AUTO WASHER WASHER AUTO WASHER AUTO WASHER WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER 2 2. STRUCTURE OF THE WASHING MACHINE 3 3. FUNCTIONS OF THE CONTROL PANEL 4 4. DIRECTIONS FOR INSTALLATION AND USE 5 5 6 5. WASHING PROCEDURE AND COURSE SELECTION FULL AUTOMATIC COURSE PARTIAL SELECTIONS AMONG WASH, RINSE OR SPIN DRY, SILK WAHING ENCHANCED CONVENIENCE IN USE 7 8 9, 10 11 6.
1. SPECIFICATIONS NO.
2. STRUCTURE OF THE WASHING MACHINE •HOT WATER TAP •COLD WATER TAP After using the washer, course the water tap and turn off the power After using the washer, close the water tap and turn off the power. •SOFTENER INLET Pour softener into the softener inlet just before wash and will be added into the tub automatically just before the final rinse.
3. FUNCTIONS OF THE CONTROL PANEL Control Panel It has micom sensor. As the buttons are pressed, the lamps indicating the selection of you desired washing program will light up. HOW TO USE SWITCH BUTTON FOR PROGRAM CANCEL • Press this Switch to turn the power ON or OFF . After turning OFF the power, wait for more than 3 seconds and then turn it ON again. • It can be used to cancel the fullautomatic course. • When the button is pressed the display will be light down.
. WASHING PROCEDURE AND COURSE SELECTION § è Full Automatic Course ¤Á Pressing the Power Switch ¤Ł Selecting Course Selecting Course Kinds of the Laundry FUZZY (SENSOR) This selection is for general MEMORY (USE ONLY FUZZY COURSE) This selection is washing course by washing. This selection is effective for some clothes made of silk. • Do not put in the wash marked with drycleaning. • 1Kg’s lb’s limitation for one-time-wash. ECONOMICAL COURSE START/HOLD START/HOLD Select your desired items.
§ è Partial Selections Among Wash, Rinse, or Spin ¤Á Pressing the Power Switch ¤ Ł Selecting Course Washing Procedure Procedure to Press the Button Only Wash WASH Only Rinse RINSE POWER START/HOLD Only Spin Wash & Rinse Wash & spin Rinse & Spin Wash ¤x Rinse ¤x Spin 8 PARTIAL SELECTION CANCEL Cancel the set program with pressing the button. *In case of canceling the program while the washer operates, press the “Start/Hold” button first, and then “Cancel” one.
§ è Dry Washing This selection is effective for high-quality sweater, underwear, wool, etc 1 Press the power switch 2 Press the course selection button to adjust to “Dry” 3 Put the special detergent into the tub, and press the Start/Hold button *After the height of water reachs the small level of water, the pulsator turns to solve detergent, and the water is continually supplied up to the mid level of water.
§ è Silk Washing This selection is effective for High-quality silk, stocking, silk curtain, etc 1 Press the power switch 2 Press the course selection button to adjust to “SILK” 3 Put the special detergent into the tub, and press the Start/Hold button *After the height of water reachs the small level of water, the pulsator turns to solve detergent, and the water is continually supplied up to the mid level of water.
6. FEATURE AND TECHNICAL EXPLANATION Feature of the Washing Machine 1 2 3 4 5 6 The first air bubble washing system in the world. Quiet washing through the innovational low-noise design. The wash effectiveness is much more enhanced because of the air bubble washing system. The laundry detergent dissolves well in water because of the air bubble washing system. The adoption of the water currents to adjust the unbalanced load. One-touch operation system.
Pulsator System When the pulsator is rotated C.W or C.C.W at a high speed, it makes the cyclone water flow from the asymmetrically designed pulsator as shown below. Asymmetrically designed pulsator makes the cyclone water fow, which get rid of the washing dead zone to increase the washing effect and reduce the entanglement of laundry. Automatic Drainning time Adjustment This system adjusts the draining time automatically according to the draining condition.
Softener Dispenser This is the device to dispense the softener automatically by centrifugal force. This is installed inside the auto-balancer. FUNCTIONAL PRINCIPLE 1 2 3 4 Softener stays in room (A) when poured into softener inlet. Softener moves from (A) to (B) by centrifugal force during intermittent spin process. Softener flows from (B) to (C) during rinse process next to intermittent spin. Softener moves from (C) to (D) by centrigfugal force during second intermittent spin.
Automatic Unbalance Adjustment This system is to prevent abnormal vibration during intermittent spin and spin process. FUNCTIONAL PRINCIPLE Always the safety switch contact is “ON” position. 2 In case that wash loads get uneven during spin, the outer tub hits the safety switch due to the serious vibration, and the spin process is interrupted. 3 In case that P.C.B. ASS’Y gets “OFF” signal from the safety switch, spin process are stopped and rinse process is started automatically by P.C.B. ASS’Y.
