Service Manual XGA COLOR MONITOR Model : L700C/L700CM L701C/L701CM L700CAV DAEWOO ELECTRONICS CO., LTD. http : //svc.dwe.co.
CONTENTS SAFETY PRECAUTIONS 1 GENERAL SAFETY INFORMATION 2 SERVICING PRECAUTIONS 3 TECHNICAL INFORMATION 6 GENERAL INFORMATION 7 PIN CONNECTOR 8 CAUTIONS FOR ADJUSTMENT AND REPAIR 8 OPERATION & ADJUSTMENT 9 ALIGNMENT PROCEDURE 21 TROUBLESHOOTING HINTS (L700C/L700CM/L701C/L701CM) 22 TROUBLESHOOTING HINTS (L700CAV) 29 BLOCK DIAGRAM 39 SCHEMATIC DIAGRAM 40 EXPLODED VIEW & MECHANICAL PARTS LIST 51 INFORMATION OF PART DESCRIPTION 52 ELECTRICAL PARTS LIST (L700C/L700CM/L701C/L701CM)
SAFETY PRECAUTIONS CAUTION: No modifications of any circuits should be attempted. Service work should be performed only after you are thoroughly familiar with all of the following safety checks and servicing guidelines. ◆ Safety Check Care should be taken while servicing the inverter that generates the high voltage to lighten CCFL of the LCD panel. ◆ Fire & Shock Hazard • Insert an isolation transformer between the analog color display and AC power line before servicing the chassis.
GENERAL SAFETY INFORMATION ◆ Terms in the manual CAUTION Statements identify conditions or practices that could result in damage to the equipment or other property. WARNING Statements identify conditions or practices that could result in personal injury or loss of life. ◆ Terms as marked on equipment CAUTION Statements indicate a personal injury hazard not immediately accessible as one reads the marking or a hazard which is properly included on the equipment itself.
SERVICING PRECAUTIONS CAUTION: Before servicing instruments covered by this service manual, its supplements, and addendum, please read and follow the SAFETY PRECAUTIONS of this manual. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First. ◆ General Servicing Precautions 1. Always unplug the AC power cord from the AC power source before: a.
◆ Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components are commonly called Electrostatically Sensitive (ES) Devices. The typical examples of ES devices are integrated circuits, some field-effect transistors, and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1.
FIGURE 1. USE SOLDERING IRON TO PRY LEADS ◆ IC Removal/Replacement Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines. ◆ Removal 1.
◆ Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board. 3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect the solder joints of the two “original” leads on the circuit board copper side.
GENERAL INFORMATION This TFT LCD monitor automatically scans all horizontal frequencies from 30KHz to 80KHz, and all vertical frequencies from 56Hz to 77Hz. This TFT LCD monitor supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics display when using the following graphics adapters : (VGA, Super VGA, VESA, XGA, SXGA and Apple Macintosh Video Card).
PIN CONNECTOR Pin Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue GND GND GND - Red GND - Green GND - Blue +5Vdc GND - H.Sync GND - V.Sync Bi-directional Data (SDA) Horizontal Sync Vertical Sync (VCLK) Data Clock (SCL) 1 6 10 15 Arrangement of 15-pin D-sub connector CAUTIONS FOR ADJUSTMENT AND REPAIR • The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure, described in the service manual is made by a visual check.
OPERATION AND ADJUSTMENT << L700C/L700CM >> Control Panel 1 POWER 2 POWER Indicator swithes the monitor on and off. shows both normal operation and power management status with power indicator light. 5 8 3 7 6 2 4 3 1 (*) 4 moves cursor to the right or low window in the OSD window and increases the value of any selected function. 5 SELECT moves cursor to the left or high window in the OSD window and decreases value of any selected function. 6 MENU turns the OSD window on.
Key Process MENU 1280X1024 80K UT L TY 75 UT L TY OSD OSD SELECT UT L TY EXIT SELECT SHARPNESS EXIT SHARPNESS EXIT OSD OFF HOT KEY AUTO AUTO TRACKING When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly.
