User's Manual
Table Of Contents
- Foreword
- Important Safeguards and Warnings
- 1 Overview
- 2 Configuration Flow
- 3 Device Initialization
- 4 Basic Configuration
- 4.1 Login
- 4.2 Live
- 4.3 PTZ Operation
- 4.4 Playback
- 4.5 Camera
- 4.5.1 Conditions
- 4.5.2 Setting Video Parameters
- 4.5.2.1 Video
- 4.5.2.2 Snapshot
- 4.5.2.3 Overlay
- 4.5.2.3.1 Configuring Privacy Masking
- 4.5.2.3.2 Configuring Channel Title
- 4.5.2.3.3 Configuring Time Title
- 4.5.2.3.4 Configure Text Overlay
- 4.5.2.3.5 Configure Font Attribute
- 4.5.2.3.6 Configure Picture Overlay
- 4.5.2.3.7 Configure Custom Overlay
- 4.5.2.3.8 Configuring OSD Info
- 4.5.2.3.9 Configuring Counting
- 4.5.2.3.10 Configuring Structured Statistics
- 4.5.2.3.11 Configuring Ranging
- 4.5.2.3.12 Configuring ANPR
- 4.5.2.3.13 Configuring Face Statistics
- 4.5.2.4 ROI
- 4.5.2.5 Path
- 4.5.3 Audio
- 4.6 Network
- 4.7 Storage
- 4.8 System
- 5 Event
- 5.1 Setting Alarm Linkage
- 5.2 Setting Smart Track
- 5.3 Setting Panoramic Calibration
- 5.4 Setting Video Detection
- 5.5 Setting Smart Motion Detection
- 5.6 Setting Audio Detection
- 5.7 Setting Smart Plan
- 5.8 Setting IVS
- 5.9 Setting Crowd Map
- 5.10 Setting Face Recognition
- 5.11 Setting Face Detection
- 5.12 Setting People Counting
- 5.13 Setting Heat Map
- 5.14 Setting Stereo Analysis
- 5.15 Setting ANPR
- 5.16 Setting Video Structuralization
- 5.17 Setting Relay-in
- 5.18 Setting Abnormality
- 6 Maintenance
- Appendix 1 Cybersecurity Recommendations
User’s Manual
91
Table 4-32 Description of path parameters
Parameter
Description
Event Type
Select from Scheduled, Motion Detection and Alarm.
Local
Save in the internal SD card.
FTP
Save in the FTP server.
NAS
Save in the NAS (network attached storage).
Click Save. Step 3
Configure other path parameters on Destination, FTP or NAS interface. For details, Step 4
see "4.7.3 Setting Destination", "4.7.3.3 FTP" or "4.7.3.4 NAS."
4.7.3.2 Local
Display the information of the local SD card. You can set it as read only or read & write; you can
also hot swap and format SD card, and reset password for it. When inserting Dahua smart card
onto a device available for it, there are 3 modes according to the SD card status:
Normal mode: The new SD cards and the cards whose password are cleared successfully
show normal mode. The SD cards of this status do not support authorization operation.
Unauthorized mode: The SD card authorized by other devices shows unauthorized mode.
The SD cards of this status do not support operations of setting read only, read & write,
formatting and encryption.
Encrypted mode: The SD cards encrypted and authorized on this camera show encrypted
mode. The camera can record max. 10 pieces of encrypted SD information. When the
recorded videos exceed 10 pieces, the earliest ones will be overwritten.
Functions might vary with different models, and the actual product shall prevail.
If you enter the wrong password for five times when authorizing, modifying, and clearing
password, the camera will be locked for five minutes.
Make sure that the SD card has been authorized before recording and playback.
The health status of SD card:
Green: The health status is excellent.
Blue: The health status is good.
Orange: The health status is moderate.
Red: The health status is poor, and you need to replace the SD card.
Select Setting > Storage > Destination > Local, and then the Local interface is displayed.
See Figure 4-85.
Click Read Only, and then the SD card is set to read only.
Click Read & Write, and then the SD card is set to read & write.
Click Hot Swap, and then you can pull out the SD card.
Click Refresh, and then you can format the SD card.