Dahua Panoramic + PTZ Network Camera Web3.0 Operation Manual Version 1.0.0 ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.
Table of Contents 1 2 3 4 Product Introduction ...................................................................................................... 1 1.1 Product Overview.............................................................................................. 1 1.2 Function Features ............................................................................................. 2 Basic Config ............................................................................................................
5 4.2.12 Set QoS Parameter ............................................................................ 82 4.3 Set PTZ Function ............................................................................................ 83 4.3.1 Set Preset........................................................................................... 83 Step 2 ......................................................................................................................... 84 4.3.2 Set Tour..............................
5.4 5.5 5.6 5.7 5.3.1 Backup Device Config Info ............................................................... 179 5.3.2 Recover Device Config Info .............................................................. 180 5.3.3 Default .............................................................................................. 181 Upgrade ........................................................................................................ 181 Version .........................................................
Important The following functions are for reference only. Some series products may not support all the functions listed below.
1 Product Introduction 1.1 Product Overview The product series is able to provide video preview, record, smart track and intelligent behavior analytics and so on based on the requirements of detail tracking, panoramic monitoring and large scene monitoring of various industries.
1.2 Function Features Realtime Monitoring Function Live PTZ control Talk Local snapshot Local record others Record Function Scheduled record Video playback and download Picture playback Alarm record Alarm linkage Note Supports preview panoramic camera image and tracking speed dome image at the same time. It can monitor panorama via panoramic camera, meanwhile it can check details via manual tracking or intelligent activated positioning by tracking speed dome. Supports preview mode switch.
Set alarm prompt mode or voice according to alarm type. Check alarm information. User Management Function User group management User Management Modify password Event Management Function Smart Track Video Detection Audio Detection IVS Note Support to add, modify and delete new user group. Support to manage user authority according to user group. Support to add, modify and delete users. Support to set user authority. Support to modify user password. Note Support smart track between bullet and speed dome.
Function Abnormity Note Supports SD card abnormity, network abnormity and illegal access detection. It supports linked relay-out and send email when SD card abnormity or illegal access alarm happens. It supports linked record and relay-out when network abnormity alarm happens.
2 Basic Config 2.1 Modify IP Address The default IP address of all the devices is 192.168.1.108, please modify device IP address according to network planning for the first use or during network adjustment. You can modify device IP address individually or in batch via ConfigTool, you can also log in WEB client to modify the device IP address. You can modify device IP address individually when there are less devices or the device login password is not the same.
Figure 2-1 Step 3 Set the device network segment, login user name and password, and then click OK. The system will display the searched devices after searching completes. Note The default username and password is admin and admin respectively. Step 4 Click the corresponding of the device whose IP needs to be modified. The system will pop out a dialog box of Modify IP, which is shown in Figure 2-2.
Step 5 Select the mode of setting IP address according to the actual situation. DHCP: Set mode as DHCP when there is DHCP server in the network, then the device will automatically acquire IP address from DHCP server. Manual mode: Set mode as Static and fill in the Target IP, Subnet Mask and Gateway, and then the device IP address is modified into the IP address which has been set. Step 6 Click OK to complete modification. 2.1.
The system will pop out a dialog box of Modify IP, which is shown in Figure 2-4. Figure 2-4 Step 5 Select the mode of setting IP address according to the actual situation. DHCP: Set mode as DHCP when there is DHCP server in the network, then the device will automatically acquire IP address from DHCP server. Manual mode: Set mode as Static and fill in the Start IP, Subnet Mask and Gateway, and then the device IP address will be modified from Start IP sequentially.
Graphics Card Intel HD Graphics and higher Internal Storage 2GB and higher Monitor 1024×768 and higher Browser Internet Explorer 8/9/10/11 Table 2-1 Operation Steps Step 1 Open browser, input camera IP address into the address bar and click Enter button. The system will display Login interface after it is successfully connected, which is shown in Figure 2-5. Figure 2-5 Step 2 Input Username and Password, click Login.
Figure 2-6 Note Click the Logout button on the upper right corner to log out the system. 2.3 Modify User Password Please make sure to modify the default password of the device and modify password regularly in order to guarantee device security. Meanwhile it is recommended to modify the password with high complexity. Step 1 Select "Setup > System > Account > User" and the system will display the interface of User Name, which is shown in Figure 2-7.
Figure 2-7 Step 2 Click . The system will pop out the dialogue box of Modify User. Step 3 Select Modify Password. The system will display the interface which is shown in Figure 2-8.
Figure 2-8 Step 4 Enter Old Password, New Password and Confirm Password. Step 5 Click Save to complete password modification.
3 General Operation 3.1 Live Users can implement a series of operations such as Live, Snapshot and Record etc. upon realtime monitoring image on the Live interface. Note Different devices may have different functions, please refer to the actual interface for more details. Double click the image and the image of this channel will be full screen displayed, double click or press Esc button, the image will be recovered to original size. 3.1.
SN 1 Name System menu 2 Code setting 3 Video window function PTZ control Video window adjust Switch stream 4 5 6 Note Click the function name on the system menu column to enter corresponding config interface. Stream media protocol, types of network transmission protocol, including TCP, UDP and multicast. Please refer to "3.1.2 Video Window Function" for more details. Please refer to "3.1.3.5 PTZ Control" for more details. Please refer to "3.1.3 Video Window Adjust" for more details.
SN 2 Name Regional Focus Gesture 3 Relay-out 4 Digital Zoom 5 6 7 Snapshot Triple Snapshot Record 8 9 Manual Track Audio 10 Talk 11 12 Help Note It can realize auto focus in the selected area of the tracking speed dome. Select channel image of the tracking speed dome, click the icon and click or select randomly on the channel image of the tracking speed dome, and then the speed dome can realize auto focus upon the selected region.
Figure 3-3 3.1.3.1 Local Image Adjustment It is to adjust the brightness, contrast, hue and saturation of different channel video images on the local WEB end. Note Please refer to 4.1.1 Camera for more details about the operation of actual image parameter adjustment. Select channel image, click and it will display image adjustment interface on the right of preview interface, which is shown in Figure 3-4.
Click and the channel image will be displayed with full screen. In full screen mode, double click the channel image or press Esc button to exit full screen display. 3.1.3.3 Adjust Fluency It is to adjust the fluency of channel image. Select the channel image, click to select fluency level, it supports realtime, general and fluency. 3.1.3.4 Intelligent Rules Display It is to control video image display or disable rule info. It is enabled by factory default.
Figure 3-5 SN 1 2 Function Quick Position Direction Button Speed 3 Note It is the function of quick position. Use mouse to draw a box in the monitoring image of tracking speed dome, and the PTZ will quickly position to the scene. It supports 8 directions, which are up, down, left, right, upper left, upper right, lower left and lower right. It is mainly used for speed operation, the bigger the step length is, the faster the speed becomes. The step length is only valid to PTZ direction control.
Single picture: Click and select the channel which needs to be displayed, support to select panoramic camera 1, panoramic camera 2 or tracking speed dome. Double picture: Click and the tracking speed dome is displayed by default, select panoramic camera 1 or panoramic camera 2.
Figure 3-6 3.2.1 Video Playback Video playback includes interface introduction, function column, playback video, video clip and aux function. 3.2.1.1 Interface Introduction It is to play video according to the requirement. Select file type as "dav", and the system will display the interface of video playback, which is shown in Figure 3-7, refer to Table 3-5 for more details.
Figure 3-7 SN Function 1 Play control bar 2 Volume adjustment bar 3 Rule info bar 4 Record type Note Play control button, refer to "3.2.1.2 Play Control Bar" for more details. Control the volume during playback, which includes following two states: , it means mute state. , it means voice broadcast state, volume can be adjusted. After enabling "Rule Info", the preview interface will display intelligent rules and object detection box. It is enabled by default.
SN Function 5 Progress bar 6 Progress bar time format 7 Video cut bar 8 9 Playback file bar Aux function bar Note It is to display the record type and its period. Click some spot in the color area, then it will begin to playback from the time point. Different record types mean different color, please refer to record type selection bar for corresponding relations. It includes 、 、 和 four types of format.. Take for example, it means the whole progress bar is 24 hours.
