S/M No.TCP850FEF0 Service Manual CHASSIS : CP-850/F MODEL : DTK-28 DTK-29 Caution : In this Manual, some parts can be changed for improving. their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List)in Service Information Center. JUN.
CP-850/F Service Manual CONTENTS 1 MAIN FEATURES 1.1 SPECIFICATIONS 1.1.1 GENERAL 1.2 CHANNEL/FREQUENCY TABLE 1.3 ATSS SORTING METHOD 1.3.1 GENERAL CASE 2 SAFETY INSTRUCTION 3 ALIGNMENT INSTRUCTIONS 3.1 MICROCONTROLLER CONFIGURATION : SERVICE MODE 3.2 SERVICE MODE NAVIGATION 3.3 MICROCONTROLLER CONFIGURATION : OPTION BITS 3.3.1 OPTION 1 3.3.2 OPTION 2 3.4 TV SET ALIGNMENT 3.4.1 LOCAL OSCILLATOR ALIGNMENT 3.4.2 G2 ALIGNMENT 3.4.3 WHITE BALANCE 3.4.4 FOCUS 3.4.5 VERTICAL GEOMETRY 3.4.
CP-850/F Service Manual 4.4.1.2 DSP-Section (Audio Baseband Processing) 4.4.1.3 Analogue Section 4.4.1.4 NICAM & FM/AM-Mono 4.4.1.5 German 2-Carrier System (DUAL FM System) 4.5 TDA4470 - MULTISTANDARD VIDEO-IF AND QUASI PARALLEL SOUND PROCESSOR 4.5.1 DESCRIPTION 4.5.2 FEATURES 4.5.3 PINNING 4.5.4 BLOCK DIAGRAM 4.6 TDA894XJ STEREO AUDIO AMPLIFIER 4.6.1 FEATURES 4.7 TDA835XJ VERTICAL AMPLIFIER 4.7.1 TDA8353J 4.8 TDA6108JF 4.9 24C16 - 16 KB EEPROM 4.10 STR - W6754 4.10.1 GENERAL DESCRIPTION 4.10.2 FEATURES 4.
CP-850/F Service Manual 5.3.1.7 RGB Front-End 5.3.1.8 Signal Processing 5.3.1.8.1 Horizontal Prescaler 5.3.1.8.2 Noise Reduction 5.3.1.8.3 Noise Measurement 5.3.1.8.4 Operation Modes 5.3.1.8.5 Digital 656 Output 5.3.2 BACK END 5.3.2.1 Digital Input Interface 5.3.2.2 Horizontal Scaler 5.3.2.3 Luma Contrast and Brightness 5.3.2.4 Black Level Expander/Compressor (BLEC) 5.3.2.5 Luma Sharpness Enhancer (LSE) 5.3.2.6 Dynamic Peaking 5.3.2.7 Luma Transient Improvement (LTI) 5.3.2.
CP-850/F Service Manual 5.8.
CP-850/F Service Manual 1 MAIN FEATURES 1.1 SPECIFICATIONS 1.1.1 GENERAL TV standard Colour system Tuner AV Sound system Power consumption Sound Output Power Speaker Teletext system Aerial input Channel coverage Tuning system Visual screen size Channel indication Program Selection Aux. terminal Remote Control PAL - SECAM B/G D/K, PAL I/I, SECAM L/L PAL, SECAM PAL, SECAM, PAL 60, NTSC M, NTSC 4.43 NICAM B/G, I, D/K, L, FM 2Carrier B/G, D/K 29"(4:3) Real Flat :110W approx.
CP-850/F Service Manual 1.2 CHANNEL/FREQUENCY TABLE 1.2.
CP-850/F Service Manual CHANNEL C01 C02 C03 C04 C05 C06 C07 C08 C09 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C57 C58 EUROPE CCIR 46.25 48.25 55.25 62.25 175.25 182.25 189.25 196.25 203.25 210.25 217.25 224.25 53.75 82.25 183.75 192.25 201.25 471.25 479.25 487.25 495.25 503.25 511.25 519.25 527.25 535.25 543.25 551.25 559.25 567.25 575.25 583.25 591.25 599.
