Service Manual XGA COLOR MONITOR ht tp :// ww w. wj el. ne t Model : L700C/L700CM L701C/L701CM L700CAV DAEWOO ELECTRONICS CO., LTD. http : //svc.dwe.co.
jel .w :// ww w 资料库 转载请注明出处 ht tp http://scwj.8800.org http://wjbbs.mpc.
SERVICING PRECAUTIONS CAUTION: Before servicing instruments covered by this service manual, its supplements, and addendum, please read and follow the SAFETY PRECAUTIONS of this manual. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First. ◆ General Servicing Precautions el. ne t 1.
◆ Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components are commonly called Electrostatically Sensitive (ES) Devices. The typical examples of ES devices are integrated circuits, some field-effect transistors, and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1.
t ne FIGURE 1. USE SOLDERING IRON TO PRY LEADS el. ◆ IC Removal/Replacement w. wj Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.
◆ Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board. 3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect the solder joints of the two “original” leads on the circuit board copper side.
GENERAL INFORMATION This TFT LCD monitor automatically scans all horizontal frequencies from 30KHz to 80KHz, and all vertical frequencies from 56Hz to 77Hz. This TFT LCD monitor supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics display when using the following graphics adapters : (VGA, Super VGA, VESA, XGA, SXGA and Apple Macintosh Video Card).
PIN CONNECTOR 1 6 10 15 Arrangement of 15-pin D-sub connector t Red Green Blue GND GND GND - Red GND - Green GND - Blue +5Vdc GND - H.Sync GND - V.Sync Bi-directional Data (SDA) Horizontal Sync Vertical Sync (VCLK) Data Clock (SCL) ne 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 el. Signal w. wj Pin CAUTIONS FOR ADJUSTMENT AND REPAIR :// ww • The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure, described in the service manual is made by a visual check.
OPERATION AND ADJUSTMENT << L700C/L700CM >> Control Panel 1 POWER 2 POWER Indicator swithes the monitor on and off. 4 3 8 6 (*) 2 1 4 ww 3 7 w. wj el. ne 5 t shows both normal operation and power management status with power indicator light. moves cursor to the left or high window in the OSD window and decreases value of any selected function. 6 MENU turns the OSD window on.
Key Process MENU 1280X1024 80K UT L TY 75 UT L TY OSD OSD SELECT EXIT SHARPNESS EXIT SHARPNESS w. wj el. UT L TY ne t SELECT EXIT ww OSD OFF tp AUTO :// HOT KEY When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. ht AUTO TRACKING BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly.
<< L701C/L701CM >> Control Panel 1 POWER 2 POWER Indicator swithes the monitor on and off. shows both normal operation and power management status with power indicator light. 1 AUTO MENU SELECT 7 6 5 3 4 3 ww 8 BRIGHTNESS w. wj EXIT el. ne t 2 (*) 4 tp :// moves cursor to the right or low window in the OSD window and increases the value of any selected function. 5 SELECT 6 MENU turns the OSD window on.
Key Process MENU 1280X1024 80K UT L TY 75 UT L TY SELECT SELECT OSD el. ne t OSD EXIT SHARPNESS EXIT SHARPNESS w. wj UT L TY EXIT ww OSD OFF tp AUTO :// HOT KEY ht AUTO TRACKING When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly.
<< L700CAV >> Control Panel 1 POWER 2 POWER Indicator swithes the monitor on and off. shows both normal operation and power management status with power indicator light. 3 t 4 8 (*) 6 2 1 ww 3 7 w. wj el. ne 5 4 :// moves cursor to the right or low window in the OSD window and increases the value of any selected function. 5 SELECT ht tp moves from top menu to sub menu in the OSD window and opens the function window for the selected icon.
Key Process MENU 1280X1024 80K UT L TY 75 U T L TY OSD OSD SELECT EXIT SHARPNESS EXIT SHARPNESS w. wj el. UT L T Y ne t SELECT EXIT ww OSD OFF tp AUTO :// HOT KEY ht AUTO TRACKING When there is no OSD, if you press this AUTO button, you can use the best display performance fit for a current mode. BRIGHTNESS When there is no OSD, if you press this BRIGHTNESS button, you can adjust the brightness directly.