Step 2 Select the channel which needs to playback video, set "File Type" as dav", "Data Source" as "SD card", which is shown in Figure 3-9. File type includes dav and jpg, "dav" means video playback and "jpg" means picture playback. Figure 3-9 Step 3 Select the month and year of the video which needs to be checked, click the date with blue background. The system will display the record file progress bar with color. Note Display the date with blue background, it means there is record file on this date.
Click the in the file list, the record file of the selected date will be displayed in the list, double click the file in the list, which is shown in Figure 3-11. The system plays the double-clicked file, and at the same time it shown file size, begin time and end time. Please refer to Table 3-7 for more details. Figure 3-11 Operation Note Search Input begin time and end time, click . Search all the record files between begin time and end time.
Operation Note The system fails to support download and play video at the same time. Back Click to return to calendar interface. Table 3-7 3.2.1.4 Video Clip Clip some piece of video and save it to the designated storage path, which is shown in Figure 3-12. Figure 3-12 Step 1 Select "Record Format" as "dav" or "mp4". Step 2 Click on the progress bar and select the begin tine of cut video, click and begin clipping. Step 3 Click to select end time of cut video, click to finish clipping.
Table 3-8 3.2.2 Picture Playback Picture includes function bar of interface and playback picture file. 3.2.2.1 Interface Introduction Select "File Type" as "jpg", the system will display the interface of "Picture Playback", which is shown in Figure 3-13. Figure 3-13 SN Function 1 Play control bar 2 3 Snapshot type selection bar Playback file bar Note It includes following two types: , default status icon, it means pause or not play picture, click the icon to play picture.
It is to inquire and play snapshot pictures according to requirements. Step 1 Select the snapshot type which needs to be checked in the "Snapshot Type Selection Bar', which is shown in Figure 3-14. Figure 3-14 Step 2 Select the channel which needs to playback pictures, set "File Type" as "jpg", which is shown in Figure 3-15. File type includes dav and jpg, "dav" means video playback, "jpg" means picture playback.
The system will play the double-clicked file. Please refer to Table 3-10 for more details. Figure 3-16 Operation Note Search Input begin time and end time, click . Check all the picture files between start time and end time. Download Click , the file will be downloaded to local. Note Download operation may be different according to different browsers, please refer to the actual brower for more details. Return Click to return to calendar interface. Table 3-10 3.
It has to understand the alarm type and the precondition which generates event, please refer to Table 3-11 for more details. Alarm Note Precondition type Motion It generates alarm when it It has enabled the function of motion Detect detects there is moving object detection, please refer to "4.4.2.1 Set Motion in the video image. Detection" for more details. Disk Full It generates alarm when It has enabled SD card capacity warning remaining capacity of SD card detection function, please refer to "4.4.10.
Figure 3-17 Step 2 Select alarm type. Step 3 Select "Prompt", the system will prompt and record alarm info according to actual situation. When the subscribed alarm event triggers, the system is not on the "Alarm" interface, then it will show on the "Alarm" tab, and it will record alarm info automatically, the icon will disappear when clicking "Alarm" tab.
4 Config 4.1 Camera Setup It is to set the camera, video and audio conditions, which is to guarantee normal monitoring for the device. Note Different devices may have different functions, please refer to the actual interface for more details. 4.1.1 Set Camera Condition 4.1.1.1 Set Camera Parameter It is to set or check the camera parameters of tracking speed dome and panorama camera. It will take tracking speed dome as an example to introduce the config of camera parameters.
Figure 4-1 Figure 4-2 Please refer to Table 4-1 for more details about camera parameters.
Parameter Config File Image Exposure Backlight WB Day/Night Zoom&Focus Defog Default Note It is to set the config mode of camera condition, including general, day and night. It is to set the camera image parameter, including brightness, contrast, saturation, chroma CNT, sharpness and Gamma etc. It is to set the exposure mode of camera, including auto, manual, shutter priority, gain priority and iris priority. It is to set backlight mode of camera, including BLC, HLC, WDR and off.
Step 2 It is to set image parameters, please refer to Table 4-2 for more details about parameter description. Parameter Note Brightness It is to adjust image overall brightness via linear adjustment mode. The bigger the value is, the brighter the image becomes; the smaller the value is, the darker the image becomes. It is to adjust image contrast. The bigger the value is, the bigger the brightness Contrast contrast becomes, and on the contrary it becomes smaller.
Figure 4-4 Step 2 It is to set exposure parameter, please refer to Table 4-3 for parameter details. Parameter Note 50Hz: When the current is 50Hz, system can auto adjust the exposure according to the environment brightness in case there is any stripe in the image. Anti-flicker 60Hz: When the current is 60Hz, system can auto adjust the exposure according to the environment brightness in case there is any stripe in the image.
Parameter Note It is to set exposure mode of the camera. Note: When “Anti-flicker” is set as “Outdor”, the “exposure mode” can be set as “shutter priority”, “iris priority” or "gain priority" mode. Different devices have different exposure modes; please refer to the actual interface. It includes the following options: Auto: It can auto adjust the image brightness according to the environment.
Table 4-3 Step 3 Click "Save" to complete the setting. 4.1.1.1.3 Set Backlight Mode Backlight mode includes BLC, WDR and HLC. BLC: it can avoid cucoloris phenomenon of the darker area in the backlight environment. WDR: It can suppress the overbright area and compensate darker area by enabling WDR, which can make the overall image clear. HLC: It is to weaken the high light, which can be applied in the areas such as toll gate, entrance and exit of the parking lot and etc.
There might be video loss of a few seconds during the process when the camera is switched from non WDR mode to WDR mode. Backlight Mode Note The system can make exposure automatically according to the BLC environment, which is to make the image in the darkest area clear to be seen.
Step 2 It is to set WB mode, please refer to Table 4-5 for more details. WB Mode Note The system can make white balance compensation upon different light Auto environments automatically, which is to make the image color normal. The system can implement general white balance compensation upon indoor Indoor light, which is to make image color normal.
Figure 4-7 Step 2 It is to set day/night mode parameter, please refer to Table 4-6 for more details. Parameter Note Mode The camera image is displayed as color or Day&Night mode. Note "Mode" setting is not affected by the setting of "Config File". Color: The camera image is displayed as color image. Auto: The camera auto select to display color image or black & white image according to the brightness of monitoring image. Black & White: The camera image is displayed as black & white image.
Figure 4-8 Step 2 It is to set zoom and focus parameter, please refer to Table 4-7 for more details. Parameter Note Digital Zoom Select "ON" to enable digital zoom. When optical zoom reaches max, it can continue to implement digital zoom after it is enabled. Zoom Speed It is the zoom speed of the camera, the bigger the value is, the faster the zoom speed becomes. Mode Camera focus mode.
Step 3 Click "Save" to complete setting. Note Click "Lens Init" to implement lens initialization for the lens of tracking speed dome, at this moment the device lens will be stretched, which means correction upon lens zoom and focus. 4.1.1.1.7 Set Defog Mode The image quality will become lower when the device is located in the environment with fog and haze, it can enable defog function to adjust the image definition.
Step 3 Click "Save" to complete setting. 4.1.1.2 Profile Management For config profile management, it can select "General", "Full Time" and "Schedule". Step 1 Select "Setup > Camera > Conditions > Profile Management" and the system will display the interface of "Profile Management". Step 2 Select channel. When the "Channel" is set as "1", it is to manage the config file of tracking speed dome. When the "Channel" is set as "2" or "3", it is to manage the config file of panorama camera.
Figure 4-11 When the "Profile Management" is set as "Schedule", it can set some period as day and set some other period as night, if it sets 8:00～17:00 as day, then 0:00~8:00 and 18:00～24:00 are considered as night, the system will implement monitoring by adopting corresponding config in different time. Figure 4-12 Step 4 Click "Save" to complete setting. 4.1.