CP-850/F Service Manual CHANNEL C59 C60 C61 C62 C63 C64 C65 C66 C67 C68 C69 C70 C71 C72 C73 C74 C75 C76 C77 S01 S02 S03 S04 S05 S06 S07 S08 S09 S10 S11 S12 S13 S14 S15 S16 EUROPE CCIR 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25 863.25 69.25 76.25 83.25 90.25 97.25 59.25 93.25 105.25 112.25 119.25 126.25 133.25 140.25 147.25 154.25 161.25 168.25 231.25 238.25 245.25 252.25 259.25 266.25 FRANCE 775.25 783.25 791.25 799.25 807.25 815.25 823.25 831.25 839.25 847.25 855.25 863.
CP-850/F Service Manual 1.3 ATSS SORTING METHOD The TV set sweeps all the TV bands from beginning of VHF to end of UHF. The TV controlling software for each program checks if a VPS CNI code is transmitted (this system exists for German, Swiss and Austrian transmissions). If no VPS CNI code is found, then the system checks if a CNI code is transmitted as part of the teletext transmission ( Packet 8/30 format 1 and format 2).
CP-850/F Service Manual Note : If two programs with the same name but a different code are found these two programs are listed in group I, II or III . The sorting order within group II, III, and IV is based on the channel frequency. The program with the lowest frequency is allocated the first rank in its group, and so forth until the last program of the group which has the highest frequency.
CP-850/F Service Manual 2 SAFETY INSTRUCTION WARNING: Only competent service personnel may carry out work involving the testing or repair of this equipment. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards, the high voltage must not exceed the specified limit. The nominal value of the high voltage of this receiver is 25-26 KV (20”-21”) or 26 KV (25” - 28”) at max beam current.
CP-850/F Service Manual 3 ALIGNMENT INSTRUCTIONS 3.1MICROCONTROLLER CONFIGURATION : SERVICE MODE To switch the TV set into service mode please see instruction below. 1 - Select PR. number 91 2 - Adjust sharpness to minimum and exit all menus. 3 - Within 2 seconds press the key sequence : RED - GREEN - menu The software version is displayed beside the word Service, e.g. “SERVICE V1.00”. To exit SERVICE menu press menu key or Stand By key. 3.
CP-850/F Service Manual 3.3.1 OPTION 1 3.3.2 OPTION 2 3.3.3 OPTION 3 Tube 4/3 - Real Flat, 16/9 – Real Flat Beam Current(mA) Nominal Max 1.30 1.45 1.35 1.50 B2 B1 B0 1 1 1 1 0 1 All values modified are immediately memorised in eeprom. 3.4 TV SET ALIGNMENT 3.4.1 LOCAL OSCILLATOR ALIGNMENT Tune a colour bar pattern. The frequency of the signal carrier must be accurate (Max +/- 10KHz deviation from the nominal channel frequency). Find AFT item in service mode.
CP-850/F Service Manual 3.4.3 WHITE BALANCE - Select a dark picture and adjust RED BIAS and GRN BIAS to the desired colour temperature. - Select a bright picture and adjust RED, GRN and BLUE GAIN to the desired colour temperature. 3.4.4 FOCUS Adjust the Focus volume ( on FBT ) to have the best resolution on screen. 3.4.5 VERTICAL GEOMETRY Adjust V. LINEAR (linearity), S CORRECT (S. Correction), VERT SIZE (Vertical amplitude), VERT CENT (vertical centring) to compensate for vertical distortion. 3.4.
CP-850/F Service Manual PARABOLA CORNER B & CORNER T EW TRAPEZ 3.4.8 AGC - Make sure option bits are correct for the tuner fitted on the chassis (See above how to change option bits). - Adjust the antenna signal level at 62 dB V± 2 - Tune a colour bar pattern. - Find the “AGC” item in service mode. - Press the key “OK” on the remote keypad and wait until AGC level stabilise to the optimum value. - Alternatively, use “Vol Up/Dwn” keys to adjust manually to the desired Tuner Take Over Point (TOP).
CP-850/F Service Manual 4 IC DESCRIPTION 4.1 TELETEXT DECODER WITH EMBEDDED 8-BIT CONTROLLER TVText Pro is a 8-bit controller based on a enhanced 8051 core with embedded teletext, On screen Display and TV controller functions. 4.1.1 BLOCK DIAGRAM OF THE SDA55XX 4.1.2 4.1.
