Dahua Network Camera Web 3.0 Operation Manual Dahua Network Camera Web3.0 Operation Manual Version 1.0.1 Dahua Vision Technology CO.
Dahua Network Camera Web 3.0 Operation Manual Table of Contents 1 2 3 4 5 Network Config ............................................................................................................................ 1 1.1 Network Connection ..................................................................................................... 1 1.2 Log in .............................................................................................................................. 1 Live ..................
5.2 5.3 5.4 5.5 Dahua Network Camera Web 3.0 Operation Manual 5.1.1 Conditions ............................................................................................................... 30 5.1.2 Video ...................................................................................................................... 42 5.1.3 Audio ...................................................................................................................... 54 Network.......................................
6 7 Dahua Network Camera Web 3.0 Operation Manual 5.5.6 Remote control ........................................................................................................ 132 5.5.6 Auto Maintenance................................................................................................. 133 5.5.7 Upgrade ................................................................................................................ 134 5.6 Information ............................................................
Dahua Network Camera Web 3.0 Operation Manual Important The following functions are for reference only. Some series products may not support all the functions listed below.
Dahua Network Camera Web 3.0 Operation Manual 1 Network Config 1.1 Network Connection Network camera and PC connection mainly has two ways, see Figure 1- 1 and Figure 1-2. Figure 1- 1 Figure 1-2 Before you access network camera via the Internet, you need to have its IP address. User can use Config Tool to search IP of the network camera. Please refer to Config Tool manual. 1.
Dahua Network Camera Web 3.0 Operation Manual After successful connection, the login interface is shown as in Figure 1-3; input your user name and password. Default factory username is admin and password is admin. Figure 1-3 The system will display “Update Password” prompt box for your first login, users need to modify the password and save it properly. Figure 1-4 After successful login, you may see the interface shown as in Figure 1-5.
Dahua Network Camera Web 3.0 Operation Manual Figure 1-5 Click on “Please click here to download and install the plug-in”. The system pops up warning information to ask you whether run or save this plug-in. See Figure 1-6.
Dahua Network Camera Web 3.0 Operation Manual Figure 1-6 You must either run or save the file to local and install it. Follow the following steps. Click on run, you will see Figure 1-7and Figure 1-8.
Dahua Network Camera Web 3.0 Operation Manual Figure 1-8 When plug-in installation completes, the installation page closes automatically. The web-end will refresh automatically, and then you can view video captured by the camera.
Dahua Network Camera Web 3.0 Operation Manual 2 Live After you logged in, you can see the live monitor window. See Figure 2-1. 2 1 3 4 Figure 2-1 There are four sections: Section 1: Encode setup bar Section 2: System menu Section 3: Window function option bar Section 4: Window adjust bar 2.1 Encode Setup Note: Some series don’t support sub stream 2. The encode setup interface is shown as in Figure 2-2. Figure 2-2 Please refer to the following sheet for detailed information.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Main stream Click it to enable main stream video monitoring and click again to disable it. Generally for storage and monitor. Click it to enable Sub Stream1 video monitoring and click again to disable it. When network bandwidth is insufficient, it substitutes main stream for monitoring. Click it to enable Sub Stream 2 video monitoring and click again to disable it.
Dahua Network Camera Web 3.0 Operation Manual When the video is in the original status, click it you can select any zone to zoom in. In the non-original status, you can drag the zoom-in zone in specified range. Right click mouse to restore previous status. Click it; you can use the middle button of the mouse to zoom in/out the video size. Click on the button to snapshot, save picture to path in Ch 5.1.2.5.
Dahua Network Camera Web 3.0 Operation Manual Figure 2-6 Click this button to display/hide image control interface. Click it to open picture setup interface. This interface is on the top right pane. Please refer to the following sheet for detailed information. Parameter Function Video setup It is to adjust monitor video brightness. It is to adjust monitor video contrastness. It is to adjust monitor video hue. Note: All the operations here apply to WEB end only.
Dahua Network Camera Web 3.0 Operation Manual 2.4.4 Width and Height Ratio Click it to restore original ratio or suitable window. 2.4.5 Fluency Adjustment There are three levels of fluency for you to select (Realtime, Normal, and Fluency). The default is normal. 2.4.6 Rules Info Click the button, preview image will display intelligent rules after enabling; it is “enable” by default. 2.4.
Dahua Network Camera Web 3.0 Operation Manual Parameter Zoom Focus Function Adjust the focal length of the lens by clicking or long pressing “+”“-”buttons. Step length is used to adjust the length of one step with one click. Adjust the sharpness of the lens by clicking or long pressing“+”、“-” buttons. Step length is used to adjust the length of one step with one click. Click to adjust the image definition automatically.
Dahua Network Camera Web 3.0 Operation Manual Figure 2-8 parameter Note Installation Mode Three modes which are ceiling mount, wall mount and ground mount. It represents the display mode of the current image (default supports original image mode), the display modes may be different according to different installation modes.
Dahua Network Camera Web 3.0 Operation Manual parameter Note 360°expanded rectangular panorama +6 independent sub image, both the sub image and the subbox in the expanded rectangular panorama support zoom and movement, for the expanded rectangular panorama also supports left and right starting point movement. Original image + 8 independent sub images, both the sub image and the subbox in the original image support zoom and movement.
Dahua Network Camera Web 3.0 Operation Manual 1P: Original picture 1P+3: Original picture and three trigger track windows, it can adjust the location and size of three trigger track windows on the original picture. 1P+5: Original picture and five trigger track windows, it can adjust the location and size of five trigger track windows on the original picture.