4.1.2.1 Set Video It is to set the video stream parameters of tracking speed dome and panorama camera, which includes stream type, encode mode, resolution, frame rate, bit rate type, bit rate, I frame interval, SVC and watermark setting etc. Step 1 Select "Setup > Camera > Video > Video" and the system will display the interface of "Video", which is shown in Figure 4-13. Figure 4-13 Step 2 Select channel. When the "Channel" is set as "1", it is to set the video stream parameters of tracking speed dome.
Parameter Function Encode mode It is the encode mode of video. H.264: Main Profile encode mode. H.264B: Baseline Profile encode mode. H.264H: High Profile encode mode. MJPEG: In this encode mode, the video needs large bit stream to guarantee the video definition. You can use the max bit stream value in the recommended bit to get the better video output effect. H.264: Main Profile encode mode. Enable smart codec to improve image compression performance and reduce storage space.
Parameter Function Stream Upper Limit When the "Bit Rate Type" is set as "VBR", you can set the parameter. It is to select the stream upper limit according to "Reference Bit Rate", the stream will change according to the monitoring scene, but the max stream value changes around the stream value which has been set. I Frame Interval The number of P frame between two I frames, the range of I frame interval changes according to the different frame rate.
Figure 4-14 Step 2 Select channel. When the "Channel" is set as "1", it can set the snapshot parameter of tracking speed dome. When the "Channel" is set as "2" or "3", it can set the snapshot parameter of panorama camera. Step 3 It is to set snapshot, please refer to Table 4-10 for more details. Parameter Function Snapshot type There are two modes: General (schedule) and Event (activation). General snapshot means making snapshot within the range which is set by schedule.
It is to set the video overlay info of both tracking speed dome and panorama camera, which includes privacy mask, channel title, time title, text overlay, OSD info, font and picture overlay. 4.1.2.3.1 Set Privacy Masking It can set privacy mask when it needs to protect privacy of some area on the video image. Note Only panorama camera supports privacy mask function. Step 1 Select "Setup > Camera > Video > Overlay" and the system will display the interface of "Overlay". Step 2 Set "Channel" as "2" or "3".
4.1.2.3.2 Set Channel Title It can set channel title when it needs to display channel title in the video image. Step 1 Select "Setup > Camera > Video > Overlay" and the system will display the interface of "Overlay". Step 2 Select channel. When "Channel" is set as "1", it is to set video overlay of tracking speed dome. When "Channel" is set as "2" or "3", it is to set video overlay of panorama camera.
Select "Setup > Camera > Video > Overlay" and the system will display the interface of "Overlay". Step 2 Select channel. When the "Channel" is set as "1", it is to set the video overlay of tracking speed dome. When the "Channel" is set as "2" or "3", it is to set the video overlay of panorama camera. Step 3 Click "Time Title" and the system will display the interface of "Time Title", which is shown in Figure 4-17. Figure 4-17 Step 4 Select "Enable" and time info will be displayed in the video image.
Step 1 Select "Setup > Camera > Video > Overlay" and the system will display the interface of "overlay". Step 2 Set the "Channel" as "2" or "3". Step 3 Click "Text Overlay" and the system will display the interface of "Text Overlay", which is shown in Figure 4-18. Figure 4-18 Step 4 It is to set temperature, RS485 and text overlay info according to the actual requirements. Select corresponding "Enable" of temperature, and select the display mode of temperature.
4.1.2.3.5 Set Picture Overlay It can set picture overlay when it needs to display picture info in the video image. Note Text overlay and picture overlay can't be enabled at the same time. Step 1 Select "Setup > Camera > Video > Overlay" and the system will display the interface of "Video Overlay". Step 2 Select channel. When the "Channel" is set as "1", it is to set video overlay of tracking speed dome. When the "Channel" is set as '2" or "3", it is to set the video overlay of panorama camera.
Step 6 Click "Save" to complete setting. 4.1.2.3.6 Set Privacy Mask It can set privacy mask when it needs to protect the privacy of some areas in the image. Note Only tracking speed dome supports privacy mask function. The config of privacy mask takes effect realtime. Step 1 Select "Setup > Camera > Video > overlay" and the system will display the interface of "Overlay". Step 2 Set "Channel" as '1".
Adjust preview image to proper location via PTZ, select proper color and click "Draw", press the left button and drag out rectangular box in the preview image. Note Select "SN" and click "Go to", then the PTZ camera will move to the corresponding location of setting privacy mask. 4.1.2.3.7 Set OSD Info It can set OSD info when it needs to display preset, PTZ coordinates, zoom, pattern, text and so on. Note Only tracking speed dome supports OSD info function.
Parameter Preset Temperature Coordinates Note Select "Enable", it will display the preset name in the image when switching to the preset which has been set, such as , and it will disappear after 3 seconds. Select "Enable" and it will display internal temperature of the current device. Select "Enable" and it will display PTZ coordinates info in the image. Select "Enable" and it will display zoom info in the image, such Zoom North RS485 Text Input Text Alignment as , which means 12x zoom rate.
Figure 4-22 Step 2 Select channel. When the "Channel" is set as "1", it is to set the ROI of tracking speed dome. When the "Channel" is set as "2" or "3", it is to set the ROI of panorama camera. Step 3 Select "Enable" and it will enable ROI function. Step 4 Press left button and draw ROI area in the image, and then you can set the image quality of ROI area. Note It can set max 4 areas.
Step 1 Select "Setup > Camera > Video > Path" and the system will display the interface of "path", which is shown in Figure 4-23. Figure 4-23 Step 2 Click "browse" respectively and set the storage path of live snapshot, live record, playback snapshot, playback download and video clips. Please refer to Table 4-12 for more details. Path Note Live Live snapshot is corresponding to the snapshot of preview interface. Snapshot Default path is C:\Users\Administrator\WebDownload\LiveSnapshot.
Step 1 Select "Setup > Camera > Audio" and the system will display the interface of "Audio", which is shown in Figure 4-24. Figure 4-24 Step 2 It is to set audio parameters, please refer to Table 4-13 for more details. Parameter Note It can enable audio only when video is enabled. It will enable audio output channel 1 or audio output channel 2 after Channel 1/Channel 2 selecting "Channel 1" or "Channel 2" of main stream or sub stream area. It is to encode mode of audio, including G.711A, G.711Mu, G.
Parameter AudioIn Type Noise Filter Microphone Volume Speaker Volume Note It is the audio type which is connected to device. LineIn: The device has to externally connect to audio input source Mic: The device doesn't need to externally connect to audio input source. The system will automatically filter the noise in the environment after enabling noise filter. It is to adjust the microphone volume. Note Only some devices support microphone volume adjustment. It is to adjust the speaker volume.
Figure 4-25 Step 2 It is to set TCP/IP parameters, please refer to Table 4-14 for more details. Parameter Function Host Name It is to set current host device name. It supports max 15 characters. Ethernet Card Select the Ethernet card which needs to be configured, it is wired by default. Mode Static Manually set IP address, subnet mask and gateway. DHCP Auto acquire IP function. "IP address", "Subnet mask" and "Default gateway' can't be set when enabling DHCP.
Subnet mask and "Subnet Mask" according to the actual situation. Note The device will make legal inspection to all the IPv6 addresses, IP address and default gateway have to be in the same segment, which means that it can pass inspection as long as the field of designated length of subnet prefix has to be the same. Default gateway Make sure it has to be in the same segment with IP address according to the actual situation. Preferred DNS Server DNS server IP address.
Enable ARP/Ping to set device IP address service. Select the check box, you can use ARP/Ping command to modify or set the device IP address if you know the device MAC address. When it is enabled by default, ping packet can set device IP via specific length within 2 minutes during device reboot, the service is off 2 minutes later, the service will be closed immediately after setting IP successfully. Ping packet can’t set IP if it is not enabled. A living example of setting device IP via ARP/Ping 1.
4.2.2 Set Connection Parameter 4.2.2.1 Set Connection Port Parameter You can set the max number of ports which can be connected to device and each port value. Step 1 Select "Setup > Network > Connection > Connection" and the system will display the interface of "Connection", which is shown in Figure 4-26. Figure 4-26 Step 2 It is to set connection parameters, please refer to Table 4-15 for more details.