CP-850/F Service Manual 4.1.3 IC MARKING AND VERSION Chassis CP-850/F IC marking OSD languages AUSTRALIA, BULGARIAN, CZECH, GERMAN, DANISH, SPANISH, FRENCH, FINNISH, GREEK, HUNGARIAN, ITALIAN, NORWEGIAN, DUTCH, POLISH, ROMANIAN, RUSSIAN, SWEDISH, ATSS countries Australia, Austria, Belgium, Switzerland, Czech Republic, Germany, Denmark, Spain, France, Finland, GB, Greece, Hungary, Italy, Ireland, Norway, Netherlands, Portugal, Poland, Sweden, Others Text PAN-EUROPEAN LATIN, CYRILLIC, GREEK. 4.1.
CP-850/F Service Manual PSDIP 52-pin 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Pin Name PROJECT50 n.c. n.c. n.c. VSS VDD3.3 n.c. n.c. RESET XTAL2 XTAL1 VSSA VDDA2.5 R OUT G OUT B OUT BK OUT VDD2.5 VSS VDD3.3 n.c. n.c. n.c. AGC FACTORY D/G COIL LED POWER Type Short Description IN IN Ground (0V) Input/Output 3.3V IN OUT IN IN IN OUT OUT OUT OUT IN IN IN A low level on this pin resets the device.
CP-850/F Service Manual VSP 94x5C 4.2.1 BLOCK DIAGRAM OF THE VSP9405C 4.2.
CP-850/F Service Manual Multi-standard colour decoder - PAL/NTSC/SECAM including all substandards - Automatic recognition of chroma standard - Only one crystal necessary for all standards RGB-FBL or YUV-H-V input - 8 bit amplitude resolution for RGB or YUV - 8 bit amplitude resolution for FBL or H ITU656 support - ITU656 output - DS656 output (double-scan ‘656like’ output) Noise reduction - Motion adaptive temporal noise reduction - Field-based temporal noise reduction for luminance and chrominance - Differ
CP-850/F Service Manual 4.2.3 PINNING Pin Connections and Short Descriptions for VSPB For VSP 941x/4x, the pin connections differ for pins: 1, 2, 3, 75, 76, 77, 78, 79, 80 (see Section 4.2.2. on page 210). Common Pin Connections and Short Descriptions Pin No.
CP-850/F Service Manual -22-
CP-850/F Service Manual -23-
CP-850/F Service Manual -24-
CP-850/F Service Manual -25-
CP-850/F Service Manual 4.3 DDP 3315C - DISPLAY AND DEFLECTION PROCESSOR The DDP 3315C is a mixed-signal single-chip digital display and deflection processor, designed for high-quality backend applications in double scan and HDTV TV sets with 4:3 or 16:9 picture tubes. The interfaces qualify the IC to be combined with state of the art digital scan rate converters, as well as analog HDTV sources.
CP-850/F Service Manual 4.3.2 DESCRIPTION Video Processing - linear horizontal scaling (0.25 ...
CP-850/F Service Manual IC architecture A clock generator converts different external line locked clock rates to a common internal sample rate of ~40 MHz, in order to provide a higher horizontal resolution. The input interface accepts ITU-R 601 at 27 or 32 MHz and ITU-R 656 with encoded or external sync at 54 MHz. The horizontal scaler is used for the scan rate conversion and for the nonlinear aspect ratio conversion as well. For the picture improvement, luma and chroma are processed separately.
CP-850/F Service Manual 4.3.3 PINNING Pin No.
CP-850/F Service Manual Pin No.
CP-850/F Service Manual 4.4 MSP341X MULTISTANDARD SOUND PROCESSOR The MSP 341x is designed as a single-chip Multistandard Sound Processor for applications in analogue and digital TV sets, video recorders, and PC cards. The MSP3411 has all functions of MSP3410 with the addition of a virtual surround sound features. Surround sound can be reproduced to a certain extent with two loudspeakers.
CP-850/F Service Manual 4.4.1.2 DSP-Section (Audio Baseband Processing) flexible selection of audio sources to be processed performance of terrestrial de-emphasise systems (FM, NICAM) digitally performed FM-identification decoding and de-matrixing digital baseband processing: volume, bass, treble simple controlling of volume, bass, treble 4.4.1.
CP-850/F Service Manual ADC Sound IF 2 Preprocessing Demodulator I2S1 I2S2 Source Select Sound IF 1 Prescale Loudspeaker Sound Processing DAC Headphone Sound Processing DAC Loudspeaker Subwoofer Headphone I2S SCART 1 SCART 2 SCART 3 SCART 4 DAC DSP SCART Input Select SCART1 Prescale ADC DAC MONO SCART2 Architecture of MSP341x Pin connections and short description Pin No.