Dahua Network Camera Web 3.0 Operation Manual 3 PTZ Control Here you can view direction keys, speed, zoom, focus, iris, preset, tour, scan, pattern, aux on, off and PTZ setup button. See Figure 3-1. Note: Before PTZ operation, please make sure you have properly set PTZ protocol. (Please refer to Ch 5.5.3). Currently only IPC-HFXXXX series and –PT series products can support PTZ function.
Dahua Network Camera Web 3.0 Operation Manual Figure 3-2 PTZ setting interface is shown as in Figure 3-3. Here you can set scan, preset, tour, pattern, assistant function and light and wiper plus view coordinate. Figure 3-3 3.1 Scan Scan interface is shown in Figure 3-4.
Dahua Network Camera Web 3.0 Operation Manual Figure 3-4 Steps to scan are: Step 1. Click on Set button, display icon. Step 2. Move via direction key to select left, click on Set Left to set left border of camera Step 3. Move via direction key to select right, click on Set Right to set right border of camera. Step 4. Complete scan path setup. 3.2 Preset Preset interface is shown in Figure 3-5. Figure 3-5 Steps to preset are: Step 1. In preset box, input preset value. Step 2.
Dahua Network Camera Web 3.0 Operation Manual Figure 3-6 Steps to tour are: Step 1. In tour box, input tour path value. Step 2. Click on Add. Range of tour relates to PTZ protocol. Step 3. In preset box, input preset value. Step 4. Click on Add as to add a preset in this tour. If click on Del, it deletes this preset in tour. Note: You can add more than one preset here, or delete more than one preset. 3.4 Pattern Pattern interface is shown in Figure 3-7.
Dahua Network Camera Web 3.0 Operation Manual Click “Start” and it will start pattern according to the pattern spot which has been set; click “Stop” and the pattern ends. 3.5 Assistant Assistant interface is shown in Figure 3-8. Figure 3-8 Steps to assistant are: Step 1. In assistant box input assistant value. Step 2. Click on Aux On to turn on aux function. Click on Aux off to turn off aux function. 3.6 Light Wiper Light wiper interface is shown in Figure 3-9.
Dahua Network Camera Web 3.0 Operation Manual 4 Playback Web client playback supports video playback and picture playback. Note: Before playback, user shall set storage management as in Ch. 5.4. 4.1 Playback The playback interface is shown as in Figure 4-1.
Dahua Network Camera Web 3.0 Operation Manual 4.1.1 Function of Play The function of play is shown as in Figure 4-2 and Figure 4-3. Figure 4-2 Figure 4-3 Parameter Function ① Play When you see this button, it means pause or not played record. Click on this button, switch to normal play status. ② Stop Click this button to stop playing. Click on this button to go to next frame. ③ Play by frame Note: You shall pause record when you use this function. ④ Slow Click on this button to play slowly.
Dahua Network Camera Web 3.0 Operation Manual 4.1.2 Playback File In calendar, blue date represents data currently has video record or snapshot. See Figure 4-4. Figure 4-4 Parameter File Type Data Source Function Select “dav”, as video playback. Select “jpg” as picture playback. Default is SD card. Step 1. Click on data in blue, time axis displays record file progress bar in color.
Dahua Network Camera Web 3.0 Operation Manual Figure 4-6 Parameter Search Download Format Function It means records within searched start time and end time on the date. There are two formats: dav, mp4.
Dahua Network Camera Web 3.0 Operation Manual Parameter Download Back Function click the download button and download file to path in Ch. 5.1.2.5. System does not support download and playback at the same time. Click on back button to go to calendar interface. 4.1.3 Playback Cut Note: Playback cut function will automatically pause playing record as playback cut and playback cannot be at the same time. Step 1. Click on start time to cut on time axis. This time must be within progress bar range.
Dahua Network Camera Web 3.0 Operation Manual Figure 4-9 Parameter Function 24 hours Click on it, means video in past 24 hours. 2 hours Click on it, means video in past 2 hours. 1 hour Click on it, means video in past 1 hour. 30 min Click on it, means video in past 30 min. 4.1.6 Assistant Function Video playback assistant function is shown in Figure 4-10.
Dahua Network Camera Web 3.0 Operation Manual See Figure 4-11. Figure 4-11 4.2.1 Play Figure 4-12 Default icon is and it means pause or not played picture. Click on play button to switch to normal play status. Icon become Click on it to pause. 4.2.
Dahua Network Camera Web 3.0 Operation Manual Figure 4-13 Step 1. Click on file list , select snapshot file of the date. Step 2. Double click on file in list, to play this snapshot. Parameter Search Function It means all snapshot files within the start time and end time of selected date.
Dahua Network Camera Web 3.0 Operation Manual Parameter Download Back Function Click the download button to open snapshot file or directly download to local according to the browser types. Click the back button to return to calendar interface and re-select time. Figure 4-14 4.2.
Dahua Network Camera Web 3.0 Operation Manual After checking snapshot file type, in file list only display file of selected type. Users can also select the snapshot type to be displayed via the dropdown box above the file list. See Figure 4-15.
Dahua Network Camera Web 3.0 Operation Manual 5 Setup Web client setup support camera, network, time, storage, system and system info view. 5.1 Camera The camera setting includes conditions, profile management, zoom and focus. 5.1.1 Conditions Note: The camera parameter may be different according to different models, please refer to the actual product for more details. 5.1.1.1 Picture Note: The device which supports true WDR fails to support long exposure when true WDR is enabled.