Adjustment Procedure No Is the H.Size proper? Adjust the CLOCK control. t Yes Perform the AUTO POSITION. ne Is the noise displayed on the screen? el. No ww Perform the AUTO TRACKING. w. wj Yes Is the noise displayed on the screen yet? :// No tp Yes ht Adjust the CLOCK FINE until the screen is cleared.
OSD Functions (L700C/L700CM/L701C/L701CM) ICON CONTROL FUNCTIONS Select language for OSD (6 languages). CLOCK Adjust the width (horizontal size) of the screen image. CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen. AUTO TRACKING Adjust the horizontal & vertical picture image quality and size.
OSD Functions (L700CAV) << OSD FUNCTIONS WITH USING PC >> SOUND BALANCE Balance audio sound. TREBLE Adjust high frequency response. BASS Adjust low frequency response. CLOCK Adjust the width (horizontal size) of the screen image. ne Adjust the horizontal & vertical picture image quality and size. :// AUTO TRACKING Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp.
UTILITY OSD POSITION Adjust the OSD position horizontally (left or right) and vertically (up or down). OSD TIME OUT Adjust the display OSD Menu. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. AUTO POSITION Choose automatically the proper horizontal position and vertical position & size of the screen image. LANGUAGE ne el. w. wj Select language for OSD (6 languages).
<< OSD FUNCTIONS WITH USING VIDEO >> Increase or decrease audio volume. BRIGHTNESS Adjust the brightness of image. CONTRAST Adjust the contrast of image. t VOLUME ne COLOR Adjust saturation of image. HUE Adjust the hues of image. SHARPNESS Adjust the display image quality (if the screen proceed to scaling up). BALANCE Balance audio sound. w. wj ww SOUND Adjust high frequency response. Adjust low frequency response. ht tp :// TREBLE BASS el.
Self Diagnosis If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is No Signal, Out of range or None support. “No Signal” screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode. ne el. Normal range (Non-interlaced mode only) H : 30 - 80 KHz V : 56 - 77 Hz t “Out of Range” screen is displayed when the applied frequency is under or over normal range.
ALIGNMENT PROCEDURE Standard Check point Adjustment ht tp :// ww w. wj el. 1. Sharpness set to 53% 2. Contrast set to 92% 3. Brightness set to 50% 4. Switching to factory alignment mode Press power key with Brightness left key at the power off status. 5. Video level adjustment Receive stair pattern of 16 step (doesn’t care any mode). Readjust coarse R, G, B in AD9884A menu before saturaton point. (SG9884A : L700CAV) 6. Set up the tracking See the user’s manual at page 8th. 7.
TROUBLESHOOTING HINTS (L700C/L700CM/L701C/L701CM) 1. Abnormal mode detect Abnormal mode detect Yes No Trouble in the H-sync input circuit. Yes Yes ht tp :// ww Trouble in Scaler(U9). No Trouble in ADC. w. wj Is waveform of pin 81 of ADC(U13) correct? el.
2. Trouble in Power on Is the Power LED toggled between on and off? On Refer to No video or No raster. No ww Yes w. wj Yes Check the waveform of pin 8 of -com(U6). No :// Is 5VS line normal(pin 8 of CON2)? Check if the power switch is on position and Connect the power cord correctly. el. No ne Is the power cord well connected? t Off tp Yes ht Check on Scaler(U9). 23 Trouble in U7 & Q3 and its ambient circuit. Check the power board (5VS of CON2).
3. No Raster Check the output of Q4 or pin 41 of U6. < 2.5 Trouble in Q5 or pin 41 of -com. Check the output of D811(power board). w. wj Yes Is the output of inverter correct? No ww Yes ne No el. Is 12V plugged in pin 1 of CN4A(power board)? t > 2.5 ht tp :// Replace a LCD panal. 24 Replace the inverter.
