Manual

ManualsBrandsDaisy ManualsAirguns008

NOT A TOY. ADULT SUPERVISION REQUIRED. MISUSE OR

CARELESS USE MAY CAUSE SERIOUS INJURY OR DEATH. MAY BE DANGEROUS UP TO

240 YARDS (220 METERS).

THIS IS A HIGH POWER AIR GUN RECOMMENDED FOR USE BY THOSE 16 YEARS OF

AGE OR OLDER. READ ALL INSTRUCTIONS BEFORE USING. THE PURCHASER AND

USER SHOULD CONFORM TO ALL LAWS GOVERNING USE AND OWNERSHIP OF AIR GUNS.

WARNING:

OPERATION MANUAL

WARNING: THIS GUN CAN CAUSE DEATH IF CARELESSLY USED

OR MISUSED. READ AND FOLLOW THE INSTRUCTIONS CAREFULLY. DO NOT

INSTALL A CLIP WHICH CONTAINS AMMUNITION INTO THE GUN UNTIL YOU ARE

READY TO SHOOT. IF YOU DO INSTALL A CLIP WHICH CONTAINS AMMUNITION INTO

THE GUN AND THEN DECIDE NOT TO SHOOT, EITHER MANUALLY REMOVE THE CLIP

FROM THE GUN OR SHOOT THE REMAINING AMMUNITION AT A SAFE TARGET. AN

UNLOADED, NON-PRESSURIZED GUN WHICH IS “ON” SAFETY IS SAFEST. ACCI-

DENTS HAPPEN FAST, AND ACCIDENTALLY INJURING OR KILLING SOMEONE IS A

TERRIBLE THING. PLEASE SHOOT SAFELY.

This safety alert symbol indicates important safety messages in this manual.

When you see this symbol, be alert to the possibility of personal injury and care-

fully read the message that follows.

The Model 008 CO

PowerLine pistol shoots with much more muzzle energy than

most BB and pellet guns. Use extreme caution when operating this gun.

Although your new PowerLine pistol is not a firearm, it has lethal potential and

should be trea

ted with the caution and respect due an

y conventional firearm. Like a

firearm,

your P

owerLine pistol, when misused or carelessly used, can kill or serious-

ly injure the shooter or other persons.

ways remember, the first and most important

safety fea

ture of an

y gun is the shooter. All safeties are mechanical devices and the

shooter is the only part of the system tha

t can make a gun safe–or unsafe.

DON’T

DEPEND ON MECHANICAL SAFETIES–think ahead and a

void situa

tions that might

lead to accidents.

Guns differ in their opera

tion,

and you are never read

y to fire an

y gun until you

are thoroughly familiar with it.

Read the follo

wing opera

ting instructions and

WITH

OUT LOADING

ANY

AMMUNITION,

proceed through the opera

ting steps,

y firing your

gun with CO

only several times a

t a safe target.

This will enable you to learn to oper

te the P

werLine 008 properly and safely

.177cal. (4.5mm) LEAD AIRGUN PELLET

.177 cal BB (4.5 mm) STEEL AIRGUN SHOT

2gm CO

ylinder only

MODEL 008 By

SEMI-AUTOMATIC

NEVER STORE A LOADED GUN

t the end of a shooting session, as a safety precaution, always put safety “ON SAFE” (S),

emove CO

ylinder, remove clip from pistol, and remove any ammunition from the clip. Store

n a safe place to prevent unauthorized use.

INSERT CO2 CYLINDER

1. Put safety "ON SAFE” (S) - red dot covered (Fig. 4).

. Remove left grip cover by lifting the grip cover tab (Fig. 2A).

. Open puncture lever until there is enough room to insert a CO

ylinder. Insert the large end

of the CO

cylinder into the lower portion of the grip (Fig. 2B).

. Hold the gun in an inverted position with the grip pointing up and the muzzle pointing away

rom you. Position the small end of the CO

ylinder inside the retainer so that the CO

ylin-

er touches the puncture pin (Fig. 2C).

. While continuing to hold gun in an inverted position, replace the left grip cover, point the

uzzle in a safe direction and close the puncture lever firmly to puncture the CO

ylinder

(

Fig. 2D).

ARNING:

e sure the muzzle is pointed in a safe direction when puncturing a CO

ylinder.

In the event that a seal temporarily leaks while a CO

cylinder is being punctured, the CO

gas

ay escape through the barrel. If ammunition is jammed in the barrel from prior shooting, this

ould result in a projectile being shot.

ARNING:

se only 12 gram CO

ylinders. Any attempt to use other types of gas cylinders

could be extremely dangerous and could result in serious injury. Gasses other than CO

could

esult in an explosion or rupture of the gun.

LOAD ROTARY CLIP

. Open breech of pistol by depressing barrel housing latch. Rotate the barrel housing downward

at the muzzle end to open the breech (Fig.5).

. Remove rotary clip and insert a total of eight projectiles into the rotary clip from the solid side

f the clip.

(

.177 cal. pellets and/or BBs only)

(

Fig. 3).

HOW TO OPERATE

RNING:

e sure gun is alw

ays pointed in a safe direction.

Step 1.

PUT SAFETY “ON SAFE” (S)- RED DOT COVERED.