Lint Filter Much lint may be obtained according to the kind of clothes to be washed and some of the lint may also sticks to the clothes. To minimize this possibility a lint filter is provided on the upper part of the tub to filter the wash water as it is discharged from the water channel. It is good to use the lint filter during washing. Filter Filter Bleach Bleach Inlet Inlet Pulsator Pulsator HOW TO REPLACE LINT FILTER 1 Pull the filter frame upward.
Gear Mechanism Ass’y The proper water currents is made by the rotation of pulsator at a low speed (about 140 r.p.m) to prevent the damage to the small sized clothes. Pulsator shaft Spin shaft One way clutch bearing Gear unit as Sun gear Internal gear Planetary gear Clutch spring Brake lever Clutch boss Gear pulley Motor Pulsator 1490 r.p.m (50Hz) Gear unit as 1 revolution Motor Pulsator Gear Unit as Gear Pulley 140 r.p.m 1/5.2 5.2 revolutions 750 r.p.m Directly Gear pulley Tub 750 r.p.
PRINCIPLE OF INTAKE & OUTLET OF THE AIR INTAKE : ARMATURE moves up, and BELLOWS inhales the air. At the same time, protector B is open and A is close. OUTLET : ARMATURE moves down, and BELLOWS exhausts the air. At the same time, protector B is close and A is opend. FUNCTIONAL PRINCIPLE OF TRANS & MAGNET ¡ The phase of A.C electric power changes to 60 cycle/second. ¡ The magnetic pole of trans core is changed by the change of the phase of A.C electric power. ¡ The core repeats push and pull (3600 times/min.
7. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT Warning BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE WASHING MACHINE, DISCONNECT THE POWER CORD FROM THE ELECTRIC OUTLET. Gear Mechanism Ass’y Replacement ¡ Raise the top plate on the outer cabinet. ¡ Loosen four screws mounting outer tub cover and ¡ Loosen the pulsator mounting screw and remove the pulsator. remove outer tub cover from the tub ass’y.
Drain Motor and Valve ¡ Lay the front of the washer on the floor. ¡ Loosen the adjustment screw and four bolts mounting the drain motor. ¡ Take out the wire of drain motor from the bracket. Drain motor ¡ Separate the drain motor from the bracket. ¡ Turn the valve lid by using screw driver as shown in figure and remove the valve lid from the valve frame.
8. TROUBLE SHOOTING GUIDE NOTES 1. When replace the P.C.B. ASS’Y do not scratch the surface of the P.C.B. ASS’Y. 2. Disconnect the power cord from the electric outlet. Concerning Water Supply PROBLEM CHECK POINT CAUSE Do you open the water tap? NO SOLUTION Open the water tap. YES YES Is the filter of the water inlet valve clogged with dirt? Clean the filter. NO WATER IS NOT SUPPLIED. Increase the water pressure. NO Is the water pressure sufficient? (0.
PROBLEM CHECK POINT Does the water supply continue while the power is turned off? CAUSE SOLUTION YES The water inlet valve is defective. Change the water inlet valve. YES The triac of P.C.B is defective. Change the P.C.B ASS’Y. NO Does the water supply start as soon as you press the power switch? NO WATER SUPPLY IS NOT STOPPED.
Concerning Draining PROBLEM CHECK POINT Do you install the drain hose properly? CAUSE NO SOLUTION Improper installation Install the drain hose properly. Malfunction of drainage by the foreign matter Remove the foreign matter from the pump housing Drain pump is defective Change the Drain pump P.C.B ASS’Y is defective. Change the P.C.B ASS’Y. YES THE WASHER DOES NOT DRAIN.
Concerning Spinning PROBLEM CHECK POINT CAUSE SOLUTION YES Close the lid. Is the lid open? NO Does the door switch operate normally? Does the safety switch operate normally? NO Door switch is defective. Change the door switch. Safety switch is defective. Change the safety switch. Improper connection of the connector. Connect the connector properly. P.C.B. ASS’Y is defective. Change P.C.B ASS’Y. Drain motor is defective. Change the drain motor. P.C.B ASS’Y is defective. Change the P.C.
Concerning Operation PROBLEM CHECK POINT CAUSE SOLUTION NO Is the plug connect-ed to electric outlet? Connect the plug. YES YES Is Fuse opended? Change Fuse NO THE INDICATOR LAMPS(L.E.D) DO NOT LIGHT UP WHEN THE POWER BUTTON IS PRESSED. Is the condition of power button good? MOTOR ROTATES WHEN START/HOLD BUTTON IS NOT PRESSED. ABNORMAL NOISE DURING WASH PROCESS. Power button is defective Change P.C.B ASS’Y. Improper connection of the connector. Connect the connector properly.
9. PRESENTATION OF THE P.C.B ASS’Y Concerning Error Message MESSAGE CAUSE Improper installation of drain hose. Install drain hose properly. The drain hose is blocked up by foreign matter. Remove foreign matter from drain hose. Drain motor is inferior. Change drain motor. The water tap is closed. Open the water tap. The water inlet filter clogged. Clean the water inlet filter. It passes over the 30 minutes, yet it doesn’t come to assigned water level.