HTTP Port HTTP communication port, it is 80 by default. If it sets other value, then it needs to add modified port number at the address when using browser to log in. RTSP port The RTSP port number is 554 by default. Please leave it blank if using default. Users use QuickTime or VLC to play the following formats. BlackBerry supports the function as well. Real-time monitoring URL format, please require real-time RTSP media server, require channel No., and bit stream type in URL.
The camera login "Username" and "password" are both admin via ONVIF, "Port" is 80. Step 1 Select "Setup > Network > Connection > ONVIF" and the system will display the interface of "ONVIF", which is shown in Figure 4-27. Figure 4-27 Step 2 Set "Authentication" as "Enable". Step 3 Click "Save" to complete setting. 4.2.3 Set PPPoE Parameter It is to build network connection via enabling PPPoE (Point-to-Point Protocol over Ethernet) dial mode; the device will acquire a dynamic IP address of WAN.
Figure 4-28 Step 2 Select "Enable" and input PPPoE username and password. Step 3 Click "Save" to complete setting. The system prompts that it is successfully saved and it realtime displays the acquired public network IP address, users can visit the device via this IP address. 4.2.
Figure 4-29 Step 2 Select "Server Type" and configure DDNS parameters according to the practical situation. Please refer to Table 4-16 for DDNS parameter config if it selects DDNS type as "QUICK DDNS". Parameter Note It is the address of DDNS server provider, it is www.quickddns.com by Server Address default, which can't be modified. Mode It is auto by default, it can select manual as well. It is “MAC Address.dahuaddns.com” for both auto and manual default, it Domain Name can set prefix manually.
Figure 4-30 Parameter Server Type Server Address Domain Name Username Password Update Period Note It is the name and address of DDNS server, the corresponding relation is shown as follows Dyndns DDNS address is: members.dyndns.org NO-IP DDNS address is: dynupdate.no-ip.com CN99 DDNS address is: members.3322.org It is the domain name which is registered on the website of DDNS server provider Input the username and password acquired from DDNS service provider.
In order to enhance device network security and protect device data, users can set the user who is allowed to have access to the device via IP filter. White list: it can have access to the device only when the users' IP/MAC is in the white list, otherwise, it fails to have access to the device. Users are not allowed to set the device IP/MAC as white list. MAC verification is valid when the IP of device and user PC are in the same LAN.
Step 3 Select "Enable" to enable white list. Step 4 Click "Save" to complete setting. Use the IP host in the white list to log in device WEB interface, and you can log in the device successfully. 4.2.6 Set SMTP Parameter It will send email immediately when alarm, video detection, abnormal events and intelligent events happen via setting Email. Step 1 Select "Setup > Network > SMTP" and the system will display the interface of "SMTP", which is shown in Figure 4-32.
Step 2 Configure SMTP server, please refer to Table 4-19 for the config description of common email. Email Encryption SMTP Server Port Note Type Mode SSL 465 For encryption mode, it can't select "None". "SMTP" service has to be available to the Email. Password has to adopt "Authorization QQ smtp.qq.com Code", it is invalid to use both QQ login TLS 587 password and email login password. Note The authorization code is acquired when Email enables SMTP service. 465/9 Email has to enable "SMTP" service.
Parameter Function Interval It is the interval of sending emails, "0" means there is no interval for sending emails. After setting interval, when alarm, video detection and abnormal event trigger E-mail, the Email won't send E-mail immediately according to the trigger of alarm signal, but send email according to the interval of previous same event email, which is mainly applied to the phenomenon that frequent abnormal events generate a large number of emails and too much pressure for email server.
Figure 4-33 Step 2 Select "Enable" to enable UPnP function. Step 3 Select mode and check corresponding service name. UPnP consists of two mapping modes which are auto and manual. Manual mapping mode allows users to modify external port. Auto mapping mode selects unoccupied ports to complete port mapping automatically, users don't need to modify mapping. Step 4 Click "Save" to complete setting.
Operation Steps Step 1 Select "Setup > Network > SNMP" and the system will display the interface of "SNMP", which is shown in Figure 4-34 and Figure 4-35.
Figure 4-35 Step 2 Select "SNMP Version" and enable SNMP. Step 3 It is to configure SNMP parameters, please refer to Table 4-21 for more details. For Trap address, it has to fill in with IP address of PC which is installed with MG-SOFT MIB Browser, the other configs are default.
Parameter Function SNMP Version Select check box of corresponding version, and the device will deal with the info of corresponding version. Check SNMP v1, device only process v1 info. Check SNMP v2, device only process v2 info. Check SNMP v3, it can set username, password and encryption method. Server calibrate corresponding username, password and encryption method to access device and v1/v2 are unavailable. SNMP port The listening port of the proxy program of the device.
Parameter Function Encryption Password The password length is no less than 8 characters. Table 4-21 Step 4 Click "Save" to complete setting. Step 5 Check device info. 1. Run MIB Builder and MG-SOFT MIB Browser softwares. 2. Compile two MIB files via MIB Builder software. 3. Run MG-SOFT MIB Browser software and load the compiled module into the software. 4. Input the device IP which needs to be managed into the MG-SOFT MIB Browser software, select version number and check. 5.
Figure 4-36 Step 2 Select "Enable" and set server name. Step 3 Click "Save" to complete setting. It can have access to WEB interface via Safari browser in the operating system and client which support Bonjour, the steps are shown as follows: Step 1 Click the "Show All Bookmarks" of the Safari browser. Step 2 Enable "Bonjour" and it can automatically detect the devices which enable Bonjour function in the LAN. Step 3 Click to have access to the corresponding WEB page. 4.2.
Figure 4-37 Step 2 Select "Enable" of main stream or sub stream and enable multicast function. Step 3 Input multicast address and port. Multicast port is not limited while the range of multicast IP address is limited, which is shown in Figure 4-38.
All the other addresses can be used except the addresses above with specific meaning, which is shown in Figure 4-39. Figure 4-39 Step 4 Click "Save" to complete setting. Select "Protocol" as "Multicast" on the WEB preview interface, then you can monitor video image via multicast. 4.2.11 Set 802.1x Parameter It can control whether the device can be connected to LAN, besides, it can well support the requirements of network authentication, charging, safety and management.
Parameter Authentication Username Password Note PEAP (protected EAP protocol) It is the username of identity authentication, it needs to be admitted and authorized by server end. It is to set the password which is corresponding to the username. Table 4-22 Step 4 Click "Save" to complete setting. 4.2.12 Set QoS Parameter Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and jam problem and etc.
Parameter Note Realtime Monitor It is the priority level of network video monitoring data packet. Command It is the priority level of non-monitoring data packet such as device config and query etc. Table 4-23 Step 3 Click "Save" to complete setting. 4.3 Set PTZ Function Only tracking speed dome supports PTZ function setup. 4.3.
Figure 4-42 Step 2 Set preset. 1. Click "Add" to add a new preset. 2. Move the camera to the needed monitoring direction via controlling the PTZ control panel. 3. Double click the new preset title to modify title, click to complete setting. Note Click Click "Clear" to delete all the added presets. to delete the presets which are wrongly configured or not needed any more. 4.3.
Figure 4-43 Step 2 Set tour. 1. Click "Add" to add a new tour. 2. Click "Add" to add a new preset. Several clicks to add several presets. 3. Double click to select preset, and double click to set duration. 4. Double click the new tour name to modify name, click "Save" to complete setting. Note Click to delete corresponding tour and presets. Step 3 Select tour, click "Start" to start tour. Click "Stop" to stop tour. 4.3.
Select "Setup > PTZ > Function > Scan" and the system will display the interface of "Scan", which is shown in Figure 4-44. Figure 4-44 Step 2 Set scan. 1. Select scan number and set scan speed. 2. Click "Set" and the system will display "Set Left Limit" and "Set Right Limit". 3. Move the camera to the needed left limit via operating control panel, and click "Set Left Limit"; move the camera to the needed right limit, and click "Set Right Limit" to complete setting.
