Installation manual
English 25
: CONNECTOR
3D027501-1 FH35 • 50 • 60 • 71 • 100 • 125BVE, FH71 • 100 • 125BV1S, FH35 • 45 • 60BJV1, FH35 • 45 • 60BZV1
33A
A1P
A2P
C1R
F1U
HAP
M1A
M1F
Q1F
R1T
R2T
RyA
RyC
RyP
SS1
X1M
X2M
CD
PC
LIMIT SWITCH (SWING FLAP)
PRINTED CIRCUIT BOARD
PRINTED CIRCUIT BOARD
(TRANSFORMER 220-240V/16V)
CAPACITOR (M1F)
FUSE (250V,5A)
LIGHT EMITTING DIODE
(SERVICE MONITOR GREEN)
MOTOR (SWING FLAP)
MOTOR (INDOOR FAN)
THERMO SWITCH
(M1F EMBEDDED)
THERMISTOR (AIR)
THERMISTOR (COIL)
MAGNETIC RELAY (M1A)
MAGNETIC RELAY
(OUTDOOR UNIT COMPRESSOR)
MAGNETIC RELAY (M1P)
SELECTOR SWITCH
(EMERGENCY)
TERMINAL STRIP
TERMINAL STRIP
CURRENT DETECT CIRCUIT
PHASE CONTROL CIRCUIT
WIRED REMOTE CONTROLLER
CONNECTOR FOR OPTIONAL PARTS
WIRELESS REMOTE CONTROLLER
(RECEIVER/DISPLAY UNIT)
R1T
SS1
THERMISTOR (AIR)
SELECTOR SWITCH (MAIN/SUB)
A3P
A4P
BS
PRINTED CIRCUIT BOARD
PRINTED CIRCUIT BOARD
PUSH BUTTON (ON/OFF)
H1P
H2P
H3P
H4P
SS1
SS2
LIGHT EMITTING DIODE
(ON-RED)
LIGHT EMITTING DIODE
(TIMER-GREEN)
LIGHT EMITTING DIODE
(FILTER SIGN-RED)
LIGHT EMITTING DIODE
(DEFROST-ORANGE)
SELECTOR SWITCH
(MAIN/SUB)
SELECTOR SWITCH
(WIRELESS ADDRESS SET)
X15A
X25A
X30A
X33A
X35A
CONNECTOR
(FLOAT SWITCH)
CONNECTOR
(DRAIN PUMP)
CONNECTOR
(INTERFACE ADAPTOR FOR
SKY AIR SERIES)
CONNECTOR
(ADAPTOR FOR WIRING)
CONNECTOR
(GROUP CONTROL ADAPTOR)
1-RED 2-WHITE 3-BLACK
2. : FIELD WIRING
3. IN CASE USING CENTRAL REMOTE CONTROLLER, CONNECT IT TO THE UNIT IN ACCORDANCE WITH THE ATTACHED
INSTALLATION MANUAL.
4. X24A IS CONNECTED WHEN THE WIRELESS REMOTE CONTROLLER KIT IS BEING USED.
5. REMOTE CONTROLLER MODEL VARIES ACCORDING TO THE COMBINATION SYSTEM, CONFIRM ENGINEERING MATERIALS
AND CATALOGS, ETC. BEFORE CONNECTING.
6. IN CASE INSTALLING THE DRAIN PUMP, REMOVE THE JUMPER CONNECTOR OF X15A AND EXECUTE THE ADDITIONAL
WIRING FOR FLOAT SWITCH AND DRAIN PUMP.
7. GROUND THE SHIELD OF THE REMOTE CONTROLLER CORD TO THE INDOOR UNIT OF THE FH-BVE TYPE.
8. SYMBOLS SHOW AS FOLLOWS: RED: RED BLK: BLACK WHT: WHITE YLW: YELLOW PRP:PURPLE GRY: GRAY
BLU: BLUE
9. CONFIRM THE METHOD OF SETTING THE SELECTOR SWITCH (SS1) BY INSTALLATION MANUAL AND ENGINEERING
MATERIALS, ETC.
: TERMINAL
,
1.
NOTES)
1
2
10
9
2
3
7
10
11
WIRING DIAGRAM
Fig.34
01_EN_3PN06588-3H.fm Page 25 Monday, April 6, 2009 7:52 PM