Dahua Network Camera Web 3.0 Operation Manual Parameter Note It is to adjust the image overall brightness via linear adjustment mode. Brightness The larger the number is, the brighter the picture is, and on the contrary it is opposite. The picture get blurry easily when the value is set too big. Contrast It is to adjust the picture contrast. The bigger the value is, the bigger the bright contrast becomes, and on the contrary it is smaller.
Dahua Network Camera Web 3.0 Operation Manual 5.1.1.2 Exposure Step 1 Select “Setup > Camera > Conditions > Exposure”. The system will display the “Exposure” interface which is shown in Figure 5-2. Figure 5-2 Step 2 It is to set the exposure parameter, please refer to the following sheet for more details. Parameter Note You can switch to exposure mode when it is in outdoor mode, it can realize the result in the corresponding exposure mode.
Dahua Network Camera Web 3.0 Operation Manual Parameter Note It is the camera exposure mode. Note: When “Anti-flicker” is “Outdor”, the “exposure mode” can be set as “gain priority” or “shutter priority” mode. Different devices have different exposure modes; please refer to the actual interface. It includes the following options: Auto: It can auto adjust the image brightness according to the environment.
Dahua Network Camera Web 3.0 Operation Manual Step 3 Click “Save” to complete the parameter config of camera exposure. 5.1.1.3 Backlight Backlight mode can be divided into BLC, WDR and HLS. BLC: it can avoid cucoloris phenomenon of the darker area in the backlight environment. WDR: It can suppress the overbright area and compensate darker area by enabling WDR, which can make the overall image clear.
Dahua Network Camera Web 3.0 Operation Manual When selecting “Customized” mode, the system can realize exposure upon the selected area after it set customized area, which is to make the image of the selected area reach appropriate brightness. When the “Mode” is set as “WDR”, it will lower the brightness of the area with high brightness and enhance the brightness of the area with low brightness, which is to make the objects in both high brightness and low brightness area display clearly.
Dahua Network Camera Web 3.0 Operation Manual When the “Mode” is set as “Auto”, the system can auto compensate white balance upon different color temperatures, which is to make the image color normal. When the “Mode” is set as “Natural”, the system can auto compensate white balance to the scene without artificial light, which is to make the image color normal.
Dahua Network Camera Web 3.0 Operation Manual Step 2 Set day & night parameter; please refer to the following sheet for more details. Parameter Mode Sensitivity Delay Note It is to set the camera image displayed as color or black & white mode. Note: The setting of “Day/Night Mode” is not affected by the setting of “Profile Management”. It includes the following options: Color: The camera image is displayed as color image.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-6 Step 2 It is to set defog mode according to the actual scene. When the “Mode” is set as “Manual”, it is to manually set intensity and air light mode, the system will adjust the image definition according to the intensity and air light mode which have been set previously. As for air light mode, you can set manual or auto. When the “Mode” is set as “Auto”, the system will auto adjust the image definition according to the actual scene.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-7 Step 2 It is to set IR light mode according to the actual scene. When the “Mode” is set as “Manual”, it can manually set the brightness of IR light; the system will realize light compensation to the image according to the IR light intensity. When the “Mode” is set as “Smart IR”, the system can adjust the light brightness according to the actual scene.
Dahua Network Camera Web 3.0 Operation Manual 5.1.1.8 Profile Management Step 1 Select “Setup > Camera > Conditions > Profile Management” and the system will display the interface of “Profile Management”. Step 2 Set profile management. When the “Profile Management” is set as “Normal”, the system will monitor according to the normal config.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-10 Step 3 Click “Save” to complete the settings of profile management. Note: Click “Default” to restore the device to default config; click “Refresh” to check the latest config file of the device. 5.1.1.9 Zoom and Focus Note: Only motorized vari-focal devices support focus and zoom function. Step 1 Select “Setup > Camera > Conditions > Zoom and Focus” and the system will display the interface of “Zoom and Focus” which is shown in Figure 5-11.
Dahua Network Camera Web 3.0 Operation Manual Step 2 Adjust the focal length of the lens. After it is zoomed, set “Speed” and press “+”, “-“or drag the sliding block directly to adjust. Step 3 Adjust the lens definition. After it is focused, set “Speed” and press “+”, “-“or drag the sliding block directly to adjust. Note: Speed is used to set the length by pressing “+” and “-“.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-13 (Fisheye) Step 2 Set video bit stream, please refer to the following sheet for more details about the parameters. Parameter Installation Mode Function It will display the parameter when the device is fisheye. There are three installation modes for fisheye which are ceiling, wall mount and ground installation, please select installation mode according to the actual installation scene of the fisheye.
Dahua Network Camera Web 3.0 Operation Manual Parameter Record Mode Sub Stream Enable Smart Codec Function It will display the parameter when the device is fisheye. The system will begin to switch after record mode is switched, it will prompt saved successfully after it is switched successfully. The record mode will change according to the different installation modes. 1O: the original picture which is not dewarped. 1P: 360°rectangular panorama.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Encode mode There are five options: H.264 (main profile standard, H.264H (high profile standard), H.264B (Baseline Profile), H.265 (main profile standard) and MJPEG encode. The H.264, H.264H both are H264 bit stream. H.264 is the Main Profile encode and you need to enable the sub stream function in your camera and set the resolution as CIF. Then you can monitor via the Blackberry cell phone. The H.265 is the main profile encode mode.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Watermark Settings Select “Watermark Setting” and enable watermark function. After the watermark function is enabled, you can check if the video is tampered via verifying watermark character. Watermark Character It is the character of watermark verification, it is DigitalCCTV by default. Video Clip 1. Select “Sub Stream 2” in the drop-down box, click “Enable”. 2. Enable “Video Clip”, click .