Figure 4-45 Step 2 Set pattern. 1. Select pattern number. 2. Click "Set" and the system will display the buttons of "Start Rec" and "Stop Rec". 3. Click "Start Rec". 4. It can control camera monitoring direction, zoom and focus via operating PTZ control panel. 5. Click "Stop Rec" to complete setting. Step 3 Select pattern number, click "Start" to enable pattern. Click "Stop" to stop pattern. 4.3.5 Enable Pan Pan means that the camera can continuously rotate 360°horizontally with a certain speed.
Figure 4-46 Step 2 Set pan speed, click "Start" and the camera starts pan. Click "Stop" to stop pan. 4.3.6 Set PTZ Speed PTZ speed means the rotation speed of the PTZ. Step 1 Select "Setup > PTZ > Function > PTZ Speed" and the system will display the interface of "PTZ Speed", which is shown in Figure 4-47.
Figure 4-47 Step 2 Select PTZ speed and complete setting. 4.3.7 Set Idle Motion Idle motion means that the camera implement the action which is set in advance if it fails to receive any valid command within specific period of time. It has to make sure the selected motion has completed config before setting idle motion. Preconditions It has set preset, tour, scan and pattern.
Figure 4-48 Step 2 Set idle motion. 1. Select "Enable" to enable idle motion. 2. Select idle motion, select the number if there is number for idle motion and set idle time. 3. Click "Save" to complete setting. 4.3.8 Set PowerUp PowerUp means the action that the camera will implement automatically after power up. Step 1 Select 'Setup > PTZ > Function > PowerUp" and the system will display the interface of "PowerUp", which is shown in Figure 4-49.
Figure 4-49 Step 2 Set PowerUp. 1. Select 'Enable" 2. Select powerup and select corresponding number if there is one. Note The system will run the last movement which lasts 20s before power off when selecting "Auto". 3. Click "Save" to complete setting. 4.3.9 Set Time Task Time task means that it implements relevant task movements within the period which has been set. Precondition It has set preset, tour, scan and pattern.
Select "Setup > PTZ > Function > Time Task" and the system will display the interface of "Time Task", which is shown in Figure 4-50. Figure 4-50 Step 2 Set time task. 1. Select "Enable" to enable time task function. 2. Click "Time Task No" to select a time task number. 3. Select corresponding time task action, the system will display the number box of corresponding action. Click "Action No" and select the corresponding number of the action. 4. Set auto home time in "AutoHome".
Figure 4-51 1. 2. 3. 4. Select "Time Task No." which has already been configured with task number. Select time task number which is to be configured in "Copy to Task No". Click "Copy". Click "Save" to complete the setting of time task. 4.3.10 PTZ Restart Restart the PTZ manually. Step 1 Select "Setup > PTZ > Function > PTZ Restart" and the system will display the interface of "PTZ Restart", which is shown in Figure 4-52.
Figure 4-52 Step 2 Click "PTZ Restart" to restart the PTZ. 4.3.11 Default Caution The function will delete all the PTZ configs implemented by users after it is enabled, please operate carefully. Step 1 Select "Setup > PTZ > Function > Default" and the system will display the interface of "Default", which is shown in Figure 4-53.
Figure 4-53 Step 2 Click "Default" and the PTZ function will be restored to default config. 4.4 Event 4.4.1 Set Smart Track After enabling linkage tracking and setting calibration parameters, the tracking speed dome will be activated to corresponding location and track the object till it is out of the monitoring range when the intelligent rules of panorama camera triggers alarm. Precondition The panorama camera has set intelligent rules of intrusion or tripwire, please refer to "4.4.
4.4.1.1 Enable Alarm Track Alarm track is off by default, smart track is valid only after enabling alarm track. Step 1 Select "Setup > Event > Smart Track > Alarm Track" and the system will display the interface of "Alarm Track", which is shown in Figure 4-54. Figure 4-54 Step 2 Click the slider to enable alarm track. 4.4.1.2 Set Calibration Parameter The device is equipped with calibration parameter when it is delivered out of factory.
Figure 4-55 Step 2 Select the lens number below in sequence (which is shown in Figure 4-56 ), add calibration point for corresponding lens video image.
1. Click and click video image to display calibration box, drag the calibration box to proper location. 2. After clicking "Position", click calibration location in the image of tracking speed dome, move the video image of tracking speed dome to the corresponding location of the calibration point. 3. Click to save calibration record. Repeat 1~3 to add at least four calibration points for video image of each lens. Step 3 Click "Save" to complete setting. 4.4.
Figure 4-57 Step 2 Select channel. When the "Channel" is set as "1", it will set the motion detection of tracking speed dome. When the "Channel" is set as '2" or "3", it will set the motion detection of panorama camera. Step 3 Select "Enable" to enable motion detection function. Step 4 It is to set motion detection area. 1. Click the "Setup" which is next to the "Area". The system will pop out the interface of "Area", which is shown in Figure 4-58.
Figure 4-58 2. Set area name, it is to set valid area of motion detection according to the actual situation, and it can set the value of sensitivity and threshold respectively. The bigger the sensitivity is, the easier it is to generate motion detection, the smaller the threshold is, the easier it is to generate motion detection; the entire video image is the valid area of motion detection by default. Note Different colors represent different areas; each area can set different detection area.
Parameter Function Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Parameter Function Snapshot Select check box and set the channel number of snapshot. The corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.5 Set path" for snapshot storage path query and setting. It needs to enable motion snapshot before enabling the function, please refer to "4.5.1.2 Snapshot Schedule" for more details. Table 4-24 Step 6 Click "Save" to complete setting. 4.4.2.
Step 2 Select channel. When the "Channel" is set as "1", it is to set the video tamper detection of tracking speed dome. When the 'Channel" is set as "2" or '3", it is to set the video tamper detection of panorama camera. Step 3 Select "Enable" to enable video tamper detection. Step 4 It is to set the parameters of video tamper detection, please refer to Table 4-25 for more details.
Parameter Function PTZ Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs. Activation operation includes preset, tour and pattern. Note It needs to set PTZ before enabling the function, please refer to "4.3 Set PTZ" for more details. Select check box and set the channel number of snapshot. The corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.
Figure 4-60 Step 2 Select channel. When the "Channel" is set as "1", it is to set the scene changing of tracking speed dome. When the 'Channel" is set as "2" or '3", it is to set the scene changing of panorama camera. Step 3 Select "Enable" to enable scene changing detection. Step 4 It is to set the parameters of scene changing, please refer to Table 4-26 for more details.
Parameter Function Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Table 4-26 Step 5 Click "Save" to complete setting. 4.4.3 Set Audio Detection Step 1 Select "Setup > Event > Audio Detection" and the system will display the interface of "Audio Detection", which is shown in Figure 4-61.
Step 2 Select audio channel. Step 3 It is to set audio detection parameters, please refer to Table 4-27 for more details. Parameter Function Enable Input Abnormal Select the check box, it will generate alarm when it detects audio input abnormity. Enable Intensity Change Select the check box, it will generate alarm when it detects there is audio intensity change and it exceeds the threshold.
Parameter Function Alarm Delay System can delay the alarm output for specified time after alarm ended. Send Email Select check box, and the system will send email to inform users when alarm occurs. Note It needs to set Email before enabling the function, please refer to "4.2.6 Set SMTP Parameter" for more details. Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs.
Figure 4-62 Step 3 Enable corresponding intelligent function according to requirements. Enable heat map or people counting function. 1. Click the slider in the to enable function switch. 2. Click heat map or people counting to enable corresponding intelligent function. The selected intelligent function will be displayed with high brightness, click the selected intelligent function to cancel it. Enable IVS or face detection function. The system enables IVS and face detection function by default. 1.
