Specifications
Installation Manual ED01-505
22 Room Air Conditioners D-Series
CHOOSING A SITE
The indoor unit should be sited in a place where:
•
the restrictions on installation specified in the
indoor unit installation drawings are met,
•
both air intake and exhaust have clear paths of air,
•
the unit is not in the path of direct sunlight,
•
the unit is away from the source of heat or steam,
•
there is no source of machine oil vapour (this may
shorten indoor unit life),
•
cool air is circulated throughout the room,
•
the unit is away from electronic ignition type
fluorescent lamps (inverter or rapid start type) as
they may shorten the remote controller range,
•
the unit is at least 1 metre away from any television
or radio set (unit may cause interference with the
picture or sound)
•
install at the recommended height (1.8m).
• Before choosing the installation site, obtain user approval.
Indoor unit
The outdoor unit should be sited in a place where:
•
the restrictions on installation specified in the outdoor unit installation diagram are met,
•
drain water causes no trouble or problem in particular,
•
both air intake and exhaust have clear paths of air (they should be free of snow in
snowy districts),
•
the unit is in a clear path of air but not directly exposed to rain, strong winds, or direct
sunlight,
•
there is no fear of inflammable gas leakage,
•
the unit is no directly exposed to salt, sulfidized gases, or machine oil vapour (they
may shorten outdoor unit life).
•
operation noise or hot air flow does not cause trouble to neighbours,
•
the unit is at least 3 metres away from any television or radio antenna.
Outdoor unit
Indoor unit
•
Turn on all the fluorescent lamps in the room, if any, and find the site where remote
control signals are properly received by the indoor unit (within 7 metres).
Wireless Remote Controller
ACCESSORIES
A
A
Mounting plate
1
C
Air purifying filter with
photocatalytic deodorizing function
2
D
Wireless remote controller
1
E
Remote controller holder
~
1
G
AAA dry-cell batteries
2
H
Indoor unit fixing screw
M4 × 12L
2
K
Operation manual
1
1
L
L
Installation manual
B
Mounting plate fixing
screw M4 × 25L
6
F
Fixing screw for remote controller
holder
M3 × 20L
2
J
Insulation tape
1
INSTALLATION TIPS
1. Removing and installing front panel.
• Removal method
Hook fingers on the panel protrusions on the left and right of the main body,
and open until the panel stops. Slide the front panel sideways to disengage
the rotating shaft. Then pull the front
panel toward you to remove it.
• Installation method
Align the tabs of the front panel with the
grooves, and push all the way in. Then close
slowly. Push the center of the lower surface
of the panel firmly to engage the tabs.
2. Removing and installing front grille.
• Removal method
1) Remove front panel to remove the air filter.
2) Remove the front grille.
3) In front of the mark of the front grille,
there are 3 upper hooks. Lightly pull the
front grille toward you with one hand, and
push down on the hooks with the fingers of
your other hand.
mark area
(3 locations)
Upper hook
Lightly pull the front
grille toward you with
one hand, and push
down on the hooks with
the fingers of your other
hand. (3 locations)
Push
down.
Upper hook
Upper hook
<When there is no work space because the unit is close to ceiling>
Be sure to wear protection gloves.
Caution
Place both hands under the center of the front
grille, and while pushing up, pull it toward you.
• Installation method
1) Install the front grille and firmly engage the upper hooks (3 locations).
2) Install 2screws of the front grille.
3) Install the air filter and then mount the front panel.
3. How to set the different
addresses.
When two indoor units are
installed in one room, the two
wireless remote controllers
can be set for different
addresses.
1) Remove the front grille.
(2 screws)
2) Remove the electrical
wiring box. (1 screw)
3) Remove the metal plate
electrical wiring cover.
(3 tabs)
4)
Cut the address jumper (JA)
on the printed circuit board.
5) Cut the address jumper
(J4) in the remote controller.
Push the
rotating shaft
of the front
panel into the
groove.
ADDRESS
J4
EXIST
CUT
1
2
J4
Screw
Address
JA
Address
JA
EXIST
1
CUT 2
tab(3)
Metal
cover
PCB
Electrical
wiring box
1) Push up.
2) Pull toward you.