Dahua Network Camera Web 3.0 Operation Manual 3. Select the needed resolution and clip the needed image on the interface, which is shown in Figure 5-15. 4. Click “Save”. You can check the clipped video in the preview interface (the sub stream 2 preview interface only displays the clipped area), which is shown in Figure 5-15. Figure 5-15 Step 3 Click “Save” to complete video stream setup. 5.1.2.2 Snapshot The snapshot interface is shown as in Figure 5-16.
Dahua Network Camera Web 3.0 Operation Manual Please refer to the following sheet for detailed information. Parameter Function Snapshot type There are two modes: general (schedule) and Event (activation). Image size It is the same as the resolution of main stream. Quality It is to set the image quality. There are six levels. Interval It is to set snapshot frequency. Optional1~7s/picture, customized. 5.1.2.3 Video Overlay The video overlay interface is shown as in Figure 5-17.
Dahua Network Camera Web 3.
Dahua Network Camera Web 3.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-22 Please refer to the following sheet for detailed information. Parameter Function Privacy Masking Time Title Channel Title Text Overlay Picture Overlay Here you can privacy mask the specified video in the monitor video. System max supports 4 privacy mask zones. You can enable this function so that system overlays time information in video window. You can use the mouse to drag the time tile position.
Dahua Network Camera Web 3.0 Operation Manual Check “Enable” to display the counting statistics data in Counting Refresh Default the video monitoring window; check “Disable” not to display. There are enter number and leave number for statistics type and left align and right align for OSD info. Set privacy mask, channel title, time title, location, overlay and save the change. You can click on Refresh to see effect. Click it to restore default config. Save Click it to complete video settings.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-24 Parameters Enable Note Check “Enable”, then it will display the ROI in the video monitoring window; Check “Disable”, then it won’t display. Set the image quality of ROI, ranging from 1～6, default is 6. Note: Image Quality For fisheye device, it ranges from 1~6 (best), default is 6 (best) Able to set area block, max 4 areas. 5.1.2.5 Path The storage path interface is shown as in Figure 5-25.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-25 5.1.3 Audio Please note some series devices do not support audio function. 5.1.3.1 Audio The audio interface is shown as below. See Figure 5-26. Figure 5-26 Please refer to the following sheet for detailed information.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Enable You can enable audio only when video is enabled. After selecting the “Enable” of main stream or sub stream, the network transmission stream is the audio/video composite stream, otherwise it only includes video image. Encode mode The encode mode of the main stream and extra stream include G.711A, G.711Mu, G.726 and ACC. The default mode is G.711A. The setup here is for audio encode mode and the bidirectional talk encode both.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-27 Figure 5-28 Audio management currently supports PCM format to record and PCM, wav two forms to upload， and can select an audio file for the audio alarm linkage. The way to download the web alarm playback audio file into local is as follows: Step 1 Use the left mouse button to click the hollow circle and shows in the “choice” column on the left, ，which means effective choice of alarm audio.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-29 Please refer to the following sheet for detailed information. Parameter Function Host Name It is to set current host device name. It max supports 15 characters. Ethernet Card Please select the Ethernet port. Default is wired. Please note you can modify the default Ethernet card if there is more than one card. Mode There are two modes: static mode and the DHCP mode.
Dahua Network Camera Web 3.0 Operation Manual Enable ARP/Ping set device IP address service. You can use ARP/Ping command to modify or set the device IP address if you know the device MAC address. Before the operation, please make sure the network camera and the PC in the same LAN. This function is on by default. You can refer to the steps listed below. Step 1: Get an IP address. Set the network camera and the PC in the same LAN. Step 2: Get the physical address from the label of the network camera.
Dahua Network Camera Web 3.0 Operation Manual 5.2.2 Connection 5.2.2.1 Connection The connection interface is shown as in Figure 5-31. Figure 5-31 Please refer to the following sheet for detailed information. Parameter Function Max connection It is the max Web connection for the same device. The value ranges from 1 to 20. Default connection amount is 10. TCP port Port range is 1025~65534. The default value is 37777. You can input the actual port number if necessary.
