PARTS IDENTIFICATION •SPINDRYER LID •TUB O A TI T O R I N L IM T O A TI T O R I N L IM T •INNER LID •OVERFLOW FILTER •SPINDRYER DRUM •WASHER LID •GROUND WIRE (OPTION) •DRAIN STRAINER •POWER CORD •PULSATOR •BASE ACCESSORY LEG (4EA) DRAIN HOSE SAFETY COVER PUMP Control panel SH•RINSE WA ③ MIT N LI TIO 3 0MIN ④ OF F 15 TA 5 RO 0MIN ② RO ① TA MIT N LI TIO 1 DRAIN 12 WASH TIMER 4 6 9 VALVE SELECTOR ① Water Inlet Connect the hose from the water faucet to feed water to the tub
INSTALLATION ■ Location & Environment • Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation and cause an electric shock hazard. • Place washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface, noise or vibration may occur. (Allowable inclination is max. 2degrees) • Avoid direct sunlight or heating devices, as plastic and electrical components are affected by direct heat.
• Connection of Hoses • Attach the water intake hose to the water inlet located in the control panel. Fit the other end of the hose to either a hot or cold water tap as required. RO Caution: This unit is made of poly propylene, use water below 60 ° C ION LI MIT T AT WASH TIMER VALVE SELECTO R • Attach the drain hose to the drain outlet at the rear of the base. • Hang the drain hose on the edge of a sink.
HOW TO RINSE Overflow Rinse 1 Set the Valve selector to the “WASH · RINSE” position. 2 Turn the water tap on. 3 When the rinsing water becomes clear, turn off the water tap. 4 Set the Valve selector to the “DRAIN” position to discharge the water. Water Saving Rinse Note: Before rinsing, the wash load may be transferred to the spindryer drum for spinning for 2~3 minutes (approx.) to remove suds(See HOW TO SPIN DRY.) On completion, transfer the wash load to the wash tub for rinsing.
HOW TO SPIN DRYING 1 Put the wet clothes into the spindryer drum, being sure that they are well balanced as shown below. 2 Place the safety cover horizontally on the top. 3 Close the inner lid and spindryer lid. (The machine will not spin if the spindryer lid is open.) 4 Turn the spin timer in a clockwise direction until you reach the desired spin time position. Caution: Ensure that the spindryer drum completely stops before reaching in to remove the laundry.
CLEANING AND MAINTENANCE At the end of every washing: • Switch off the electricity of the power point. • Check that both timers are set to the “O” position. • Wipe off spillage (detergent powder,etc.), and generally wipe over the tub and base with a dry duster. * Cleaning after use will extend the life of your washing machine. Before cleaning disconnect the power cord from the electrical outlet. Overflow Filter • Remove the overflow Filter by pulling it forward.
POINTS TO REMEMBER • Avoid using excessive amounts of bleach, soap powder or detergent. Use the amount recommended by the respective manufacturers. • If the machine is installed in areas subject to freezing, ensure that it is completely drained after use. • When washing delicates e.g., silks, fine nylons, laces, etc., it is advisable to place them in a mesh bag to prevent the possibility of damage. • Do not wash lint attracting fabrics with lint producers, e.g.
= DW-5014 I N O TA T O R WASH L IM I T TIMER VALVE TAT IO RO SPIN TIMER WASHER-SPINDRYER INSTRUCTION MANUAL T ON TA I RO WASH LIM IT TIMER VALVE SELEC TOR RO SPIN • Thank you for selecting this washer-spindryer. • Before operating this unit, please read these instructions completely. • When you install this unit, be sure to assemble legs to BASE.
ABOUT THIS MANUAL VISION CREATIVE, INC. 중구 남대문로 5가 526 대우재단빌딩 16층 담 당 MODEL BUYER 일 정 제 판 규 격 MEMO 님 TEL (공장모델-DWM-4030MP) NW-4001(NEC) 1차 2000.10.23 6차 2차 2000.10.25 7차 3차 2000.10.31 8차 4차 2000.11.1 9차 5차 2000.11.6 10차 인쇄 한(2000.11.8) 2000.11.8 동일 (2000.11.14)-(1,3,4p)-3page 재수정 한(2000.11.17)-(1,3,4p)-3page 수정출력 2004.04.22-표지수정(Recycling mark추가) 2004.04.