APPENDIX § è Wiring Diagram [Non-Pump] WIRING DIAGRAM 27
§ è [Non-Pump, Single Valve] 28 WIRING DIAGRAM
§ è [Pump] WIRING DIAGRAM 29
§ è [Pump, Single Valve] 30 WIRING DIAGRAM
§ è Parts Diagram A10 PARTS DIAGRAM 31
B24 B23 B15 B16 B17 B18 B22 B19 B21 B20 32 PARTS DIAGRAM
C32 PARTS DIAGRAM 33
§ è Parts List 1. DWF-7589, DWF-8089 NO PART CODE PARTS NAME EA A01 3611611400 DECORATOR PANEL F 1 PC FILM 0.188T A02 3614215900 PANEL F 1 ABS PRPSSWN500 A03 PRPSSWN800 P.C.
NO PART CODE PARTS NAME EA A26 3611521700 CUSHION DOOR 4 CR A27 3611405101 COVER L 1 ABS A28 7121401608 SCREW 8 T2S PAN 4x16 SUS 3612725100 A29 A30 A31 3612725110 DESCRIPTION LEFT NON-PUMP HARNESS ASS¡fl Y 1 PUMP 3612725120 NON-PUMP, SINGLE VALVE 3615403510 AC 110-130V/60Hz 3615403710 REMARK VALVE INLET COLD 1 AC 220-240V/50Hz 3615402010 AC 220V/60Hz 3615403630 AC 110-130V/60Hz 0EA;SINGLE VALVE AC 220-240V/50Hz 0EA;SINGLE VALVE AC 220V/60Hz 0EA;SINGLE VALVE 3615
NO PART CODE 3611200200 PARTS NAME EA CLAMP B 1 TERMINAL PUMP 1 3618703700 B18 3618703720 REMARK SW D2.6 ZN8-C PUMP 250V/1A PUMP 125V/3.
NO PART CODE C12 3611502800 C13 C14 PARTS NAME CUSHION DOWN EA 2 DESCRIPTION REMARK POM H=18mm 3964220400 AC 110V/60Hz F34-C 3964820510 AC 127V/60Hz F36-C AC 220/60Hz F3A-C 3964310510 AC 220V/50Hz F32-1C 3964610310 AC 240V/50Hz F33-1C 3610019700 3611502000 MOTOR CONDENSER 1 CUSHION UPPER 2 PULLEY MOTOR AS 1 3618401400 C15 3618401420 POM ADC-12, DS=10, DP=48.5 60Hz ADC-12, DS=10, DP=53.0 50Hz 3613218500 HOSE DRAIN AS 1 PE-LD/EVA, L=219.
2. DWF-9289, DWF-1089 NO PART CODE PARTS NAME EA A01 3611611400 DECORATOR PANEL F 1 PC FILM 0.188T A02 3614215300 PANEL F 1 ABS PRPSSWN500 A03 PRPSSWN800 P.C.
NO PART CODE PARTS NAME EA A26 3611521700 CUSHION DOOR 4 CR A27 3611406010 COVER L 1 ABS A28 7121401608 SCREW 8 T2S PAN 4x16 SUS 3612725100 A29 A30 A31 3612725110 DESCRIPTION HARNESS ASS¡fl Y 1 PUMP NON-PUMP, SINGLE VALVE 3615403510 AC 110-130V/60Hz VALVE INLET COLD 1 AC 220-240V/50Hz 3615402010 AC 220V/60Hz 3615403630 AC 110-130V/60Hz 0EA;SINGLE VALVE AC 220-240V/50Hz 0EA;SINGLE VALVE AC 220V/60Hz 0EA;SINGLE VALVE 3615403830 VALVE INLET HOT 1 3615402130 A32 71213
NO PART CODE PARTS NAME EA DESCRIPTION REMARK 4509M56000 HOSE DRAIN 1 L=930mm NON-PUMP 3613203101 HOSE AS 1 DWF-5230PN PUMP 3612502300 GUIDE DRAIN HOSE 1 PP PUMP 4501F06120 CLAMP 1 SWPA2 ZN8-C NON-PUMP 3611200200 CLAMP B 1 SW D2.6 ZN8-C PUMP 3618703700 TERMINAL PUMP 1 250V/1A PUMP 125V/3.
NO PART CODE PARTS NAME EA DESCRIPTION 3966320240 AC 220V/60Hz PUMP 3966010140 AC 220-240V/50Hz PUMP C09 4509M34010 BASE 1 SECEN 2.0Tx410x385 C10 4500D08180 CLAMP 1 SWC C11 4500D08170 HOSE 0.36 C12 3611502800 CUSHION DOWN C13 C14 REMARK 2 ID=8.0, OD=12.
