Installation manual

ManualsBrandsDaikin ManualsHeat PumpEBHQ011AA6W1

Installation manual

E(D/B)(H/L)Q011~016AA6V3+W1

Unit for air to water heat pump system

4PW51121-1A

Precautions on wiring of power supply

■ Use a round crimp-style terminal for connection to the power

supply terminal board. In case it cannot be used due to

unavoidable reasons, be sure to observe the following

instruction.

- Do not connect wires of different gauge to the same power

supply terminal. (Looseness in the connection may cause

overheating.)

- When connecting wires of the same gauge, connect them

according to the below ﬁgure.

■ Use the correct screwdriver to tighten the terminal screws.

Small screwdrivers can damage the screw head and prevent

appropriate tightening.

■ Over-tightening the terminal screws can damage the screws.

■ See the table below for tightening torques for the terminal

screws.

■ Attach an earth leakage circuit breaker and fuse to the power

supply line.

■ In wiring, make certain that prescribed wires are used, carry out

complete connections, and ﬁx the wires so that outside forces

are not applied to the terminals.

Speciﬁcations of standard wiring components

Door 1: compressor compartment and electrical parts: X1M

For V3 model: Equipment complying with EN/IEC 61000-3-12

(European/International Technical Standard setting the limits for

harmonic currents produced by equipment connected to public

low-voltage systems with input current >16 A and ≤75 A per phase.)

The wiring diagram can be found on the inside of the front plate of the

unit.

Connection of the backup heater power supply

Power circuit and cable requirements

This power circuit must be protected with the required safety devices

according to local and national regulations.

Select the power cable in accordance with relevant local and national

regulations. For the maximum running current of the backup heater,

refer to the table below.

Door 2: electrical parts of the hydraulic compartment: X10M

(1)(2)

Tightening torque (N•m)

M4 (X1M) 1.2~1.8

M5 (X1M) 2.0~3.0

M5 (EARTH) 3.0~4.0

V3 W1

Minimum circuit amps (MCA)

(a)

(a) Stated values are maximum values (see electrical data of combination with

indoor unit for exact values).

28.2 13.5

Recommended ﬁeld fuse 32 A 20 A

Wire type

(b)

(b) Only in protected pipes, use H07RN-F when protected pipes are not used.

H05VV-U3G H05VV-U5G

Size Wiring size must comply with the

applicable local and national code

Wire type of wiring between the units H05VV-U4G2.5

NOTE

The earth leakage circuit breaker must be a

high-speed type breaker of 30 mA (<0.1 s).

123

1 Round pressure terminal

2 Cut out section

3 Cup washer

1~ 50 Hz

230 V

3N~ 50 Hz

400 V

L1 L3L2

L1 L3

X1MX1M

1 Earth leakage circuit

breaker

2 Fuse

■ Be sure to use a dedicated power circuit for the

backup heater. Never use a power circuit shared by

another appliance.

■ Use one and same dedicated power supply for the

unit, backup heater and booster heater (domestic hot

water tank).

Model

Backup heater

capacity

Backup heater

nominal voltage

Maximum

running current

max

(Ω)

(a) (b)

(a) Equipment complying with EN/IEC 61000-3-12

(1)

(b) This equipment complies with EN/IEC 61000-3-11

(2)

provided that the system

impedance Z

sys

is less than or equal to Z

max

at the interface point between the

user's supply and the public system. It is the responsibility of the installer or user

of the equipment to ensure, by consultation with the distribution network operator

if necessary, that the equipment is connected only to a supply with a system

impedance Z

sys

less than or equal to Z

max

6 kW 1x 230 V 26 A 0.29

W1 6 kW 3x 400 V 8.6 A —

(c)

3 kW 1x 230 V 13 A —

W1 2 kW 3x 400 V 5.0 A —

(1) European/International Technical Standard setting the limits for harmonic

currents produced by equipment connected to public low-voltage systems

with input current >16 A and ≤75 A per phase.

(2) European/International Technical Standard setting the limits for voltage

changes, voltage ﬂuctuations and ﬂicker in public low-voltage supply

systems for equipment with rated current ≤75 A.