Step 1 Select "Setup > Event > Smart Plan" and the system will display the interface of "Smart Plan". Step 2 Select "Channel" as "2" or "3" and the system will display the smart plan interface of panorama camera, which is shown in Figure 4-63. Figure 4-63 Step 3 Click IVS to enable corresponding intelligent function. The selected function will be displayed with high brightness, click the selected function to cancel it. Step 4 Click "Save" to complete setting. 4.4.5 Set IVS 4.4.5.
Make sure the target appears at least over 2 seconds continuously in the field; the movement distance has to be bigger than the width of the target itself and makes sure it is no less than 15 pixels (CIF image). Try to lower the complexity of the monitoring scene analysis if it is possible; it is not advised to use IVS functions in the environment where the targets are dense and light change is very frequent.
Step 2 Select channel. When the "Channel" is set as "1", it is to set the intelligent rules of tracking speed dome. When the "Channel" is set as "2" or "3", it is to set the intelligent rules of panorama camera. Step 3 Select "Preset" and the camera will quickly move to the corresponding position of the preset. Note It needs to implement the step when it is to set the intelligent rules of tracking speed dome. Step 4 It is to configure the rule of cross fence. 1.
Click "Clear" to delete all the drawn rules. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size. Note It will alarm only when the size of target is between two filter boxes. In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box. 4. It is to set the parameters of cross fence, please refer to Table 4-28 for more details.
Parameter Note Alarm delay It means the alarm delays a period of time to stop after alarm ends. Send Email Select check box, and the system will send email to inform users when alarm occurs. Note It needs to set Email before enabling the function, please refer to "4.2.6 Set SMTP Parameter" for more details. PTZ Snapshot Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs.
Step 3 Select "Preset" and the camera will quickly move to the corresponding position of the preset. Note It needs to implement the step when it is to set the intelligent rules of tracking speed dome. Step 4 It is to configure the rule of cross fence. 1. Click , double click the new rule, set rule name, and select rule type as "Tripwire", which is shown in Figure 4-65. Figure 4-65 2.
In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box. 4. It is to set the parameters of tripwire, please refer to Table 4-29 for more details. Parameter Note Working period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
Parameter Note It needs to set Email before enabling the function, please refer to "4.2.6 Set SMTP Parameter" for more details. PTZ Snapshot Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs. Activation operation includes preset, tour and pattern. Note It needs to set PTZ before enabling the function, please refer to "4.3 Set PTZ" for more details.
It is to configure the rule of intrusion. 1. Click , double click the new rule, set rule name, and select rule type as "Intrusion", which is shown in Figure 4-66. Figure 4-66 2. Click "Draw Rule" to draw rules on the monitoring image, right click to end drawing; Note It takes some time and space from when the target appears to when the target is confirmed, therefore, it has to leave some space when drawing the warning area, don't draw rules near the blocking object.
In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box. 4. It is to set the parameters of intrusion, please refer to Table 4-30 for more details. Parameter Working period Action Direction Alarm track Note It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
Parameter Note Alarm delay It means the alarm delays a period of time to stop after alarm ends. Send Email Select check box, and the system will send email to inform users when alarm occurs. Note It needs to set Email before enabling the function, please refer to "4.2.6 Set SMTP Parameter" for more details. PTZ Snapshot Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs.
Step 3 Select "Preset" and the camera will quickly move to the corresponding position of the preset. Note It needs to implement the step when it is to set the intelligent rules of tracking speed dome. Step 4 It is to configure the rule of abandoned object. 1. Click , double click the new rule, set rule name, and select rule type as "Abandoned Object", which is shown in Figure 4-67. Figure 4-67 2.
Click "Clear" to delete all the drawn monitoring areas. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size. Note It will alarm only when the size of abandoned target is between two filter boxes. In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box. 4. It is to set the parameters of abandoned object, please refer to Table 4-31 for more details.
Parameter Note when alarm occurs. Alarm delay It means the alarm delays a period of time to stop after alarm ends. Send Email Select check box, and the system will send email to inform users when alarm occurs. Note It needs to set Email before enabling the function, please refer to "4.2.6 Set SMTP Parameter" for more details. PTZ Snapshot Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs.
It is to configure the rule of fast moving. 1. Click , double click the new rule, set rule name, and select rule type as "Fast Moving", which is shown in Figure 4-68. Figure 4-68 2. Click "Draw Rule" to draw rules on the monitoring area, right click to end drawing; Note Click "Clear" to delete all the drawn monitoring areas. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size.
Parameter Working period Sensitivity Alarm track Note It is to set the alarm period, it can enable alarm event only during the period range which has been set. 4. Click “Setup” and the system will pop out the interface of “Working Period”. 5. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Parameter PTZ Snapshot Note Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs. Activation operation includes preset, tour and pattern. Note It needs to set PTZ before enabling the function, please refer to "4.3 Set PTZ" for more details. Select check box and set the channel number of snapshot. The corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.
Figure 4-69 2. Click "Draw Rule" to draw monitoring area on the monitoring image, right click to end drawing; Note Click "Clear" to delete all the drawn monitoring areas. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size. Note It will alarm only when the size of target is between two filter boxes. In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box. 4.
Parameter Note Keep Time Alarm track You can input time numerical value or press the left mouse button to drag on the setup interface to set. Click the "Setup" of corresponding week, select the check box in front of the period on the bottom of the interface, and input time value, there are six periods to be set every day. 3. Click “Save” to complete the setup of working period. It is the shortest time from when the target stops in the detection area to when it triggers alarm.
Parameter Note Snapshot Select check box and set the channel number of snapshot. The corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.5 Set path" for snapshot storage path query and setting. It needs to enable motion snapshot before enabling the function, please refer to "4.5.1.2 Snapshot Schedule" for more details. Table 4-33 Step 5 Click 'Save" to complete setting. 4.4.5.2.
Figure 4-70 2. Click "Draw Rule" to draw monitoring area on the monitoring image, right click to end drawing; Note Click "Clear" to delete all the drawn monitoring areas. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size. Note It will alarm only when the size of crowd target is between two filter boxes. In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box.
Parameter Keep Time Sensitivity Alarm track Note 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set. Click the "Setup" of corresponding week, select the check box in front of the period on the bottom of the interface, and input time value, there are six periods to be set every day. 3.
Parameter PTZ Snapshot Note Select check box, set activation and corresponding serial number. The system will activate and move to the selected preset, tour or pattern when alarm occurs. Activation operation includes preset, tour and pattern. Note It needs to set PTZ before enabling the function, please refer to "4.3 Set PTZ" for more details. Select check box and set the channel number of snapshot. The Corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.
Figure 4-71 2. Click "Draw Rule" to draw monitoring area on the monitoring image, right click to end drawing; Note Click "Clear" to delete all the drawn monitoring areas. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size. Note It will alarm only when the size of crowd target is between two filter boxes. In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box.
Parameter Note Keep Time Alarm track You can input time numerical value or press the left mouse button to drag on the setup interface to set. Click the "Setup" of corresponding week, select the check box in front of the period on the bottom of the interface, and input time value, there are six periods to be set every day. 3. Click “Save” to complete the setup of working period. It is the shortest time from when the target is taken out of the detection area to when it triggers alarm.
Parameter Note Snapshot Select check box and set the channel number of snapshot. The Corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.5 Set path" for snapshot storage path query and setting. It needs to enable motion snapshot before enabling the function, please refer to "4.5.1.2 Snapshot Schedule" for more details. Table 4-35 Step 5 Click "Save" to complete setting. 4.4.5.2.
Figure 4-72 2. Click "Draw Rule" to draw monitoring area on the monitoring image, right click to end drawing; Note Click "Clear" to delete all the drawn monitoring areas. 3. Select max size or min size, click "Draw Target", and drag any angle of the filter box to enlarge or narrow the filter box to proper size. Note It will alarm only when the size of crowd target is between two filter boxes. In the state of drawing, select "Max Size" or "Min Size", click "Clear" to delete corresponding filtering box.
Parameter Note drag on the setup interface to set. Click the "Setup" of corresponding week, select the check box in front of the period on the bottom of the interface, and input time value, there are six periods to be set every day. 3. Click “Save” to complete the setup of working period. It is the shortest time from when the target is taken out of the detection area to when it triggers alarm.
