Washing Machine Instruction Manual DWD-E1211R'S/E1215R'S/E1211W'S/E1215W'S INSTRUCTION MANUAL Economic wash system Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water lever and washing time. Low noise system The washer minimizes the washing and spinning noises by sensing the amount of laundry. Child-Lock The Child-Lock system has been used to prevent children from pressing any button to change the program during operation.
PARTS AND FEATURES The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer. NOTE The drawings in the book may vary from your washer model. They are designed to show the different features of all models coverd by this book, Your model may not include all features.
WASHER SAFETY Save these instructions Your safety is important to us. To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic precautions. Read all instructions before using your washer Please ... • Have only a qualified person install, repair, or replace parts on washer. • Maintain washer properly. • Protect washer from the weather and keep it where the temperature will not fall below freezing.
INSTALLATION INSTRUCTIONS Removing transit bolts 1. Before operating the washer, remove the transit bolts(4ea) along with the rubber. 2. Unscrew the 4 bolts with the spanner supplied. Keep the 4 bolts and spanner for future use. • If the bolts are not removed, it may cause heavy vibration, noise and malfunction. • Whenever the appliance is transported, the transit bolts must be refitted. 3. Close the holes with the cap holders supplied.
INLET HOSE CONNECTION The washer should be connected to the water mains using new hose sets and old hose sets should not be reused. In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve. Option : Be careful not to confuse hot water inlet and cold water inlet. For Ordinary Tap 1 Pull down the collar of the inlet hose to separate it from the water tap adapter. 2 Loosen the four screws properly in order to fit into water tap.
ELECTRICAL REQUIREMENTS WARNING Electrical shock hazard : Failure to follow these instructions could result in death or serious injury. • Electrical earth is required on this washer • If it does not fit the outlet, have a proper outlet installed by a qualified electrician. • Don’t earth to a gas pipe. • Don’t change the power supply cord plug. • Check with a qualified electrician if you are not sure the washer is properly earthed.
2 Adjust the level of washer using adjustable legs. • Please check if there is any gap between the four adjustable legs and the floor. • Turning adjustable legs by the enclosed spanner, adjust the level of washer and make it sure that there is no swaying of washer. • After the adjustment is finished, turn the fixing nuts up tightly so that the washer maintains the adjustment.
Sorting • Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together. • Separate dark colors from light colors, colorfast items from non-colorfast item. Soil (Heavy, Normal, Light) Color (White, Lignts, Darks) Lint (Lint producers, Collectors) Separate clothes according to amount of soil. Separate white clothes from colored clothes. Wash lint producers and lint collectors separately. Loading • Drop items into washer loosely.
THE FUNCTION OF CONTROL PANEL(DWD-E12**R'S) Press this switch to turn the power 'ON' or 'OFF'. Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; Press the 'Start/Pause' button → Select the program that you want to change → Press the 'Start/Pause' button again. You can select the course you want and each lamp is turned on when that course is selected. You can select the wash course you want and each lamp is turned on when that course is selected.
THE FUNCTION OF CONTROL PANEL(DWD-E12**W'S) Press this switch to turn the power 'ON' or 'OFF'. Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; Press the 'Start/Pause' button → Select the program that you want to change → Press the 'Start/Pause' button again. You can select the course you want and each lamp is turned on when that course is selected. You can select the wash course you want and each lamp is turned on when that course is selected.
WASHING PROGRAM Program Fabric type Normal Colorfast garments (shirts, night dresses, pajamas,..) and lightly soiled white cottons(underwares,..) 40 °C (cold,30°C, 60°C) Wash: main wash Rinse: 3 Spin: 800 Temp.: 40°C Refer to rating lavel White First check whether laundry is machine washable. (white cotton, linen, towel and sheets..) 95 °C (fixed) Wash: main wash Rinse: 3 Spin: 800 Temp.: 95°C Refer to rating lavel Eco-White First check whether laundry is machine washable.
WASHING PROCEDURE AND SELECTION 1. NORMAL PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent.
2. WHITE PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button.
3. ECO-WHITE PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button.
4. SYNTHETIC PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button.
5. HEAVY STRAIN PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button.
6. WOOL PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) in the detergent case. • Softener should be below 'MAX' level. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the 'WOOL' program using the program selection dial.
7. DELICATE PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) in the detergent case. • Softener should be below 'MAX' level. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the 'DELICATE' program using the program selection dial.