<< L701C/L701CM >> Control Panel 1 POWER 2 POWER Indicator swithes the monitor on and off. shows both normal operation and power management status with power indicator light. 1 2 EXIT AUTO MENU SELECT 7 6 5 8 3 BRIGHTNESS 4 (*) moves cursor to the right or low window in the OSD window and increases the value of any selected function. 5 SELECT moves from top menu to sub menu in the OSD window and opens the function window for the selected icon.
Key Process MENU 1280X1024 80K UT L TY 75 UT L TY SELECT SELECT OSD UT L TY EXIT OSD SHARPNESS EXIT SHARPNESS EXIT OSD OFF HOT KEY AUTO AUTO TRACKING When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly.
<< L700CAV >> Control Panel 1 POWER 2 POWER Indicator swithes the monitor on and off. shows both normal operation and power management status with power indicator light. 5 8 3 7 6 2 (*) moves cursor to the right or low window in the OSD window and increases the value of any selected function. 5 SELECT moves from top menu to sub menu in the OSD window and opens the function window for the selected icon.
Key Process MENU 1280X1024 80K UT L TY 75 U T L TY OSD OSD SELECT UT L T Y EXIT SELECT SHARPNESS EXIT SHARPNESS EXIT OSD OFF HOT KEY AUTO AUTO TRACKING When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly.
Adjustment Procedure No Is the H.Size proper? Adjust the CLOCK control. Yes Is the noise displayed on the screen? Perform the AUTO POSITION. No Yes Perform the AUTO TRACKING. Is the noise displayed on the screen yet? No Yes Adjust the CLOCK FINE until the screen is cleared.
OSD Functions (L700C/L700CM/L701C/L701CM) ICON CONTROL FUNCTIONS LANGUAGE Select language for OSD (6 languages). CLOCK Adjust the width (horizontal size) of the screen image. CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen. AUTO TRACKING Adjust the horizontal & vertical picture image quality and size.
OSD Functions (L700CAV) << OSD FUNCTIONS WITH USING PC >> SOUND ; VOLUME Increase or decrease audio volume. BALANCE Balance audio sound. TREBLE Adjust high frequency response. BASS Adjust low frequency response. CLOCK Adjust the width (horizontal size) of the screen image. CLOCK CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen.
UTILITY OSD SHARPNESS Adjust the display image quality (if the screen proceed to scaling up). OSD POSITION Adjust the OSD position horizontally (left or right) and vertically (up or down). OSD TIME OUT Adjust the display OSD Menu. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. AUTO POSITION Choose automatically the proper horizontal position and vertical position & size of the screen image.
<< OSD FUNCTIONS WITH USING VIDEO >> VOLUME Increase or decrease audio volume. BRIGHTNESS Adjust the brightness of image. CONTRAST Adjust the contrast of image. COLOR SATURATION Adjust saturation of image. HUE Adjust the hues of image. SHARPNESS Adjust the display image quality (if the screen proceed to scaling up). BALANCE Balance audio sound. TREBLE Adjust high frequency response. BASS Adjust low frequency response.
Self Diagnosis If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is No Signal, Out of range or None support. “No Signal” screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode. “Out of Range” screen is displayed when the applied frequency is under or over normal range.
ALIGNMENT PROCEDURE Standard Check point 1. Power source : 100 - 240Vac, 50/60Hz. 2. Aging : Take at least 20 minutes warm-up time. 3. Signal Video input : Analog 0.7Vpp 75Ω terminal positive polarity Synchronizing : acceptable negative or positive at TTL level Max. Resolution : 1280 x 1024 a 75Hz Frequency Horizontal : 30KHz - 80KHz Vertical : 56Hz - 77Hz (available only non interlace mode) Adjustment 1. Sharpness set to 53% 2. Contrast set to 92% 3. Brightness set to 50% 4.
TROUBLESHOOTING HINTS (L700C/L700CM/L701C/L701CM) 1. Abnormal mode detect Abnormal mode detect Yes Is a input H-sync of ADC(pin 40, U13) correct? No Trouble in the H-sync input circuit. No Trouble in ADC. Yes Is waveform of pin 81 of ADC(U13) correct? Yes Trouble in Scaler(U9).