Dahua Network Camera Web 3.0 Operation Manual RTSP port The default value is 554. Please leave blank if use default. User uses QuickTime or VLC can play the following formats. BlackBerry can play too. Real-time monitoring URL format, please require real-time RTSP media server, require channel no., bit stream type in URL. You may need username and password. User uses BlackBerry need to set encode mode to H.264B, resolution to CIF and turn off audio.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-32 5.2.3 PPPoE The PPPoE interface is shown as in Figure 5-33. Enter the PPPoE username and password which are provided by ISP (Internet Service Provider), and click “Enable”. The network camera will automatically establish network connection in the mode of PPPoE after it is enabled, after it is successful, the IP of the “IP Address” will be automatically modified into the dynamic IP address of the acquired WAN.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-33 5.2.4 DDNS The DDNS interface is shown as in Figure 5-34. The DDNS is to set to connect the various servers so that you can access the system via the server. Please go to the corresponding service website to apply a domain name and then access the system via the domain. It works even your IP address has changed. When the device connects to WLAN, you should disable UPnP. Figure 5-34 Please refer to the following sheet for detailed information.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Server Type You can select DDNS protocol from the dropdown list: CN99 DDNS, NO-IP DDNS, Dyndns DDNS, Dahua DDNS, the default is Dahua DDNS. Server Address DDNS server IP address CN99 DDNS Server address: www.3322.org NO-IP DDNS Server address: dynupdate.no-ip.com Dyndns DDNS Server address: members.dyndns.org Dahua DDNS Server address：www.dahuaddns.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Server Type You can select CN99 DDNS protocol Server Address Under CN99 DDNS the default server address is “www.3322.org” Domain Name Self-defined domain name Username The user name you input to log in the server. Password The password you input to log in the server Refresh Period The refresh period of the connection between the device IP and the server, default is 10 minutes. 5.2.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-37 Please refer to the following sheet for detailed information. Parameter Function SMTP Server Input server address and then enable this function. Port Default value is 25. You can modify it if necessary. Anonymity For the server which supports the anonymity email function, it won’t display the information of the sender. User Name The user name of the sender email account. Password The password of sender email account.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Interval The send interval ranges from 0 to 3600 seconds. 0 means there is no interval. Please note system will not send out the email immediately when the alarm occurs. When the alarm, motion detection or the abnormity event activates the email, system sends out the email according to the interval you specified here.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-38 5.2.8 SNMP The SNMP interface is shown as in Figure 5-39 and Figure 5-40. The SNMP allows the communication between the network management work station software and the proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or establish the SNMP service before you use this function. You need to reboot the device to activate the new setup. Figure 5-39 Please refer to the following sheet for detailed information.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function SNMP Version Check SNMP v1, device only process v1 info. Check SNMP v2, device only process v2 info. Check SNMP v3, can set username, password and encryption method. Server calibrate corresponding username, password and encryption method too access device and v1/v2 are unavailable. SNMP port The listening port of the proxy program of the device. It is a UDP port not a TCP port. The value ranges from 1 to 65535.
Dahua Network Camera Web 3.0 Operation Manual Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, users need to configure parameter in chart. Parameter Function SNMP Version SNMP v3 Read-only Username Read/Write Username Default is public. Note: Name only can be number, letter and underline. Default is private. Note: Name only can be number, letter and underline.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-41 5.2.10 Multicast The multicast interface is shown as in Figure 5-42. Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host can just send out one data to transit. This function also depends on the relationship of the group member and group of the outer.
Dahua Network Camera Web 3.0 Operation Manual Note: This function is only for series with 4G module. 4G is a mobile communication system which makes wireless communication integrates with Internet and multimedia communication. 5.2.11.1 Dialing Setting Figure 5-43 Parameter Function Wireless Net Type Auto, WCDMA, FDD-LTE optional, you can select according to the operator. Enable Check to enable 4G module. APN It shall be acquired from the operator according to the setup of operator.
Dahua Network Camera Web 3.0 Operation Manual Time Range It is the time period to set dial-up. It can activate the function via message to enable/disable dial-up function if it is beyond the time period. IP Address It will display the acquired IP after the dial-up is successful via 4G. 5.2.11.2 Mobile Setting Figure 5-44 Please refer to the following sheet for detailed information.
Dahua Network Camera Web 3.0 Operation Manual Note: Some series devices don’t support WIFI and WPS function. WPS function is supported by the devices with WPS button. 5.2.12.1 WIFI WIFI info can show the name, status, IP information of the Current Hot Spot. Usually please “Refresh” WIFI work information after reconnection to ensure the real-time display of the work status, because it often takes some time to connect WIFI Hot Spot, which depends on the network signal strength.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-46 Step 3 Click “Add SSID” when need to add a wireless network manually pop out an interface in the figure below, and enter network ID in the dialog box. Figure 5-47 Step 4 Double click on one can pop out the signal intensity and authentication of the hot spot. · Please enter the password if necessary. Please keep the choice of password index number same as the router when entering password.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-48 PIN Number and SSID are both acquired from the router, please “refresh” the work information of WIFI to ensure the real-time display of work state after filling in correctly. 5.2.13 802.1x 802.1x (port based network access control protocol) supports manual selection of authentication method to control if device connected to LAN can join the LAN. It well supports authentication, charging, safety and management requirement of network.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Authentication PEAP (protected EAP protocol). Username It needs the username to login, which is authenticated by the server. Password Please input password here. 5.2.14 QoS The QoS interface is shown as below. See Figure 5-50. Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and jam problem and etc.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Command The value ranges from 0 to 63. The router or the switcher can provide different service for various data packets. Enable Wireless QoS Check it to enable QoS. 5.2.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-52 3. Fill in corresponding “Country”, “Province” and some other information, click “Create” after filling in. It will show the prompt of “Create Successfully”, which means the server certificate has been successfully created. Note: Make sure the “IP or domain name” is the same as that of the device. 4. Click “Install” and it will install the certificate on the device end, which is shown in Figure 5-53.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-53 5. Click “Download”. It will pop out the dialog box of “Save as”, save the file into the computer.
