DAKE SINGLE PHASE DURA-PRESS Force 10DA INSTRUCTIONAL MANUAL WARNING! Read and understand all instructions and responsibilities before operating. Failure to follow safety instructions and labels could result in serious injury. Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 Phone: 800.937.3253 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TABLE OF CONTENTS DAKE STANDARD LIMITED WARRANTY ............................................................ 2 RETURN & REFUND POLICY ............................................................................... 4 SAFEGUARDING THE POINT OF OPERATION ................................................... 5 SPECIFICATIONS ..................................................................................................
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com DAKE STANDARD LIMITED WARRANTY Finished Machines Dake warrants to the original purchaser the finished machine manufactured or distributed by it to be free from defects in material and workmanship under normal use and service within 1 year (12 months) from the delivery date to the end user.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Warranty Exceptions: The following conditions are not applicable to the standard limited warranty: (a) Part installation or machine service was not completed by a certified professional, and is not in accordance with applicable local codes, ordinances and good trade practices.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com RETURN & REFUND POLICY Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are here to help. Returns All Dake manufactured / distributed machines, parts and couplings include a 30-day return option. These policies are valid from the date of final shipment to the end user. To be eligible for a return, the item must be unused and in the same condition as received.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SAFEGUARDING THE POINT OF OPERATION ANSI B11.2 - Hydraulic Power Presses Safety Requirements for Construction, Care, and Use It is important that Dake press users have a clear understanding of their responsibility involving the care and use of their Dake hydraulic press, including point-of-operation safe guards.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SPECIFICATIONS Model Number Capacity Horse Power Voltage Ram Travel Pressing Speed Width between uprights Max. ram to table Height Base Weight Force 10DA 909205 10 tons 1 HP 110V Single Phase 10” 20 ipm 20” 40” 80” 29-3/4” x 24” 3,450 lbs. In the space provided record the serial number and model number of the machine. This information is only found on the black and gold Dake tag shown below.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SAFETY This is the safety alert symbol. When you see this symbol on your press be alert to the potential for personal injury. Employer is responsible to perform a hazard/PPE assessment before work activity. Label Placement View Label Part No. 300168 Label Part No. 76462 909205 Label Part No. 84399 Label Part No. 302070 7 Label Part No. 84395 Label Part No.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Follow recommended precautions and safe operating practices. It is important that the operator understand all safety instruction listed below in order to prevent damage to themselves, others, or the machine: • Carefully read all the safety messages in this manual and on your press safety labels. Keep safety labels in good condition. Replace missing or damaged safety labels. • Do not alter this press from its original design.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com WIRING INSTRUCTIONS WARNING: A licensed qualified electrician that follows all state and local laws must wire and install electrics on this press. 110 Volt WARNING: Machine must have a designated 30 amp drop for 110 volts. This press will not operate correctly without 30 amps. For 110 volts this machine is ready to plug in. The machine can be wired 220-volt single phase.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com MAINTENANCE LUBRICATION Keep all working parts of press well oiled for easier operation. Also, keep a light film of oil over the entire surface of the ram to prevent rust. HYDRAULIC LINES AND FITTINGS If there is ever any maintenance done with the hydraulic components below is how to reinstall all components. Item 1 2 3 4 5 6 7 8 9 909205 10 Part No.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TROUBLESHOOTING SYMPTOM CAUSE SOLUTION This press has a selfbleeding system, continue to run the ram up and down approximately 15 times. Remove octane cap from back of manifold and adjust set screw to correct pressure. WARNING: Do not exceed 2413 PSI Remove octane cap from back of manifold and adjust set screw to correct pressure.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Item 1 2 3 4 5 6 7 8 9 11 12 13 20 23 24 25 27 28 29 30 31 32 33 34 Part Description Part No.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 10 DA WORKHEAD DIAGRAM Item A B C D E F G H J - Description Piston Cylinder Flange Cylinder Socket Head Cap Screw O-Ring Seal Wear Ring Wear Ring O-Ring Seal Workhead Assembly Part # 86690 86689 86688 43450 78483 78484 78485 78486 78487 716514 10 Ton DA Workhead Specs 3-1/4” Dia. Bore 1-3/4” Dia. Rod 10-1/4” Actual Stroke 10” Rated Stroke 66 lbs. Total Weight Please contact factory for current prices.