4. One color is missing One color is missing Yes No Check the output signal of Scaler. Yes Is the input signal normal? Check the video signal cable or R,G,B con-ass’y. w. wj Yes No el. ne t Is the OSD color normal? Are the R,G,B Digital values (every eight bits) correct on ADC output stage? ww No :// Yes ht tp Trouble in the soldering of R,G,B data lines from output of ADC to Scaler(U9). 25 Check the ambient circuit of ADC.
5. No Video Has display image only white? No Next page. Connection trouble. w. wj Yes No ww Is pin 5, 6, 7, 8 of Q5 5V? ne No el. Check if the CON7 wafer is well connected at the LCD panel. t Yes Yes ht tp :// Check interface (to -com) of scalier (pin 71~78) and solding of CON7. 26 Check Q5, its ambient circuit and pin 42 of U6.
5-1. No Video Black Yes No 3. No raster ne t Is OSD normal? No tp Next Page. Is the input of ADC correct? Yes No :// Yes Set the contrast up to Max. ww Yes Is the output of ADC correct? No w. wj Is the contrast at its maximum? el. Yes Check the video input signal. Replace the main board (or replace ADC). ht Yes Is the output of Scaler correct? No Is the input of Scaler correct? No Yes Yes Replace the main board (or replace ADC).
6. Power Problem Is the power cord well connected? Check if the power cord is correctly connected. No Check 5VS, 5VD, 5VA 3.3V of CN2A. ne t Yes No el. Is No the output of D812 6.2V on power board? w. wj Yes Yes Check the main board. ht tp :// ww Check ambient circuit of IC801 on power board.
TROUBLESHOOTING HINTS (L700CAV) 1. Abnormal mode detect 1-1. Abnormal mode detect for PC Source Abnormal mode detect Yes ne Yes Yes ht tp :// ww Trouble in Scaler(U9). No Trouble in ADC. w. wj Is waveform of clock of ADC(pin81, U13) correct? Trouble in the H-sync input circuit. t No el.
1. Abnormal mode detect 1-2. Abnormal mode detect for AV Source Abnormal mode detect w. wj Yes Is clock of Decoder (pin 94, U5) 27MHz? No ww Yes Check CON 4 and I/O Board. ne No el. Is a input signal of Decoder (pin 10 at CVBS or pin 14, 18 at SVideo of U5)? t Yes ht tp :// Trouble in Scaler(U9). 30 Trouble in decoder(U5).
2. Trouble in Power on Is the Power LED toggled between on and off? On Refer to No video or No raster. t Off No ww Yes w. wj Yes Check the waveform of pin 8 of -com(U6). No :// Is 5VS line normal(pin 8 of CON2)? Check if the power switch is on position and Connect the power cord correctly. el. No ne Is the power cord well connected? ht tp Yes Check on Scaler(U9). 31 Trouble in U7 & Q3 and its ambient circuit. Check the power board (5VS of CON2).
3. No Raster Check the output of Q4 or pin 41 of U6. < 2.5 Trouble in Q5 or pin 41 of -com. Is 12V plugged in pin 1 of CN4A(power board)? Check the output of D811(power board). el. No ne t > 2.5 w. wj Yes Is the output of inverter correct? ww No Yes ht tp :// Replace a LCD panal. 32 Replace the inverter.
4. One color is missing for PC Source One color is missing Yes No ne Is the input signal normal? Check the video signal cable or R,G,B con-ass’y. w. wj No el. Yes Yes Check the output signal of Scaler. t Is the OSD color normal? ww Are the R,G,B Digital values (every eight bits) correct on ADC output stage? :// No Yes ht tp Trouble in the soldering of R,G,B data lines from output of ADC to Scaler(U9). 33 Check the ambient circuit of ADC.
5. No Video Has display image only white? No Next page. Check if the CON7 wafer is well connected at the LCD panel. w. wj Yes No ww Is pin 5, 6, 7, 8 of Q5 5V? Connection trouble. el. No ne t Yes Yes ht tp :// Check interface (to -com) of scalier (pin 71~78) and solding of CON7. 34 Check Q5, its ambient circuit and pin 42 of U6.