2. Trouble in Power on Is the Power LED toggled between on and off? On Refer to No video or No raster. Off Is the power cord well connected? No Check if the power switch is on position and Connect the power cord correctly. Yes Check the waveform of pin 8 of -com(U6). No Trouble in U7 & Q3 and its ambient circuit. No Check the power board (5VS of CON2). Yes Is 5VS line normal(pin 8 of CON2)? Yes Check on Scaler(U9).
3. No Raster Check the output of Q4 or pin 41 of U6. < 2.5 Trouble in Q5 or pin 41 of -com. > 2.5 Is 12V plugged in pin 1 of CN4A(power board)? No Check the output of D811(power board). Yes Is the output of inverter correct? No Yes Replace a LCD panal. 24 Replace the inverter.
4. One color is missing One color is missing Yes No Is the OSD color normal? Check the output signal of Scaler. Yes Is the input signal normal? No Check the video signal cable or R,G,B con-ass’y. Yes Are the R,G,B Digital values (every eight bits) correct on ADC output stage? No Yes Trouble in the soldering of R,G,B data lines from output of ADC to Scaler(U9). 25 Check the ambient circuit of ADC.
5. No Video Has display image only white? No Next page. Yes Check if the CON7 wafer is well connected at the LCD panel. No Connection trouble. Yes Is pin 5, 6, 7, 8 of Q5 5V? No Yes Check interface (to -com) of scalier (pin 71~78) and solding of CON7. 26 Check Q5, its ambient circuit and pin 42 of U6.
5-1. No Video Black Yes Is OSD normal? No 3. No raster Yes Is the contrast at its maximum? No Set the contrast up to Max. Yes Is the output of ADC correct? No Is the input of ADC correct? Yes Yes Next Page. No Check the video input signal. Replace the main board (or replace ADC). Yes Is the output of Scaler correct? No Is the input of Scaler correct? No Yes Yes Replace the main board (or replace ADC). Check If the CON 7 wafer is well connected at the LCD panel.
6. Power Problem Is the power cord well connected? Check if the power cord is correctly connected. No Yes Check 5VS, 5VD, 5VA 3.3V of CN2A. No Is No the output of D812 6.2V on power board? Yes Yes Check the main board. Check ambient circuit of IC801 on power board.
TROUBLESHOOTING HINTS (L700CAV) 1. Abnormal mode detect 1-1. Abnormal mode detect for PC Source Abnormal mode detect Yes Is a input H-sync of ADC(pin 40, U13) correct? No Trouble in the H-sync input circuit. No Trouble in ADC. Yes Is waveform of clock of ADC(pin81, U13) correct? Yes Trouble in Scaler(U9).
1. Abnormal mode detect 1-2. Abnormal mode detect for AV Source Abnormal mode detect Yes Is a input signal of Decoder (pin 10 at CVBS or pin 14, 18 at SVideo of U5)? No Check CON 4 and I/O Board. Yes Is clock of Decoder (pin 94, U5) 27MHz? No Yes Trouble in Scaler(U9). 30 Trouble in decoder(U5).
2. Trouble in Power on Is the Power LED toggled between on and off? On Refer to No video or No raster. Off Is the power cord well connected? No Check if the power switch is on position and Connect the power cord correctly. Yes Check the waveform of pin 8 of -com(U6). No Trouble in U7 & Q3 and its ambient circuit. No Check the power board (5VS of CON2). Yes Is 5VS line normal(pin 8 of CON2)? Yes Check on Scaler(U9).
3. No Raster Check the output of Q4 or pin 41 of U6. < 2.5 Trouble in Q5 or pin 41 of -com. > 2.5 Is 12V plugged in pin 1 of CN4A(power board)? No Check the output of D811(power board). Yes Is the output of inverter correct? No Yes Replace a LCD panal. 32 Replace the inverter.
4. One color is missing for PC Source One color is missing Yes Is the OSD color normal? No Check the output signal of Scaler. Yes Is the input signal normal? No Check the video signal cable or R,G,B con-ass’y. Yes Are the R,G,B Digital values (every eight bits) correct on ADC output stage? No Yes Trouble in the soldering of R,G,B data lines from output of ADC to Scaler(U9). 33 Check the ambient circuit of ADC.
