If you encounter any difficulty in the operation of this product after reading the manual, please contact us. You can reach us by phone at 605-356-2772 from 8:30 AM to 5:00 PM Monday through Friday (Central Standard Time). We will be happy to answer your questions and help you in any way we can. WARRANTY Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase.
Dakota Alert, Inc. 109 W. Main St. P0 Box 130 Elk Point, SD 57025 Phone: (605) 356-2772 Fax: (605) 356-2584 Web: www.dakotaalert.