5. No Video 5-1. No video for PC Source Black Yes No No Set the contrast up to Max. w. wj Is the contrast at its maximum? ww Yes No :// Yes el. Yes Is the output of ADC correct? t 3. No raster ne Is OSD normal? tp Next Page. Is the input of ADC correct? Yes No Check the video input signal. Replace the main board (or replace ADC). ht Yes Is the output of Scaler correct? No Is the input of Scaler correct? No Yes Yes Replace the main board (or replace ADC).
5. No Video 5-2. No video for AV Source Black No 3. No raster ne Is OSD normal? No w. wj Set the contrast up to Max. ww Yes el. Yes Is the contrast at its maximum? Is the output of Decoder(U5) correct? :// tp Is the input of Decoder(U5) correct? No Yes Next Page. t Yes Yes No Check the video input signal (or check the CON 4). Replace the main board (or replace Decoder(U5)).
6. Power Problem Is the power cord well connected? Check if the power cord is correctly connected. No Check 5VS, 5VD, 5VA 3.3V of CN2A. ne t Yes No el. Is No the output of D812 6.2V on power board? Check the main board. w. wj Yes Yes ht tp :// ww Check ambient circuit of IC801 on power board.
7. Sound Problem No Check Audio-in jack(CN 11). ne Is Audio-in OK? (pin 10, 14 at PC Source and pin 9, 13 at AV Source Is input of 9V regulator(IC 602) 12V? w. wj No el. Yes Is VDD(pin2) of Audio IC(IC 601) 9V? Yes Yes t No Sound No Change 9V Regulator (IC 602). No :// Is Audio-out OK? ww Check power board tp Yes Are SCL(pin 28), SDA (pin 27) OK? No ht Check speaker. Yes Change Audio IC(IC601). 38 Check CA 602.
LVDS DATA(12) CLOCK(4) R(8),G(8),B(8) jel 3 14.318 MHz TMDS SIGNA L YUV 4:2:2 9 48 48 Hsync Pixel -CLK DECODER ON/OFF Hsync Pixel -CLK 39 I/O PCB D-SUB AC INLET (100 240V) ANALOG R/G/B Max-1280x1024 H-3180KHz V-55 77Hz 74ACT14 Sync-Buffer H/V SYNC.
SCHEMATIC DIAGRAM ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ne el. .
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
ht tp :// ww w .w j el.
INFORMATION OF PART DESCRIPTION Important Safety Notice Components identified with the International Symbol have special characteristics important for safety. When replacing any components, use only manufacturer’s specified parts. Abbreviation of Description ne t RESISTOR Description Tolerance F ± 1% J ± 5% K ± 10% M ± 20% G ± 2% Fig & Index Part No Description R30 ww CAPACITOR Description ht tp :// Tolerance ± 0.25pF ± 0.
ELECTRICAL PARTS LIST (L700C/L700CM/L701C/L701CM) The components identified by mark have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list. 53 NOTE t CML-700C(L700CM) 12507HS-30+FI-X30H+20276=220(LVDS) 0.12*3*16+35750-0910*2=80 L170E3 EC-5 CML-700C C/FRONT AS E.G.I T=0.
PART-DESC NOTE 50V CH 18PF J 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 6.3V 47MF 5DX5.2H MV 6.3V 47MF 5DX5.2H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 10MF D4.0XH5.2 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 10MF D4.0XH5.2 50V Y5V 0.1MF Z 1608 MV 6.3V 47MF 5DX5.2H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 10MF D4.0XH5.2 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.
PART-NAME NOTE 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 50V X7R 0.039MF K 1608 MV 16V 100MF M 6.3DX5.7H MV 16V 10MF D4.0XH5.2 50V X7R 3900PF K 1608 50V X7R 0.022MF K 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V CH 100PF J 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 10MF D4.0XH5.2 MV 16V 10MF D4.0XH5.2 50V Y5V 0.
HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT 1/10 0 OHM J 2012 HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT HH-1M3216-601JT KTC3875SY(RTK) KTC3875SY(RTK) KTC3875SY(RTK) KTC3875SY(RTK) FDS4435A 1/16 33 OHM J 1608 1/16 75 OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 0 OHM J 1608 1/16 1K OHM J 1608 1/16 100 OHM J 1608 1/16 100 OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.
t NOTE el. ne 1/16 1K OHM J 1608 1/16 3.3K OHM J 1608 1/16 4.7K OHM J 1608 1/16 1K OHM J 1608 1/16 120 OHM J 1608 1/16 120 OHM J 1608 1/16 120 OHM J 1608 1/16 150 OHM J 1608 1/16 0 OHM J 1608 1/16 150 OHM J 1608 1/16 1K OHM J 1608 1/16 0 OHM J 1608 1/16 0 OHM J 1608 1/16 0 OHM J 1608 1/16 0 OHM J 1608 1/16 1K OHM J 1608 1/16 33 OHM J 1608 1/16 22K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 33 OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.
NOTE ne t 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 74ACT14SCX NT7181F NT7181F AD9884A-140 LM1117 PLCC 1.27PT 44PIN(22*22) KIA7042AF CAT24WC08 J AS1311 HC-49/SM5H 14.
PART-NAME 59 NOTE ne t 35164+YDH200+2464#24=150 5264+35164+2464#24=135 YW396-03AV D3SBA60 CML-700C AL T=2.0 TT2 BIN 3*8 MFZN PW(D0.7) FML-G22S KA278R05 CML-700C A1050P-H24 H=29 TT2 BIN 3*8 MFZN PW(D0.7) FML-G22S FMB-G19L KA278R33 TLP721D4GR KA78R05 DLF-2323 BFD 3512 R2 CML-700C A1050P-H24 H=21.5 TT2 BIN 3*8 MFZN PW(D0.7) SSS6N70A DMT-700C TP8D13 E.G.I T=0.8 TT2 BIN 3X6 MFZN CML-700C 25V RMU 1000MF (10*20) 16V RSS 470MF (10X12.5)TP 16V RUS 1000MF (10X20) TP 16V RSS 470MF (10X12.
PART-DESC NOTE 1N4148 AUTO 52MM UF4007 UG2D 200V 2A DZ22BM GDZJ 18C AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.
NOTE ne t 1/6W 6.49K OHM F (TP) 1/6 1K OHM J 1/6 1K OHM J 1/4 5.1K OHM J CML-700C(L700CM) YDH200-12+YBNH200-14+2990 9C=175(RGB) YH396-03V+35404-9002+1617#22=70 ST-03B-BP SEMKO TL 3.15AH 250V MF51 15P DDC BLUE W/OUT SCREW E.G.I. T=1.0 P.C T=0.5 (L520BM) TT2 BIN 3X6 MFZN CML-700C(L700CM) 50V CH 12PF J (TAPPING) 50V CH 12PF J (TAPPING) 50V CH 12PF J (TAPPING) BSP3-H T0.4 SN 5.2 BSP3-H T0.4 SN 5.2 CML-700C(L700CM) 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM 1N4148 AUTO 52MM DZ-5.
ELECTRICAL PARTS LIST (L700CAV) The components identified by mark have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list.
25V Y5V 0.047MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V CH 10PF J 1608 50V CH 10PF J 1608 50V CH 10PF J 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 6.3V 47MF 5DX5.2H 50V Y5V 0.1MF Z 1608 MV 6.3V 47MF 5DX5.2H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 6.3V 47MF 5DX5.2H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.
PART-DESC MV 6.3V 47MF 5DX5.2H MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 100MF M 6.3DX5.7H MV 16V 10MF D4.0XH5.2 50V X7R 0.022MF K 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V CH 100PF J 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 50V Y5V 0.1MF Z 1608 MV 16V 10MF D4.0XH5.2 MV 16V 10MF D4.