5. No Video Has display image only white? No Next page. Yes Check if the CON7 wafer is well connected at the LCD panel. No Connection trouble. Yes Is pin 5, 6, 7, 8 of Q5 5V? No Yes Check interface (to -com) of scalier (pin 71~78) and solding of CON7. 34 Check Q5, its ambient circuit and pin 42 of U6.
5. No Video 5-1. No video for PC Source Black Yes Is OSD normal? No 3. No raster Yes Is the contrast at its maximum? No Set the contrast up to Max. Yes Is the output of ADC correct? No Is the input of ADC correct? Yes Yes Next Page. No Check the video input signal. Replace the main board (or replace ADC). Yes Is the output of Scaler correct? No Is the input of Scaler correct? No Yes Yes Replace the main board (or replace ADC). Check If the CON 7 wafer is well connected at the LCD panel.
5. No Video 5-2. No video for AV Source Black Yes Is OSD normal? No 3. No raster Yes Is the contrast at its maximum? No Set the contrast up to Max. Yes Is the output of Decoder(U5) correct? Is the input of Decoder(U5) correct? No Yes Yes Next Page. No Check the video input signal (or check the CON 4). Replace the main board (or replace Decoder(U5)). Yes Is the output of Scaler correct? No Is the input of Scaler correct? No Yes Yes Replace the main board (or replace Decoder).
6. Power Problem Is the power cord well connected? Check if the power cord is correctly connected. No Yes Check 5VS, 5VD, 5VA 3.3V of CN2A. Yes No Is No the output of D812 6.2V on power board? Yes Check the main board. Check ambient circuit of IC801 on power board.
7. Sound Problem No Sound Is Audio-in OK? (pin 10, 14 at PC Source and pin 9, 13 at AV Source No Check Audio-in jack(CN 11). Yes Is VDD(pin2) of Audio IC(IC 601) 9V? No Is input of 9V regulator(IC 602) 12V? Yes Yes No Change 9V Regulator (IC 602). Check power board Is Audio-out OK? Yes No Are SCL(pin 28), SDA (pin 27) OK? No Check speaker. Yes Change Audio IC(IC601). 38 Check CA 602.
39 I/O PCB (100 240V) AC INLET 48 ANALOG R/G/B Max-1280x1024 H-3180KHz V-55 77Hz D-SUB R/G/B SIGNAL 3 Hsync Pixel -CLK TMDS ON/OFF H/V SYNC. Hsync Pixel -CLK 9 YUV 4:2:2 16 2 Digital R/G/B(Serial) Max-1280x1024 H-3180KHz V-55 75Hz DVI(option) DIGITAL SIGNAL DD C 24C21 TMDS Sil151 (Option) 48 TMDS SIGNA L Scaler ASI311 74ACT14 Sync-Buffer ADC AD9884A AD C ON/ OFF R(8), G(8), B(8) Hsync MAIN PCB 24.
SCHEMATIC DIAGRAM VGA Analog Input Section 40
DTF Connection TMDS Section 41
Damping Networks Section 42
NTSL/PAL Decoder Section 43
Mysonweltrend Microcontroller Section 44
ASI 311 Section 45
ASI 311 Decoupling Caps Section 46
LCD Panel Interface Section 47
Power Distribution Section 48
Audio Interface Section 49
Analog ADC (AD9884A-140) Section 50
EXPLODED VIEW & MECHANICAL PARTS LIST 51
INFORMATION OF PART DESCRIPTION Important Safety Notice Components identified with the International Symbol have special characteristics important for safety. When replacing any components, use only manufacturer’s specified parts. Abbreviation of Description RESISTOR Description Tolerance F ± 1% J ± 5% K ± 10% M ± 20% G ± 2% Example: Fig & Index Part No Description Resistors RD-4Z820J Carbon : 82J HRFS472JBA Chip 4.7K OHM J R101 R30 CAPACITOR Description C D F J K P Z Tolerance ± 0.25pF ± 0.