8. BLANKET PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) in the detergent case. • Softener should be below 'MAX' level. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the 'BLANKET' program using the program selection dial.
9. RAPID PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) in the detergent case. • Softener should be below 'MAX' level. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the 'RAPID' program using the program selection dial.
10. MEMORY PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button.
11. DRUM CLEANING PROGRAM 1 Press the Power button. • The LED shows only '- --' signal. 2 Select the 'DRUM CLEANING' program using the program selection dial. • If you press 'Start/Pause' button aftrer pressing Power button without selecting program, the 'NORMAL' program is selected as default program. • 'Soak' and '2' times rinse and '400' rpm spin speed and 'Cold' water temperature (and 'Cupboard' dry condition) are selected automatically. 3 Press the 'Start/Pause' button.
GUIDE FOR OTHER USEFUL PROGRAMS * DELAY START(RESERVED WASHING) 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent.
* ONLY WASH 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the 'WASH COURSE' you want by pressing 'WASH' button. • The 'NORMAL' program is selected automatically. 4 Press the 'Start/Pause' button. • The washer will be operated with locking Door and supplying water.
* DRY(DWD-E12**R'S) 1 Put the laundry into the Drum and close the Door. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the 'DRY CONDITION' you want by pressing 'DRY' button. As this button is pressed, the dry condition is selected by 'Cupboard' → 'Very' → 'Time(30, 1:00, 1:30)' → OFF → 'Low Temp' → 'Iron' → 'Cupboard' 4 Press the 'Start/Pause' button. • The washer will be operated with locking Door. Note • Do not use the detergent and softener.
* RINSE+SPIN(DWD-E12**W'S) 1 Put the laundry into the Drum and put softerner into the detergent case. Then close the Door. • Softener should be below 'MAX' level. 2 Press the Power button. • The LED shows only '- --' signal. 3 Select the program you want using the program selection dial. • If you press 'RINSE+SPIN' button without selecting program, the 'NORMAL' program is selected as default program. 4 Press the 'RINSE+SPIN' button.
MAINTENANCE Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely. Cleaning your washer Exterior Interior Wipe up detergent, bleach, and other spills with a soft, damp cloth or sponge as they occur. Occasionally wipe the outside of the washer to keep its looking like new one. Clean interior with 250ml of chlorine bleach mixed with 500ml of detergent. Run washer through a complete cycle. Repeat this process if necessary.
HOW TO CLEAN THE FILTER Cleaning the water inlet filter • Clean the filter when water leaks from the water inlet. 1 Pull the power plug out before cleaning it. 2 Turn off the water supply to the washer and separate the inlet hose. 3 Pull the inlet filter out. 4 Remove the dirt from the inlet filter with a brush. Cleaning the drain filter • This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc..
REMOVING STAINS Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results. Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil before washing. Stain removal rules • Use warm water for soaking or prewashing stained laundry. Hot water can set stains. • Most stains are easier to remove when they are fresh.
TROUBLE SHOOTING Most problems are easily solved if you understand the cause. Check the following list for problem before calling for service. If the error mode such as IE, OE, UE were displayed on the control part, in order to solve these problem, first turn off the power of the washing machine and then turn on the power pressing Power button.
SPECIFICATION MODEL DWD-E1211R'S/E1215R'S DWD-E1211W'S/E1215W'S Dimension (mm) 630 x 750 x 930 (WxDxH) Unit Weight (kg) 80(Net) / 88(Gross) Maximum Mass of Dry Cloth Wash: 11Kg (Dry: 6.5Kg) Standard Water Consumption 130 l Spin Speed (RPM) No Spin/400/600/800/1000/1200 Operating Water Pressure 0.03MPa ~ 0.8MPa (0.
ABOUT THIS MANUAL VISION CREATIVE, INC. 서울 종로구 통의동 6번지 이룸빌딩4층 담 당 박양희님 TEL MODEL DWD-E1211R’ S, E1211W’S BUYER (아중동공용)DWD-E1211R'S/E1215R'S/E1211W'S/E1215W'S 일 정 제 판 규 격 1차 06.01.03 6차 2차 06.01.10 7차 3차 8차 4차 9차 5차 10차 06.01.11(Han)/06.02.23(Han) 인쇄 동일 MEMO 06.01.10-9,10_모델명 수정 06.01.11-전체출력 06.01.12-25,26수정후 재출력 06.02.23-30p_수정 06.02.23-전체출력 06.02.