CP-850/F Service Manual Pin No.
CP-850/F Service Manual 4.5 TDA4470 - MULTISTANDARD VIDEO-IF AND QUASI PARALLEL SOUND PROCESSOR 4.5.1 DESCRIPTION The TDA4470 is an integrated bipolar circuit for multi-standard video/sound IF (VIF/SIF) signal processing in TV/VCR and multimedia applications. The circuit processes all TV video IF signals with negative modulation (e.g., B/G standard), positive modulation (e.g., L standard) and the AM, FM/NICAM sound IF signals. 4.5.2 FEATURES - 5 V supply voltage; low power consumption.
CP-850/F Service Manual 4.5.4 BLOCK DIAGRAM Loop filter Offset comp. (optional) 26 18 l' switch VCO 20 21 VCO + phase shift FPLL 14 Control 19 AFC 6 VIF AFC switch 22 AFC VIF amp Video 7 CAGC Video det. 8 15 Standard switch 13 AGC (VIF) Standard CBL 23 11 Tuner 10 Take over point SIF 2 Tuner AGC Supply 17 Cref FM det. 27 24 28 SIF input switch V Intercarrier (FM/NICAM) SIF amp 3 1 SIF 1 2 25 AGC (SIF) 5 AM det.
CP-850/F Service Manual 4.6 TDA894XJ STEREO AUDIO AMPLIFIER The TDA 8944J ( TDA 8946J ) is a dual-channel audio power amplifier with an output power of 2 x 7 W ( 2 x 15 W ) at an 8 load and a 12 V supply. The circuit contains two Bridges Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8944J comes in a 17-pin DIL power package. 4.6.
CP-850/F Service Manual VCC1 3 VCC2 16 1 IN1IN1+ OUT1- 8 6 4 OUT1+ TDA8946J 17 IN2IN2+ OUT2- 9 12 14 OUT2+ VCC MODE SVR 10 STANDBY/ MUTE LOGIC SHORT CIRCUIT AND TEMPERATURE PROTECTION 11 2 15 GND1 GND2 MBK933 Block Diagram TDA8946J 4.7 TDA835XJ VERTICAL AMPLIFIER The TDA835xJ are power circuit for use in 90 and 110 colour deflection systems for field frequencies of 25 to 200Hz and 16/9 picture tubes.
CP-850/F Service Manual Vi(pos) 1 Vi(neg) 2 Vp 3 VcB 4 VEw 5 GNDv 6 GNDEw 7 VoEw 8 Vflb 9 VoA 10 TDA8358J Vo(guard) 11 VM 12 lcomp 13 V0(guard) Vp Vflb 13 11 3 9 comp guard Icomp M5 D2 M2 D3 D1 10 VoA +Vi(diff) Vi(sb) -Vi(diff) Vi(pos) 1 input/ feedback M4 12 VM Vi(neg) Vi(neg) 2 +Vi(diff) Vi(sb) -Vi(diff) M1 4 VoB M3 IiEW(top) IiEW(bot) M6 5 6 GNDV -39- 8 7 GNDEW VoEW
CP-850/F Service Manual 4.8 The TDA6108JF includes three video output amplifiers in one plastic DIL-bent-SIL 9-pin medium power(DBS9MPF) package(SOT111-1), using high-voltage DMOS technology, and is intended to drive the three cathodes of a colours CRT directly. To obtain maximum performance, the amplifier should be used with black-current control. Features Typical bandwidth of 9.
CP-850/F Service Manual Block diagram TDA6108JF 4.9 24C16 - 16 KB EEPROM Features : 16 Kbit serial I2C bus EEPROM Single supply voltage : 4.5 V to 5.5 V 1 Million Erase/Write cycles (minimum) 40 year data retention (minimum) Pin description Pin No. 1, 2, 3 5 6 7 8 4 Name E0, E1, E2 SDA SCL WC Vcc Vss Description Device address ? not used Serial Data/Address Input/Output Serial clock Write control Supply voltage Ground The memory device is compatible with the I2C memory standard.
CP-850/F Service Manual 4.10 STR - W6754 4.10.1 GENERAL DESCRIPTION The STR-W6754 is an hybrid IC with a build-in MOSFET and control IC, designed for flyback converter type switch mode power supply applications. 4.10.2 FEATURES - Rugged 650 V Avalanche-Rated MOSFET, Simplified Surge Absorption, No VDSS Derating Required - 0.