ELECTRICAL PARTS LIST (L700C/L700CM/L701C/L701CM) The components identified by mark have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list.
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC C125 C126 C127 C128 C129 C130 C131 C132 C133 C134 C135 C137 C138 C14 C140 C141 C144 C145 C146 C147 C148 C149 C15 C150 C151 C153 C154 C155 C157 C158 C159 C16 C161 C162 C163 C164 C165 C167 C168 C169 C17 C171 C172 C173 C174 C175 C18 C181 C183 C19 C190 PART-CODE HCQK180JBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCEDC470MC HCEDC470MC HCFK104ZBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCEKF100MC HCFK104
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC PART-CODE C191 C192 C193 C194 C20 C201 C202 C203 C204 C21 C212 C216 C22 C23 C24 C25 C26 C27 C28 C30 C31 C32 C33 C34 C35 C36 C37 C39 C4 C40 C41 C42 C43 C5 C51 C6 C7 C73 C8 C9 CON7 FB13 FB14 FB16 FB17 FB18 FB19 FB20 FB21 FB22 FB23 HCFK104ZBA HCEEF101MD HCFK104ZBA HCFK104ZBA HCFK104ZBA HCEEF101MD HCFK104ZBA HCEEF101MD HCFK104ZBA HCBK393KBA HCEEF101MD HCEKF100MC HCBK392KBA HCBK223KBA HCFK104ZBA HC
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC FB24 FB25 FB26 FB28 FB29 FB30 FB31 FB34 FB36 FB37 FB4 FB40 FB5 Q1 Q2 Q3 Q4 Q5 R1 R10 R100 R101 R102 R104 R105 R106 R107 R108 R109 R11 R110 R111 R112 R113 R114 R115 R116 R12 R121 R122 R123 R124 R128 R129 R13 R130 R131 R132 R133 R134 R135 PART-CODE HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HRFT000JCA HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 TKTC3875
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC R136 R14 R142 R143 R16 R17 R18 R19 R2 R22 R24 R25 R26 R27 R28 R3 R4 R6 R67 R68 R69 R7 R70 R71 R72 R73 R74 R75 R76 R77 R8 R83 R84 R85 R88 R9 R92 R93 R94 R96 R97 R98 R99 RA10 RA12 RA14 RA16 RA18 RA2 RA20 RA22 PART-CODE HRFS102JBA HRFS332JBA HRFS472JBA HRFS102JBA HRFS121JBA HRFS121JBA HRFS121JBA HRFS151JBA HRFS000JBA HRFS151JBA HRFS102JBA HRFS000JBA HRFS000JBA HRFS000JBA HRFS000JBA HRFS102JBA HRFS3
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 2 3 3 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 2 3 3 3 3 LOC PART-CODE RA24 RA28 RA29 RA30 RA31 RA32 RA33 RA34 RA35 RA36 RA37 RA38 RA39 RA4 RA6 RA8 U1 U10 U11 U13 U14 U6S U7 U8 U9 Y3 Z2030 CN901 LED1 Z3040 SW901 SW902 SW903 SW904 SW905 SW906 SW907 Z4040 PCB R901 R902 R903 R904 R905 R906 R907 Z2040 C801 C802 C807 C824 HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E
LEVEL 3 3 3 3 3 4 4 4 4 3 4 4 4 3 3 3 3 3 3 3 4 4 4 3 3 3 3 3 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 LOC PART-CODE CN2A CN4A CN6A D801 D811 00010 00020 D811 IC802 D812 00010 00020 D812 D813 IC803 IC804 IC811 L801 L811 Q801 00010 00020 Q801 T801 TH801 YFR10 YFR20 Z4010 C835 C838 C845 C850 C851 IC801 Z5010 C803 C805 C808 C809 C811 C812 C813 C843 C844 C848 C859 IC805 Q802 Q810 Z6010 B801 99707A0024 9970750037 9979200203 DD3SBA60-PCHCSWJ184 9977031900 9976012700 DFMLG22S-1KA278R05PCHASWJ184 997702830