Parameter Note Snapshot Select check box and set the channel number of snapshot. The Corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.5 Set path" for snapshot storage path query and setting. It needs to enable motion snapshot before enabling the function, please refer to "4.5.1.2 Snapshot Schedule" for more details. Table 4-36 Step 5 Click "Save" to complete setting. 4.4.5.
Figure 4-73 Step 2 Select "Preset" and the camera will quickly move to the corresponding position of the preset. Note It needs to implement the step when the device supports to select preset. Step 3 Add detect area and exclude area. 1. Click "Add Detect" and draw detection area on the monitoring image, right click to end drawing. Note Click "Add Detect" again to draw detection area again. 2. Click "Add Exclude" and draw excluded area in the detection area, right click to end drawing.
Step 4 Calibration area. 1. Click "Add Calibration" and draw calibration area in the monitoring image, right click to end drawing. 2. Select "Horizontal" and set the corresponding actual length of the horizontal ruler, and draw horizontal ruler in the calibration area. 3. Select "Vertical" and set the corresponding actual length of the vertical ruler, and draw vertical ruler in the calibration area. 4.
Step 6 Click "Save" to complete setting. 4.4.6 Set Face Detection The system will generate alarm and activate the actions which have been set when it detects human face in the video image. Precondition Please refer to "4.4.4 Set Smart Plan" for the IVS smart plan which has been set preset face detection for the tracking speed dome. Operation Steps Step 1 Select "Setup > Event > Face Detection" and the system will display the interface of "Face Detection", which is shown in Figure 4-74.
Parameter Working period Enable Face Enhancement Record Note It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Parameter Note Snapshot Select check box and set the channel number of snapshot. The Corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.5 Set path" for snapshot storage path query and setting. It needs to enable motion snapshot before enabling the function, please refer to "4.5.1.2 Snapshot Schedule" for more details. Table 4-38 Step 4 Click "Save" to complete setting. 4.4.7 Set People Counting 4.4.7.
Figure 4-75 Step 2 Select serial number of people counting in the area which needs people number statistics via PTZ control panel. Step 3 Click "Draw Rule" and press left button to draw people counting area on the monitoring image. Step 4 Select "Enable" to enable the function of people counting. Step 5 It is to configure the parameters of people counting, please refer to Table 4-39 for more details.
Parameter Rule Name Direction Flowrate Alarm Record Note range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Parameter Note Snapshot Select check box and set the channel number of snapshot. The Corresponding channel will take snapshot automatically when alarm occurs. Note Please refer to "4.1.2.5 Set path" for snapshot storage path query and setting. It needs to enable motion snapshot before enabling the function, please refer to "4.5.1.2 Snapshot Schedule" for more details. Table 4-39 Step 6 Click "Save" to complete setting. 4.4.7.2 Report It is to check the people statistics data of a certain period.
Figure 4-76 Step 2 Select the serial number of people counting which needs to be inquired. Step 3 It is to set search condition, please refer to Table 4-40 for more details. Parameter Note It is the report period and display form of people counting report, report Report Type period can select day, month or year, report display form can select bar chart or line chart. Start Time It is the start time of people counting report. End Time It is the end time of people counting report.
4.4.8 Heat Map It can generate report according to the density statistics of object movement. The color ranges from blue to red, blue means the minimum of heat value while red means the maximum of heat value. The original data will be removed when mirror or view angle changes. 4.4.8.1 Set Rule Precondition It has set the heat map smart plan of tracking speed dome, please refer to "4.4.4 Smart Plan" for more details.
Step 3 Select "Enable" to enable heat map function. Step 4 Configure working period. 1. Click "Setup" and the system will pop out the interface of "Working Period", which is shown in Figure 4-78. Figure 4-78 2. Set alarm period. Method 1: Press the left mouse button and drag on the setting interface directly to make setting. Method 2: Click the "Setup" of the corresponding day, select the check box in front of the period at the bottom and input time value, there are six periods to be set every day.
Precondition It has enabled heat map function, please refer to "4.4.8.1 Set Rule" for more details. Operation Steps Step 1 Select "Setup > Event > Heat Map > Report" and the system will display the interface of "Report", which is shown in Figure 4-79. Figure 4-79 Step 2 Set start time and end time. Step 3 Select the serial number of people counting which needs to be inquired. Step 4 Click "Search" and the system will display the result of heat map. 4.4.
Figure 4-80 Step 2 Select "Enable" to enable alarm linkage. Step 3 It is to set the parameters of alarm, please refer to Table 4-41 for more details. Parameter Function Relay-in It is to select external alarm device. Working Period It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
Parameter Function Anti-dither System only records one alarm event during the anti-dither period. Sensor Type It is to select NO or NC according to the type of external alarm device sensor. Select check box and set record channel, the corresponding channel will implement alarm and record automatically when alarm happens. Note Please refer to "4.1.2.5 Set Path" for record file storage location query and setting. The system record needs to meet following two conditions when alarm happens.
4.4.10 Abnormity Abnormity includes SD card abnormity, network abnormity and illegal access. Note Only the device with SD card function has these three statuses: No SD card, Capacity warning, and SD card error. 4.4.10.1 SD Card Abnormity The system can generate alarm and activate the actions which have been set when SD card is abnormal. SD card abnormity includes No SD card, capacity warning and SD card error.
Parameter Function Relay-out Connect alarm output port to alarm device (such as lamplight, siren and so on), select check box and set alarm output device, enable alarm linkage output port, and the system can activate corresponding alarm output device when alarm occurs. Alarm Delay System can delay the alarm output for specified time after alarm ended. Send Email Select check box, and the system will send email to inform users when Alarm occurs.
Step 2 Set event type. Step 3 Select "Enable" to enable the function of network abnormity detection. Step 4 It is to set the parameters of network abnormity, please refer to Table 4-43 for more details. Parameter Function Record Select check box and set record channel, the corresponding channel will implement alarm and record automatically when alarm happens. Note Please refer to "4.1.2.5 Set Path" for record file storage location query and setting.
Figure 4-83 Step 2 Select "Enable" to enable the function of illegal access function. Step 3 It is to set the parameters of illegal access detection, please refer to Table 4-44 for more details. Parameter Function Login Error It is the times of continuously inputting wrong password when logging in the device. When the times of login error exceeds the set value, the account will be locked.
Click "Save" to complete setting 4.5 Storage 4.5.1 Set Schedule Config schedule includes configuring record, snapshot and holiday. Note The device will fail to record or snapshot according to the schedule if the record mode is off in the record control. 4.5.1.1 Set Record Schedule It is to set the record schedule of panorama camera or tracking speed dome, record type includes general, motion and alarm.
Step 2 When the "Channel" is set as "1", it is to set the record schedule of tracking speed dome. When the "Channel" is set as "2", it is to set the record schedule of panorama camera. Step 3 Select record type and set period. Note You can select record type by pressing the left button and dragging on the time line of the corresponding day on the interface of record schedule, and then you can set the period of different record types. 1.
it is to set snapshot schedule of panorama camera or tracking speed dome, snapshot type includes general, motion and alarm. Step 1 Select "Setup > Storage > Schedule > Snapshot Schedule" and the system will display the interface of "Snapshot Schedule", which is shown in Figure 4-86. Figure 4-86 Step 2 When the "Channel" is set as "1", it is to set the snapshot schedule of tracking speed dome. When the "Channel" is set as "2", it is to set the snapshot schedule of panorama camera.
Figure 4-87 2. Select day and the check box in front of the period, and set period. Note There are six periods which can be set every day. The setting will be applied to the whole week if it selects all, you can also select the check box in front of the day to make separate setting upon several days. 3. Select the snapshot type of corresponding period. 4. Click "Save" and the system will return to the interface of "Snapshot Schedule". Different colors means different types of snapshot schedule.