Dahua Network Camera Web 3.0 Operation Manual 6. Double click the downloaded icon of “RootCert.cer”. The system will display the information interface of “Certificate”, which is shown in Figure 5-55. Figure 5-55 7. Click “Install Certificate” and it will pop out the interface of “Certificate Import Wizard”, which is shown in Figure 5-56.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-56 8. Click “Next”. Select “Trusted Root Certification Authorities”, which is shown in Figure 5-57.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-57 9. Click “Next”. The system will display the interface of “Completing the Certificate Import Wizard”, which is shown in Figure 5-58.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-58 10. Click “Finish”, and it will pop out the dialog box of “Security Warning”, which is shown in Figure 5-59.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-59 11. Click “Yes”. It will pop out the dialog box of “Import Successful”, click “Ok” to complete downloading certificate, which is shown in Figure 5-60. Figure 5-60 Please refer to the following steps if you select “Install Signed Certificate”. 1. Select “Setup > Network > HTTPs”. The system will display the interface of HTTPs, which is shown in Figure 5-61.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-61 2. Select signed certificate and certificate key path respectively via “Browse”, click “Upload”. 3. Install root certificate, please refer to step 6~11 for more details. 4. Check “Enable HTTPs”, click “Save”. The system will display the dialog box of “Need to reboot the device”, and then the config is valid. Figure 5-62 5. Use HTTPs Use HTTPs to log in. Enter https://xx.xx.xx.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-63 Note: “xx.xx.xx.xx” is corresponding to your IP or domain name. 5.3 Event 5.3.1 Video detection 5.3.1.1 Motion Detection Step 1 Select “Setup > Event > Video Detection > Motion Detection’ and the system will display the interface of “Motion Detection” which is shown in Figure 5-64.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-64 Step 2 Select “Enable” to enable motion detection function. Step 3 Set motion detection area. 1.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-65 2. Set area name, it is to set valid area of motion detection according to the actual situation, and it can set the value of sensitivity and threshold respectively. The bigger the sensitivity is, the easier it is to generate motion detection, the smaller the threshold is, the easier it is to generate motion detection; the entire video image is the valid area of motion detection by default.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Working Period Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function PTZ Snapshot Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm. The event type includes: preset, tour and pattern. You need to check the box here so that system can backup motion detection snapshot file. You shall set snapshot period in Storage>Schedule. Step 5 Click “Save” to complete the setting of motion detection. 5.3.1.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Working Period Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-67 Step 2 Check “Enable” to enable the function of scene changing. Step 3 It is to set the parameters of scene changing, please refer to the following sheet for more details. Parameter Function Working Period Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function PTZ Snapshot Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm. The event type includes: preset, tour and pattern. You need to check the box here so that system can backup motion detection snapshot file. You shall set snapshot period in Storage>Schedule. Step 4 Click “Save” to complete the setup of scene changing. 5.3.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Sensitivity It can be judged as audio abnormity when the input volume change exceeds continuous environment volume; users need to adjust according to the actual environment test. Threshold It is to set the filtered environment volume intensity, if the environmental noise is too big, then the value needs to be set higher, users can adjust according to the actual environment test.
Dahua Network Camera Web 3.0 Operation Manual 5.3.3 Smart Plan Smart plan is the master switch for intelligent analysis such as “Face Detection”, “Heat Map”, “IVS”, “People Counting” and so on, the corresponding intelligent functions can be valid after smart plan is enabled. Step 1 Select “Setup > Event > Smart Plan”. The system will display the interface of “Smart Plan”, which is shown in Figure 5-69. Figure 5-69 Step 2 Click “Save” to complete the config of smart plan. 5.3.
Dahua Network Camera Web 3.0 Operation Manual 5.3.4.1 IVS 5.3.4.1.1 Tripwire It will trigger alarm when the target crosses the warning line according to the movement direction which has been set. It needs some time from when the target appears to when the target is confirmed, so it has to leave some space on both sides of the warning line when setting the warning line, please do not set the warning line near the obstructions.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Object tracking Select “Object tracking” to enable the function, refer to “2.4 Video Window Adjustment” for more details. Note: The function is only supported by some models. Working Period Direction Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
Dahua Network Camera Web 3.0 Operation Manual Cross means that it will trigger alarm when the target enters or exits the area. Appears means that it will trigger alarm when the target appears in the area. As for the report interval of the IVS function in the area, the system will trigger an alarm if it detects same event happened during the interval; the alarm counter will become zero if there is no same event happened in the interval.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Object tracking Select “Object tracking” to enable the function, refer to “2.4 Video Window Adjustment” for more details. Note: The function is only supported by some models. Working Period Action Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2.
Dahua Network Camera Web 3.0 Operation Manual 5.3.4.3 Abandoned Object Abandoned object means the system will trigger alarm if the abandoned object in the monitoring scene exceeds the time which has been set by the users. Abandoned object and missing object can be confusing in a situation where both foreground and background are complicated. It also triggers alarm as abandoned object if there is pedestrian or vehicle staying still for too long.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Working Period Record Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Dahua Network Camera Web 3.0 Operation Manual Application scene: it can be applied to the scene where the target is sparse and there is no obvious and frequent light change. False alarm will be increased in the scene where the target density is high and there is frequent obstruction; the false alarm will be increased in the scene where there are more people staying. As for the detection area, try to make it simple, the function is not suitable for the area which is too complicated.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Working Period Record Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click “Setup” and the system will pop out the interface of “Working Period”. 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-74 Step 2 Select “Enable” to enable face detection function. Step 3 Click “Draw Target” to draw the size model of target filter in the video image. Step 4 It is to set the parameters of face detection, please refer to the following sheet for more details. Parameter Function Working Period Enable Face Enhancement Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Relay out Enable alarm activation function. You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs. Alarm Delay System can delay the alarm output for specified time after alarm ended. Send Email If you enabled this function, System can send out email to alert you when alarm occurs and ends. User can set email address in Network>SMTP.
Dahua Network Camera Web 3.0 Operation Manual Click “Draw Rule” to draw an area in the monitoring image. Step 4 Click “Draw Target” to draw the size model of filtered target in the video image. Step 5 It is to set the parameters of entrance and exit, please refer to the following sheet for more details. Parameter Function Installation Mode Select “Enable OSD” and it will display the people number statistics of entrance and exit in the monitoring image.