LEVEL 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 LOC D805 D807 D809 DZ803 DZ806 J803 J805 J806 J807 J808 J811 J812 J815 J819 J821 J823 J825 J827 J828 J829 J830 J832 J836 J837 J838 J839 J841 J842 J843 J844 J845 PCB1 R801 R803 R804 R805 R806 R807 R809 R812 R813 R814 R815 R820 R822 R825 R826 R827 R832 R837 R839 PART-CODE DZN4148--DUF4007--DUG2D----DDZ22BM--DGDZJ18C-85801065GY 85801065GY 85801065GY 85801065GY 85801065GY 85801065GY 85801065GY 85801065G
LEVEL 6 6 6 6 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 1 2 2 2 2 2 1 2 1 2 2 2 2 2 2 2 2 LOC R840 R841 R854 R855 Z2050 CA601 CN6 CN7 F801 J601 YSB10 YSB20 YSB30 Z4020 C606 C607 C608 F801A F801B Z5020 D601 D602 D606 D607 D608 DZ602 DZ603 DZ604 DZ605 DZ606 DZ607 PCB Z1020 YR010 YR020 YR030 YR040 YR050 Z1030 YST10 Z1040 YP010 YP020 YP030 YP040 YP050 YP060 YP070 YP080 PART-CODE RN-AZ6491F RD-AZ102JRD-AZ102JRD-4Z512JPCDSSWJ191(192) 99707C0017 9970720090 9979200317 5F3CB3122L 9979200207 997392430
ELECTRICAL PARTS LIST (L700CAV) The components identified by mark have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list.
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC C12 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C13 C130 C131 C132 C133 C134 C135 C138 C14 C141 C144 C145 C146 C147 C148 C149 C15 C150 C151 C153 C154 C155 C157 C158 C159 C161 C162 C163 C164 C165 C167 C168 C169 C17 C171 C172 C173 C174 C175 C181 PART-CODE HCFH473ZBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCQK100JBA HCQK100JBA HCQK100JBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCEDC470MC HCFK104ZBA HCEDC4
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC C183 C190 C191 C192 C193 C194 C20 C201 C202 C203 C204 C21 C212 C216 C23 C24 C25 C26 C27 C28 C30 C31 C32 C34 C35 C36 C37 C38 C39 C4 C40 C42 C5 C51 C6 C68 C69 C7 C70 C71 C72 C73 C74 C75 C76 C77 C78 C79 C8 C80 C81 PART-CODE HCEDC470MC HCEEF101MD HCFK104ZBA HCEEF101MD HCFK104ZBA HCFK104ZBA HCFK104ZBA HCEEF101MD HCFK104ZBA HCEEF101MD HCFK104ZBA HCFK104ZBA HCEEF101MD HCEKF100MC HCBK223KBA HCFK104ZBA H
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC PART-CODE PART-NAME PART-DESC C82 C83 C84 C85 C86 C88 C9 C90 C92 C93 C94 C95 C97 C98 C99 CON7 FB11 FB12 FB13 FB14 FB15 FB16 FB17 FB18 FB19 FB2 FB20 FB21 FB22 FB23 FB24 FB25 FB26 FB28 FB29 FB30 FB31 FB34 FB36 FB37 FB4 FB40 L1 Q1 Q2 Q3 Q4 Q5 R10 R100 R101 HCFK104ZBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCFH473ZBA HCFH473ZBA HCFK104ZBA HCFH473ZBA HCQK200JBA HCQK200JBA HCFH473ZBA HCBK102KBA HCFH473Z
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC R102 R104 R105 R106 R107 R108 R109 R11 R110 R111 R112 R113 R114 R115 R116 R118 R119 R12 R121 R122 R123 R124 R128 R129 R13 R130 R131 R132 R133 R134 R135 R136 R14 R142 R143 R16 R17 R18 R19 R2 R20 R21 R22 R24 R25 R26 R27 R28 R4 R48 R49 PART-CODE HRFS472JBA HRFS000JBA HRFS102JBA HRFS101JBA HRFS101JBA HRFS472JBA HRFS472JBA HRFS750JBA HRFS472JBA HRFS101JBA HRFS101JBA HRFS102JBA HRFS102JBA HRFS223JBA H