Figure 4-88 Step 2 Select "Record" or "Snapshot". Step 3 Click the date which needs to be set as holiday. The selected date will display yellow shading. Step 4 Click "Save" to complete setting. 4.5.2 Destination 4.5.2.1 Set Path Path can help to configure the storage mode of record and snapshot according to the event type, you can select local SD card, FTP or NAS for storage. Check it to store corresponding type of record or snapshot to the needed storage device.
Only the device which supports SD card can display "Local". Step 1 Select "Setup > Storage > Destination > Path" and the system will display the interface of "Path", which is shown in Figure 4-89. Figure 4-89 Step 2 Select storage mode for the corresponding type the event of record or snapshot according to the actual situation. Parameter Note Event Type It includes scheduled, motion detection and alarm. Local Store it to SD card. FTP Store it on the FTP server. NAS Store it on the NAS server.
Figure 4-90 4.5.2.3 Set FTP FTP function can be enabled when destination selects FTP storage mode. When network disconnection or malfunction occurs, it can emergently store all record or snapshot to the local SD card. Step 1 Select "Setup > Storage > Destination > FTP" and the system will display the interface of "FTP", which is shown in Figure 4-91. Figure 4-91 Parameter Server Address Port User Name Password Note FTP server address FTP server port.
Parameter Remote Directory Emergency (Local) Note It is the password which is used to log in FTP server. Store it to the directory on the FTP server. Select the check box, record or snapshot will be stored to local SD card when FTP is abnormal. Table 4-46 Step 4 Click "Save" to complete setting. 4.5.2.4 Set NAS Server NAS function can be enabled when the path selects NAS storage mode. Select NAS storage to store the files into the NAS server.
Step 4 Click "Save" to complete setting. 4.5.3 Record Control It is to configure pack duration, pre-event record, disk full, record mode and record stream. Step 1 Select "Setup > Storage > Record Control" and the system will display the interface of "Record Control", which is shown in Figure 4-93. Figure 4-93 Step 2 It is to configure the parameters of record control, please refer to Table 4-48 for more details. Parameter Note Pack Duration It is the duration to pack each video file.
Parameter Record Mode Record Stream Note The system will begin to record when selecting manual mode; the system will begin to record within the period of record schedule set by the system. It includes main stream and sub stream. Table 4-48 Step 3 Click "Save" to complete setting. 4.6 System 4.6.1 General It includes general, date&time and splicing. 4.6.1.1 General It is to set the device name, language and video standard.
Parameter Video Standard Note It is to display the video standard of the device, such as 50Hz. Table 4-49 Step 3 Click "Save" to complete setting. 4.6.1.2 Date & Time It is to set date format, time format, time zone, system time, enable DST or set NTP server. Step 1 Select "Setup > System > General > Date&Time" and the system will displayt the interface of 'Date&Time", which is shown in Figure 4-95.
Parameter Date Format Time Format Time Zone Current Time DST Enable Synchronize with NTP NTP Server Port Update Period Note It is the date format displayed by the system. It is the time format displayed by the system, including 24-hour system and 12-hour system. It is the time zone where the device is located. It the current system time of the device. Click "Sync PC" and it will adjust system time on the basis of PC time. It needs to enable DST when the place where the device is located implements DST.
Step 3 Click "Start" and the system will begin to splice the panorama camera which has been selected. 4.6.2 Account Users can implement user management operation only when they have user management authority. The user name or group supports max 31 characters, which only consists of letter, number, underline, spot or @. The password can be set between 8 and 32 characters, which can only be number and letter.
Figure 4-97 Step 2 Click "Add Group" and the system will pop out the dialog box of "Add Group", which is shown in Figure 4-98. Figure 4-98 Step 3 Fill in the group name and remark information, select authority list of the group.
Step 4 Click "Save" to complete adding. It will display newly-added group in the group list, which is shown in Figure 4-97. Note Click after adding group, you can modify the remark and authority of the group; click to delete the added group, admin and user group can't be deleted. Click the corresponding of admin or user group, and it can only modify the remark of group. Figure 4-99 4.6.2.2 Add User There is admin user by default for the system, you can add user.
Figure 4-100 Step 2 Click "Add User" and the system will pop out the dialog box of "Add User", which is shown in Figure 4-101.
Figure 4-101 Step 3 It is to configure the parameters of user, please refer to Table 4-51 for more details. Parameter Note User name It is the unique name which is used to identify user. It can't be repeated. Password It is the password and confirm password of user. Confirm "Confirm Password" has to be the same as "Password". Password It is the group to which the users belong. Different groups have different Group authorities. Remark The description info of users.
Step 4 Click "Save" to complete adding. The newly-added user will be displayed in the user list, which is shown in Figure 4-102. Note Click after adding user, you can modify user password, group to which the user belongs, remark and authority; click Click the corresponding to delete the added user, admin user can't be deleted. of admin user and it can modify the password of admin user. Figure 4-102 4.6.3 Add Onvif User There is admin user by default for the system, you can add user.
Figure 4-103 Step 2 Click "Add User" and the system will pop out the dialog box of "Add User", which is shwon in Figure 4-104. Figure 4-104 Step 3 Input user name, password and confirm password, and select group. Group includes admin, operator and user for you to select according to the actual situation. Step 4 Click "Save" to complete adding.
Note Click after adding user, you can modify user password, group to which the user belongs, remark and authority; click Click the corresponding to delete the added user, admin user can't be deleted. of admin user and it can modify the password of admin user.
5 System Maintenance 5.1 Maintenance Requirements It is recommended to implement system management, backup and maintenance according to the following operations in order to make sure the system is normal and it operates safely. Check monitoring image of the device regularly. Remove unused user and group regularly. Modify user password every three months. Check system log and analyze regularly, deal with abnormities in time. Back up system config regularly. Restart and delete old files regularly.
5.2.2 Delete Old Files Delete the video or pictures stored in SD card, FTP or NAS server according to the time which has been set. Step 1 Select "Setup > System > Auto Maintain" and the system will display the interface of "Auto Maintain", which is shown in Figure 5-2. Figure 5-2 Step 2 Select "Auto Delete Old Files" and customize the period when it needs to delete files. The time range is between 1 day to 31 days. Step 3 Click "Save" to complete setting. 5.3 Backup and Recovery 5.3.
Figure 5-3 Step 2 Click "Import/Export" and select backup path. The "Backup Path" will display export path after export is configured. 5.3.2 Recover Device Config Info It can import config file and quickly configure device info or recover device config info via configuring import and export function. Step 1 Select "Setup > System > Import/Export" and the system will display the interface of "Import/Export", which is shown in Figure 5-4. Figure 5-4 Step 2 Click "Export" to select config file.
5.3.3 Default Caution All the device configs will be restored to default except network IP address and user management, please operate carefully. Select "Setup > System > Default" and the system will display the interface of "Default", which is shown in Figure 5-5. Click "Default" to restore the device to default. Figure 5-5 5.4 Upgrade It is to upgrade the device firmware.
The upgrade file is a type of *.bin file. Step 3 Click "Upgrade" and the system will begin to upgrade firmware. 5.5 Version It is to check system harware characteristics, software version and WEB version etc. Note Different devices may have different version info, please refer to the actual interface for more details. Select "Setup > System > Version" and the system will display the interface of "Version", which is shown in Figure 5-7. Figure 5-7 5.
Figure 5-8 Step 2 Set "Start Time" and "End Time", and select log type. The earliest start time is Jan 1st 2000, and the latest end time is Dec 31st 2017. Log type includes system operation, config operation, data operation, event operation, record operation, user management and clear log. System operation: it includes program start, abnormal exit, exit, application restart, close/restart device, system reboot, system upgrade. Config operation: It includes save config, delete config file.
Click "backup" to back up the seached log info to local PC. Click "Clear" to clear all the log info on the device, please operate carefully. Figure 5-9 5.7 Online User It is to check info of the users who has currently logged in the WEB. Select "Setup > System > Online User" and the system will display the interface of "Online User", which is shown in Figure 5-10.
Note: This manual is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. All trademarks and registered trademarks mentioned are the properties of their respective owners. If there is any uncertainty or controversy, please refer to the final explanation of us. Please visit our website for more information. ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. Address: No.
