Specifications

ESIE02–01 Disassembly and Maintenance: Indoor Units
Part 5 – Disassembly and Maintenance 5–49
3
5
1
5
Components The table below contains the components of the exploded view.
No. Component No. Component No. Component
B1 Evaporator assy E13 Wire harness (fan motor) F10.1 Insulation tube
B1.1 Distributor E14 Wire harness (swing motor) F10.2 Vertical vane air discharge
B1.2 Union joint (gas line) E15 Thermistor F10.2.1 Set plate vertical vane
B1.3 Union joint (liquid line) E16 Wire clip F10.2.2 Vertical van air discharge
B1.4 Flare nut E17 Wire clip F10.2.3 Connect. bar vertical vane
B1.5 Flare nut E18 Lock metal F10.3 Cap drain socket
B1.6 Retainer thermistor E19 Clamp F11 Supporter horizontal vane
C1 Fan assy E20 Bush thermistor F12 Horizontal vane assy
C1.1 Top plate fan assy E21 Sound absorbing material F12.1 Horizontal vane
C1.2 Fan housing E21 Sound absorbing material F12.2 Rod horizontal vane
C1.3 Fan housing F1 Top plate assy F12.3 Rod horizontal vane
C1.4 Fan rotor F2 Bottom plate assy F12.4 Rod horizontal vane
C1.4.1 Hexagon socket screw F2.1 Name plate assy F13 Decorative plate
C1.5 Fan rotor F2.1.1 Housing signal receiver F14 Air suction grille assy
C1.5.1 Hexagon socket screw F2.1.2 DAIKIN name plate F14.1 Air suction grille
C1.6 Fan motor F3 Side plate assy (right) F14.2 Fixture air suction grille
C1.7 Lock metal fan motor F3.1 Side plate (right) F14.3 Hinge air suction grille
C1.8 Motor base F3.2 Swing motor assy F15 Side plate assy
C1.9 Fan shaft assy F3.3 Set plate swing motor F16 Side plate assy
C1.10 Coupling fan shaft F3.4 Connecting arm horizontal
vane
F16.1 Cover side plate
C1.11 Fan bearing F3.5 Crank air swing F17 Blind plate piping hole
C1.12 Bearing holder F3.6 Bearing horizontal vane F18 Blind plate piping hole
C1.13 Set plate bearing holder F3.7 Heat insulation material F19 Wire clip
C1.14 Wire clip F3.8 Heat insulation material F20 Set plate drain pan
C2 Air filter F3.9 Heat insulation material F21 Supporter fan
E1 Electronic components assy F3.10 Heat insulation material F22 Retainer
E2 Switch box F3.11 Sealer F23 Air guide plate
E3 Cover switch box F3.12 Lock metal F24 Heat insulation cover piping
hole
E4 Power transformer F3.13 Wire clip F25 Insulation cover piping hole
E5 Printed circuit F4 Side plate assy F27 Protector heat exchanger
E5.1 Printed circuit (control unit) F4.1 Side plate (left) F28 Heat insulation cover
E5.1.1 Air thermistor F4.2 Bearing horizontal vane F29 Heat insulation cover
E5.1.2 Connector F4.3 Heat insulation material F30 Suspension bolt
E5.2 Capacity control adaptor F4.4 Heat insulation material K1 Drain hose
E6 Platic case F4.5 Heat insulation material K2 Hose band
E7 Capacitor fan motor F5 Hook metal K3 Insulation tube (liquid line)
E8 Terminal block F6 Hook metal K4 Insulation tube (gas line)
E9 Terminal block F7 Side plate heat exchanger K5 Sealer
E10 Wire harness (transmission) F8 Retainer K6 Sealer
E11 Wire harness (remote con-
trol)
F9 Set plate drain pan K7 Operation manual
E12 Wire harness (feed back) F10 Drain pan assy —