INSTRUCTIONS AND PARTS LIST POWER HAMMER DAKE (Division of JSJ) 724 Robbins Road Grand Haven, Michigan 49417 616.842.7110 Phone 800-937-3253 616.842.0859 Fax 800-846-3253 Web: www.dakecorp.com E-mail : customerservice@dakecorp.com technicalsupport@dakecorp.
Set up and Operation of the Dake Power Hammer Once you remove the power hammer from the packaging you will need to install the shaping dies to be used and the wheels. WARNING !!! Unplug the power hammer from the electrical source before changing the dies. A. Remove the 6 bolts from the adjustable bottom sleeve. B. Remove the adjustable bottom sleeve from the side plates. C. Insert die holder with the desired die attached into the slider. Make sure the die holder is bottomed into the slider. D.
Set up and Operation of the Dake Power Hammer E. Rotate the adjusting screw handle to move the bottom adjustment rod down. F. Insert the die holder with the desired die attached into the adjustable bottom sleeve. Make sure the die holder is bottomed into the adjustable bottom sleeve. G. Snug up the two hex socket set screws on the adjustable bottom sleeve to hold the die holder firmly but still allow it to move up by turning the adjusting screw handle.
Set up and Operation of the Dake Power Hammer I. Insert adjustable bottom sleeve (B) and attach six bolts through the side plates and into the adjustable bottom sleeve.
Set up and Operation of the Dake Power Hammer J. Make sure the lock screw on the adjustment bottom sleeve is loose. K. Rotate adjusting screw handle to move the lower die to the upper die. WARNING !!!! For safe operation and possible die damage always adjust the gap between the upper die half and the work piece to a minimum of ¼” before starting motor.
Set up and Operation of the Dake Power Hammer L. Check the two set screws on the die holder to see if they are tight. These hold the lower die firmly in place. M. The upper and lower dies need to be lined up. If they do not line up, loosen the bolts holding the dies to the die holders and align the dies. Don’t forget to retighten these bolts.
Set up and Operation of the Dake Power Hammer WARNING !!! Before turning on power to your Dake power hammer be sure to review all safety stickers and warnings. N. With the motor turned on, the upper die holder will begin to oscillate. Rotate the adjusting screw handle to move the lower die up until just before it touches the upper die. This is a good initial setting to try shaping with. O.
10/09/07 Dake Power Hammer 8
Item # 1 2 3 5 6 7 8 9 10 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 10/09/07 Dake Power Hammer Part description Side Plate Rear spacer Plate Front Mount Plate 2 Bolt Flange Bearing Offset Shaft (27”) Connecting Rod Cast Bronze Bushing Slider Top Collet Slide Gulide & Bushing Shoulder Bolt Bearing Washer (center hole 5/16 bolt) Bottom Collet Bottom Adjustment Rod Hand Wheel Die Holder Upper Die Lower Die Qty 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 Part #
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 67 68 69 70 71 72 73 74 75 76 10/09/07 Dake Power Hammer ½ Grade 8 Hex Cap Screw 3/8-16 UNC x 1 1-1/4 Grade 8 Hex Head Cap Screw 5/8-11 UNC X 1-1/4 Socket Head Cap Screw ¼-20 x 3/8 Key Stock 3/16 x 3/16 Socket Head Cap Screw ¼-20 x ¾ UHMW Poly Rod 1 Grade 8 Hex Bolt 5/16-18 x 1 Bottom Sleeve Cross Brace 4 1 2 301929 87147 301893 RivNuts ¼-20 Grade 8 Washer 3/8 6 12 301933 Bottom Spacer, Base 1 87162 Grade 8 Nut 5/16 Grade 8 Hex Bolt
You are now ready to start shaping metal Everyone has their own technique when it comes to shaping and you will need to find your own. So, practice, think , practice and think some more before practicing again. We have found that like forming by hand, it is easier to get the desired shape using the Dake power hammer by using several steps to “sneak up” on the final shape, versus trying to get the shape in one step.
Safety stickers that are located on the Dake power Hammer WARNING!!!! Review all safety stickers before operating this machine.
110 volt Machine 10/09/07 Dake Power Hammer 13
220 volt single phase machine 10/09/07 Dake Power Hammer 14