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC R50 R51 R52 R53 R54 R55 R57 R58 R59 R6 R60 R64 R65 R66 R67 R68 R69 R7 R70 R71 R72 R73 R74 R75 R76 R77 R8 R83 R84 R85 R88 R9 R92 R93 R94 R96 R97 R98 R99 RA10 RA12 RA14 RA16 RA18 RA2 RA20 RA22 RA24 RA26 RA27 RA28 PART-CODE HRFS180JBA HRFS560JBA HRFS180JBA HRFS560JBA HRFS180JBA HRFS560JBA HRFS180JBA HRFS560JBA HRFS330JBA HRFS223JBA HRFS332JBA HRFS332JBA HRFS332JBA HRFS332JBA HRFS472JBA HRFS472JBA H
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 2 3 3 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 2 3 3 3 3 LOC PART-CODE RA29 RA30 RA31 RA32 RA33 RA34 RA35 RA36 RA37 RA38 RA39 RA4 RA6 RA8 U1 U10 U11 U13 U14 U5 U6S U7 U8 U9 Y1 Y3 Z2030 CN901 LED1 Z3040 SW901 SW902 SW903 SW904 SW905 SW906 SW907 Z4040 PCB R901 R902 R903 R904 R905 R906 R907 Z2040 C801 C802 C807 C824 HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E330J HRTS8E101J HRTS8E101J
LEVEL 3 3 3 3 3 4 4 4 4 3 4 4 4 4 3 3 3 3 3 3 4 4 4 4 3 3 3 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 LOC PART-CODE CN2A CN4A CN6A D801 D811 00010 00020 D811 IC802 D812 00010 00020 D812 IC803 D813 IC804 IC811 L801 P001 Q801 00010 00020 00030 Q801 T801 TH801 Z3040 C835 C838 C839 C845 C850 C851 C855 C860 IC801 Z4040 C803 C805 C808 C809 C811 C812 C813 C843 C844 C848 IC805 L811 Q802 Q810 99707A0024 9970750037 9979200203 DD3SBA60-PCHCSWJ184 9977031900 9976012700 DFMLG22S-1KA278R05PCHASWJ210 9977031900
LEVEL 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 LOC Z5040 B801 D802 D805 D807 D809 DZ803 DZ806 J803 J805 J806 J807 J808 J811 J819 J823 J825 J827 J828 J830 J841 J842 J843 J847 J848 J849 J851 J852 J854 J856 PCB1 R801 R803 R804 R805 R806 R807 R809 R812 R813 R814 R815 R820 R822 R825 R826 R827 R832 R837 R839 R840 PART-CODE PCSMJAJ198 5PB13857-DUG2D----DZN4148--DUF4007--DUG2D----DDZ22BM--DGDZJ18C-85801065GY 85801065GY 85801065GY 85801065GY 85801065GY 8
LEVEL 6 6 6 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 LOC PART-CODE R841 R854 R855 Z2050 CA601 CA602 CN6 CN7 F801 F801A F801B IC604 J601 J602 J604 J605 J606 YSB10 YSB20 YSB30 Z4020 C601 C603 C604 C605 C606 C607 C608 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C623 C624 C625 C632 C635 C639 D601 D602 D606 D607 RD-AZ102JRD-AZ102JRD-4Z512JPCDSSWJ184 99707C0017 9970780034 9970720090 9979200317 5F3CB3122L 9977410900 9977410900 1KA78R09
LEVEL 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1 2 2 2 2 2 1 2 1 2 2 2 2 2 2 2 2 LOC D608 DZ601 DZ602 DZ603 DZ604 DZ605 DZ606 DZ607 DZ608 DZ609 IC603 PCB R601 R602 R603 R604 R605 R606 R607 R608 R609 R610 Z1020 YR010 YR020 YR030 YR040 YR050 Z1030 YST10 Z1040 YP010 YP020 YP030 YP040 YP050 YP060 YP070 YP080 PART-CODE DRLS4148-DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B DRLZ5R6B-B 1PT2313L-9979800591 HRFS101JBA HRFS101JBA HRFS242JBA HRFS242JBA HRFS242JBA HRFS242J