Dahua Network Camera Web 3.0 Operation Manual 5.3.6.2 Report It is to generate a form of report according to the number statistics. Step 1 Select “Setup > Event > People Counting > Report “and the system will display the interface of “Report’, which is shown in Figure 5-76. Figure 5-76 Step 2 It is to set search condition, please refer to the following sheet for more details.
Dahua Network Camera Web 3.0 Operation Manual Step 1 Select “Setup > Event > Heat Map > Heat Map” and the system will display the interface of “Heat Map”, which is shown in Figure 5-77. Figure 5-77 Step 2 Select “Enable” to enable heat map function. Step 3 It is to set the working period. 1. Click “Setup” and the system will display the interface of “Working Period”, which is shown in Figure 5-78.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-78 2. It is to set working period according to the following methods: You can input time numerical value or press the left mouse button to drag on the setup interface to set. There are six periods to be set every day, select the check box in front of the period, and then the period is valid.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-79 Step 2 It is to set begin time and end time. Step 3 Click “Search” to complete report statistics, click “Export” to export the statistics report. 5.3.8 Alarm Please note some series products do not support this function. 5.3.2.1 PIR alarm The alarm activation interface PIR alarm is shown as in figure 5-80.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-80 Please refer to the following sheet for detailed information. Parameter Function Enable After enabled, relay activation will work. Check it and enable the PIR alarm. Working period Anti-dither Flash Flash Delay This function becomes activated in the specified periods. There are six periods in one day. Please draw a circle to enable corresponding period. Select date. If you do not select, current setup applies to today only.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Relay out Enable alarm activation function. You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs. System can delay the alarm output for specified time after alarm ended. The value ranges from 10s to 300s. Alarm delay Send Email After this function is enabled, system can send out email to alert you when alarm occurs and ends.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function PTZ Check it and set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm. The event type includes: preset, tour and pattern and so on. 5.3.8.2 Flash Set Figure 5-82 Parameter Function ON/OFF ON means flash is on; OFF means flash is off. Weak-strong bar Via dragging this bar to adjust flash brightness. All Check and it means the day flash works. Period Period that flash is on. 5.3.8.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-83 parameter Function Enable Check it and enable audio detection. Threshold It will trigger alarm and set up a series of linkage when volume exceeds the set threshold. 5.3.9 Abnormity Abnormity includes No SD Card, Capacity Warning, SD Card Error, Disconnection, IP Conflict and Unauthorized Access. Note: Only device with SD card function has these three statuses: No SD card, capacity warning, and SD card error.
Dahua Network Camera Web 3.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-86 Please refer to the following sheet for detailed information. Parameter Function Enable Check to alarm when SD card is abnormal. Relay-out Check to enable relay-out alarm. Relay out delay The alarm output can delay for the specified time after alarm stops. The value ranges from 10s to 300s. Note: No SD card, capacity warning, SD card error, relay-out delay all start from alarm occurs.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-87 When login password keep been wrong for a few times, unauthorized access alarm occurs. This operation is similar to SD card error. Allow login error times as when it exceeds this limit, user account will be locked. Figure 5-88 5.4 Storage Management 5.4.1 Schedule Before schedule setup, user must set record mode is auto or manual. Note: If record mode in record control is off, then device will not snapshot according to schedule. 5.4.1.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-89 Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 5-90. Set period according to actual need. There are six periods available each day. By checking or unchecking, you can add or delete three types of record schedule: General, Motion, and Alarm. Note: Period setup can be done by dragging in record schedule interface while not releasing left mouse. Figure 5-90 Step 3.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-91 Step 4. In record schedule interface, click on OK. System prompts it is successfully saved. 5.4.1.2 Snapshot Schedule Snapshot setup as: Step 1. Click on Snapshot Schedule tab, see Figure 5-92. Figure 5-92 Step 2. From Monday to Sunday select snapshot time, click on setup on the right. See Figure 5-93. Set snapshot period according to actual need. There are six periods available each day.
Dahua Network Camera Web 3.0 Operation Manual By checking or unchecking, user can add or delete three types of snapshot schedule: General, Motion and Alarm. Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left mouse. Figure 5-93 Step 3. Click on OK, return to snapshot schedule interface. See Figure 5-94. Green color stands for the general record/snapshot. Yellow color stands for the motion detect record/snapshot.
Dahua Network Camera Web 3.0 Operation Manual 5.4.1.3 Holiday Schedule Holiday schedule can set specific date as holiday. Step 1. Click on Holiday Schedule tab, see Figure 5-95. Figure 5-95 Step 2. Select date to set as holiday. The selected date will be highlighted in yellow. Step 3. Check Record/Snapshot, click on Save. System prompts it is successfully saved. Step 4. Check Record Schedule/Snapshot Schedule interface, click on setup next to Holiday, and refer to setup of Monday to Sunday. Step 5.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-96 Please refer to the following sheet for detailed information. Parameter Function Event Type It includes: scheduled, motion detect and alarm. Local It saved in the SD card. FTP It saved in the FTP server. NAS It saved in NAS disk. 5.4.2.2 Local The local interface is shown as in Figure 5-97. Here you can view local Micro SD card or NAS disk information. You can also operate the read-only, write-only, hot swap and format operation.