HCFK104ZBA HCFK104ZBA HCFK104ZBA HCFK104ZBA HCFH473ZBA HCFH473ZBA HCFK104ZBA HCFH473ZBA HCQK200JBA HCQK200JBA HCFH473ZBA HCBK102KBA HCFH473ZBA HCFH473ZBA HCFH473ZBA 9979220152 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HRFT000JCA HFFHH1M601 HFFHH1M601 HFFHH1M601 HFFHH1M601 HLCF1103MT TKTC3875SY TKTC3875SY TKTC3875SY TKTC38
t el. ne 1/16 4.7K OHM J 1608 1/16 0 OHM J 1608 1/16 1K OHM J 1608 1/16 100 OHM J 1608 1/16 100 OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 75 OHM J 1608 1/16 4.
t el. ne 1/16 18 OHM J 1608 1/16 56 OHM J 1608 1/16 18 OHM J 1608 1/16 56 OHM J 1608 1/16 18 OHM J 1608 1/16 56 OHM J 1608 1/16 18 OHM J 1608 1/16 56 OHM J 1608 1/16 33 OHM J 1608 1/16 22K OHM J 1608 1/16 3.3K OHM J 1608 1/16 3.3K OHM J 1608 1/16 3.3K OHM J 1608 1/16 3.3K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 33 OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.7K OHM J 1608 1/16 4.
ne t 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 33 OHM 3216 1/16 8P 100 OHM 3216 1/16 8P 100 OHM 3216 1/16 8P 100 OHM 3216 74ACT14SCX NT7181F NT7181F SG9884A-1401 LM1117 SAA7114H PLCC 1.27PT 44PIN(22*22) KIA7042AF CAT24WC08 J AS1311 HC-49/SMD 24.576MHZ 20PF HC-49/SM5H 14.
PART-NAME ne t 35164+YDH200+2464#24=150 5264+35164+2464#24=135 YW396-03AV D3SBA60 CML-700C AL T=2.0 TT2 BIN 3*8 MFZN PW(D0.7) FML-G22S KA278R05 CML-700C-1 AL T=2.0 TT2 BIN 3*8 MFZN PW(D0.7) FML-G22S KA278R33 FMB-G19L TLP721D4GR KA78R05 DLF-2323 1015#22(M)+SOLDER=180 CML-701C-1 A1050P-H24 H=21.5 TT2 BIN 3*8 MFZN PW(D0.7) SWRM PIE2.5X9 SN PLATE SSP7N60B DMT-700C TP8D13 CML-700CAV 25V RMU 1000MF (10*20) 16V RUS 470MF (10X12.5)TP 25V RUS 100MF (6.3X11) TP 16V RUS 1000MF (10X20) TP 16V RUS 470MF (10X12.
PART-DESC el. ne t CML-700CAV BI3857(AXIAL) UG2D 200V 2A 1N4148 AUTO 52MM UF4007 UG2D 200V 2A DZ22BM GDZJ 18C AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.65 TIN COATING AWG22 1/0.
PART-NAME 1/6 1K OHM J 1/6 1K OHM J 1/4 5.1K OHM J CML-700CAV YDH200-12+YBNH200-14+2990 9C=175(RGB) YDH200-08+YBNH200-09+1007#26=210 YH396-03V+35404-9002+1617#22=70 ST-03B-BP SEMKO TL 3.15AH 250V MF51 BSP3-H T0.4 SN 5.2 BSP3-H T0.4 SN 5.2 KA78R09 15P DDC BLUE W/OUT SCREW RS-309D-03 MD-104D-4P STEREO 3.5PIE GREEN “STEREO 3.5P, ST-029B-03BU” E.G.I. T=1.0 P.C T=0.5 (L700CAV) TT2 BIN 3X6 MFZN CML-701CTV MV 16V 22MF 5.0DX5.2H 50V Y5V 0.1MF Z 1608 50V X7R 2700PF K 1608 50V X7R 2700PF K 1608 MV 50V 2.2MF M 4.
PART-DESC el. ne t RLS4148 RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B RLZTE-11 5.6B PT2313L T=1.6*224*57 1/16 100 OHM J 1608 1/16 100 OHM J 1608 1/16 2.4K OHM J 1608 1/16 2.4K OHM J 1608 1/16 2.4K OHM J 1608 1/16 2.4K OHM J 1608 1/16 2.4K OHM J 1608 1/16 2.4K OHM J 1608 1/16 5.6K OHM J 1608 1/16 5.6K OHM J 1608 CML-700CAV CML-700C C/REAR AS TT2 BIN 3X12 MFZN BK L700CAV (DW) P.E T=0.