Rota

te safety lever toward the "ON

SAFE" (S) position (F

ig. 4). With the safety in this position, the trigger CAN be pulled although the

un will not discharge any

r ammunition.

he safety is manual and not automat

ic. It

will only do its job when you do yours.

EMEMBER, THE BEST SAFETY IS GOOD GUN HANDLING.

Step 2.

Open breech of pistol by depressing barrel housing la

tch. Rotate the barrel

ousing downward at the muzzle end to open the breech (Fig.5). Insert a loaded clip fully into

reech of barrel so that

hole in center of clip seats onto breech pin (Fig. 6). Close barrel housing.

tep 3. AIM AT SAFE TARGET

o be a consistent marksman, use the correct sight picture each

time you fire the pistol (F

ig. 7).

AUTION:

Due to the po

wer of this CO

pistol,

use extra caution in selecting a safe target and

roper backstop based on the ammunition you’re shooting. N

ever shoot BBs into a steel trap

esigned for pellets and never shoot pellets at a target/backstop designed for BBs. Pick tar-

gets and backstops tha

t will not cause a ricochet or allow the ammo to penetrate the

ackstop. Never shoot at a flat hard surface or at the surface of water.

tep 4. T

AKE SAFETY “OFF SAFE” (F) - RED DOT SHOWING.

hen you are certain that

the

arget, back stop and surrounding area are safe, take the gun “OFF SAFE” (F) by sliding the safe-

ty release button to

ward the rear and rotate the safety lever toward the “OFF SAFE” (F) position

(

Fig. 8). Your gun is now ready to shoot. Pulling the trigger now will shoot a projectile out of the

un. In this condition, your gun should be handled with extreme care.

Step 5. FIRE The pistol can be safely fired after properly completing the operating steps

mentioned above. After making sure the gun is pointed in a safe direction, gently but firmly,

queeze the trigger. If you desire to continue shooting, the operation steps can be repeated until

he CO

ylinder requires replacement. If a projectile does not fire after completing the opera-

tion steps, keep the gun pointed in a safe direction and make the following checks:

1. Safety is pointing to "OFF SAFE" (F) position.

. Put safety “ON SAFE” (S) (Fig. 4) and check to see that a CO

ylinder with sufficient CO

gas is installed and the puncture lever is fully closed.

3. Refer to the section on "CO

Characteristics".

WARNING: If the pistol still fails to shoot a projectile after checking the three items above and

repeating the operation steps, there is a malfunction in the pistol. This could represent a dan-

gerous condition. There could be ammunition in the pistol even though it did not shoot out. This

could cause the user to mistakenly believe the pistol is unloaded. (Refer to "Pistol Malfunction"

section to correct the problem).

PRIOR TO OPERATION

PUT SAFETY “ON SAFE” (S) – POSITION SAFETY LEVER TO COVER RED DOT.

OPERATION STEPS

WARNING: Be sure gun is always pointed in a safe direction. Insert CO

cylinder.

un can continue to be shot until the ammunition clip or the CO

ylinder needs to be

eplaced. The Model 008 will obtain a minimum of 60 shots per CO

ylinder. Refer to section

on CO

characteristics.

tep 1. Put “ON SAFE” (S) - red dot covered.

Step 2. Load

tep 3. Aim at safe target.

Step 4. Take "OFF SAFE” (F) - red dot showing.

Step 5. Fire.

FRONT SIGHT

MUZZLE

TRIGGER

REAR SIGHT

GRIP

BARREL HOUSING LATCH

FIG. 1

FIG.

RETAINER

PUNCTURE PIN

FIG. 5

FIG.

CORRECT SIGHT PICTURE

BULLSEYE

REAR SIGHT

FRONT SIGHT

FIG. 3

FIG. 4

FIG.

FIG. 2A

SAFETY

FIG. 2B

FIG. 2C

FIG. 2D

GRIP COVER

GRIP COVER T

SAFETY

RELEASE

BUTTON

SAFETY LEVER

PUNCTURE LEVER

SAFETY RELEASE BUTTON

HOLE ON BACK

BREECH PIN

Summary of content (2 pages)

PAGE 1
PRIOR TO OPERATION O P E R AT I O N M A N U A L PUT SAFETY “ON SAFE” (S) – POSITION SAFETY LEVER TO COVER RED DOT. OPERATION STEPS WARNING: Be sure gun is always pointed in a safe direction. Insert CO2 cylinder. Gun can continue to be shot until the ammunition clip or the CO2 cylinder needs to be replaced. The Model 008 will obtain a minimum of 60 shots per CO2 cylinder. Refer to section on CO2 characteristics. Step 1. Put “ON SAFE” (S) - red dot covered. Step 4. Take "OFF SAFE” (F) - red dot showing.
PAGE 2
4. SHOOT AMMUNITION OUT A. Insert a new CO2 cylinder. B. Shoot gun according to the operation steps. WARNING: If the pistol still fails to shoot ammunition out of the barrel, the pistol should have the CO2 cylinder removed, and the pistol should be sent directly to Daisy Outdoor Products Service Department. CO2 CHARACTERISTICS There are occasions when a CO2 pistol may be subjected to abnormal conditions that can produce effects on the pistol’s performance.