Dahua Network Camera Web 3.0 Operation Manual 5.4.2.3 FTP The FTP interface is shown as in Figure 5-98. You need to check the box to enable the FTP function. When network disconnect occurred or there is malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Click the test button to check if the FTP server can be connected for test. Figure 5-98 5.4.2.4 NAS You need to check the box to enable the NAS function.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Remote Directory Set storage directory, videos and pictures can be stored in to corresponding server directory. 5.4.3 Record control The record control interface is shown as in Figure 5-100. Figure 5-100 Please refer to the following sheet for detailed information. Parameter Function Pack Duration Here you can select file size within 1min~120min. Default setup is 8 minutes. Pre-record Please input pre-record value here.
Dahua Network Camera Web 3.0 Operation Manual 5.5 System 5.5.1 General The General interface is shown as in Figure 5-101. Figure 5-101 Please refer to the following sheet for detailed information. Parameter Function Device Name It is to set device name. Note: Different devices have different names. Video Standard This is to display video standard such as PAL. Language You can select the language from the dropdown list.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-102 Please refer to the following sheet for detailed information. Parameter Function Date format Here you can select date format from the dropdown list. Time Format There are two options: 24-H and 12-H. Time zone The time zone of the device. Current Time It is to set system time. It becomes valid after you set. Sync PC You can click this button to save the system time as your PC current time.
Dahua Network Camera Web 3.0 Operation Manual 5.5.2 Account For user name and user group, the max length is 31 characters, which can be made up of digit, letter, underline, hyphen, dot and @. Password can be 0~32 characters in number and letter only. User can modify other user’s password. User and group can be manually added to 18 and 8 respectively. User management adopts group/user modes. The user name and the group name shall be unique. One user shall be included in only one group.
Dahua Network Camera Web 3.0 Operation Manual Please note the user rights shall not exceed the group right setup. For convenient setup, please make sure the general user has the lower rights setup than the admin. Figure 5-104 Modify user It is to modify the user property, belonging group, password and rights. See Figure 5-103. Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-105 5.5.2.2 Group The group management interface can add/remove group, modify group password and etc. The interface is shown as in Figure 5-106. Figure 5-106 Add group: It is to add group and set its corresponding rights. See Figure 5-107.
Dahua Network Camera Web 3.0 Operation Manual Please input the group name and then check the box to select the corresponding rights. It includes: preview, playback, record control, PTZ control and etc. Figure 5-107 Modify group Click the modify group button, you can see an interface is shown as in Figure 5-108. Here you can modify group information such as remarks and rights. Figure 5-108 5.5.3 PTZ Please note only some series products support this function.
Dahua Network Camera Web 3.0 Operation Manual The PTZ settings interface is shown as in Figure 5-109. Figure 5-109 Please refer to the following sheet for detailed information. Parameter Function Protocol Select the corresponding dome protocol. Address Set corresponding dome address. Default value is 1. Please note your setup here shall comply with your dome address; otherwise you cannot control the speed dome. Select the dome baud rate. Default setup is 9600. Baud Rate Data Bit Default setup is 8.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-110 5.5.5 Import/Export The interface is shown as in Figure 5-109. Figure 5-111 Please refer to the following sheet for detailed information. Parameter Function Import It is to import the local setup files to the system. Export It is to export the corresponding system setup to your local PC. 5.5.6 Remote control Note: It is supported by some devices.
Dahua Network Camera Web 3.0 Operation Manual Figure 5-112 Parameter Function Learn Bind remote control or wireless alarm with equipment. Clear Unbind remote control with equipment. Start arm after the time you choose, disarm comes into effect immediately. Note: Arm/Disarm With disarm status, all the following alarms won’t trigger: motion detect alarm, masking alarm, local alarm, PIR alarm, wireless alarm. 5.5.6 Auto Maintenance The auto maintenance interface is shown as in Figure 5-113.
Dahua Network Camera Web 3.0 Operation Manual Parameter Function Auto Reboot Check it and set auto reboot time. Auto Delete Old Files Check it and set period within 1~31 days. 5.5.7 Upgrade The upgrade interface is shown as in Figure 5-114. Please select the upgrade file (file extension is “.bin”) and then click the update button to begin firmware update. Important Improper upgrade program may result in device malfunction! Figure 5-114 5.6 Information 5.6.
Dahua Network Camera Web 3.0 Operation Manual 5.6.2 Log Here you can view system log. See Figure 5-116. Figure 5-116 Please refer to the following sheet for log parameter information. Parameter Function Start time Set the start time of the requested log. (The earliest time is 2000/1/1) End time Set the end time of the requested log. (The latest time is 2037/12/31) Type Search Log information Log type. You can select log type from the drop down list and then click search button to view the list.
Dahua Network Camera Web 3.
Dahua Network Camera Web 3.0 Operation Manual 6 Alarm Please note some series product does not support this function. Click alarm function, you can see an interface is shown as in Figure 6-1. Here you can set device alarm type and alarm sound setup. Figure 6-1 Please refer to the following sheet for detailed information. Type Parameter Function Alarm Motion detection System alarms when motion detection alarm type occurs, Disk full System alarms when disk is full.
Dahua Network Camera Web 3.0 Operation Manual Type Operation Parameter Prompt Alarm Tone Play Alarm Tone Tone Path Function When alarm is triggered, there will be s inmain menu of alarm interface and system automatically records alarm info. The icon disappears when user click on alarm menu bar. Note: If alarm interface is displayed, when alarm is triggered, there will be no image prompt, but alarm record will be in list on the right.
Dahua Network Camera Web 3.0 Operation Manual 7 Log out Click log out button, system goes back to log in interface. See Figure 7- 1. Figure 7- 1 Note: This manual is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. All trademarks and registered trademarks mentioned are the properties of their respective owners.