CP-850/F Service Manual 4.10.4 ELECTRICAL CHARACTERISTICS at TA = +25°C, VCC = 20 V, voltage measurements are referenced to S/GND terminal(unless otherwise specified).
CP-850/F Service Manual -44-
CP-850/F Service Manual 5 CP-850/F CHASSIS DESCRIPTION 5.
CP-850/F Service Manual 5.2 IF SECTION 5.2.
CP-850/F Service Manual 5.2.2 VISION IF AMPLIFIER The video IF signal (VIF) is fed through a SAW filter to the differential input (Pin 6-7) of the VIF amplifier. This amplifier consists of three AC-coupled amplifier stages. Each differential amplifier is gain controlled by the automatic gain control (VIF-AGC). The output signal of the VIF amplifier is applied to the FPLL carrier generation and the video demodulator. SAW filters Ref.
CP-850/F Service Manual 5.2.5 VIDEO DEMODULATION AND AMPLIFIER The video IF signal, which is applied from the gain controlled IF amplifier, is multiplied with the inphase component of the VCO signal. The video demodulator is designed for low distortion and large bandwidth. The demodulator output signal passes an integrated low pass filter for attenuation of the residual vision carrier and is fed to the video amplifier.
CP-850/F Service Manual 5.3.1.2 Input Selector The analog CVBS or SVHS luma signal are fed to the inputs CVBS1...7 of VSP94x2A (amplitude 0.5...1.5 V pp ). One signal is selected and fed to the first ADC. A second signal (SVHS Chroma) can be selected and fed to the other ADC. After clamping to the back porch both signals are AD-converted with an amplitude resolution of 9 bit. The AD conversion is done using a 20.25 MHz free-running stable crystal clock.
CP-850/F Service Manual 5.3.1.8.2 Noise Reduction The structure of the temporal motion adaptive noise reduction is the same for VSP 94x5C as for chrominance signal. The output of the motion detector is weighted. The look-up table input value range is separated into 8 segments. It is possible to freely program different behaviour of the noise reduction by using predefined curve characteristic for each segment. 5.3.1.8.3 Noise Measurement The noise measurement algorithm is used to sort program during ATSS.
CP-850/F Service Manual 5.3.2.5 Luma Sharpness Enhancer (LSE) Sharpness is one of the most critical features for optimum picture quality. This important processing is performed in the LSE circuitry of DDP 3315C. It consists of the dynamic peaking, the luma transient improvement (LTI) and an adaptive mixer. The luma input signal is processed in the peaking and LTI block in parallel. Both output signals are combined in the mixer depending on the selected LSE characteristic. 5.3.2.
CP-850/F Service Manual a) Cr Cb input of CTI b) Cr Cb input + correction signal c) sharpened and limited Cr Cb 5.3.2.10 Analog Back End The digital RGB signals are converted to analogue RGB by three 10-bit digital to analogue converters (DAC). Each RGB signal has two additional DACs with 9-bit resolution to adjust analogue brightness (40% of the full RGB range) and cutoff / black level (60% of the full RGB range). An additional fixed current is applied for the blanking level.
CP-850/F Service Manual The picture tube measurement returns results on every field for: - cutoff R - cutoff G - cutoff B - white drive R or G or B (sequentially) The average beam current limiter (BCL) works on both the digital YC r C b input from VSP and the inserted analog RGB signals (OSD and Teletext) by using the sense input for the beam current measurement. The BCL uses a different filter to average the beam current during the active picture resulting in a 12-bit resolution.
CP-850/F Service Manual 5.4.2 ACQUISITION FEATURES Multistandard Digital Data Slicer Parallel Multi-norm Slicing (TTX, VPS, WSS) Four Different Framing Codes Available Data Caption only Limited by available Memory Programmable VBI-buffer Full Channel Data Slicing Supported Fully Digital Signal Processing Noise Measurement and Controlled Noise Compensation Attenuation Measurement and Compensation Group Delay Measurement and Compensation Exact Decoding of Echo Disturbed Signals 5.4.
CP-850/F Service Manual 5.4.5 OVER CURRENT PROTECTION In case of overload, the SMPS secondary voltages will drop. The voltage on pin 18 of microcontroller drops below a reference voltage (x.xxV). The controlling software which continuously monitors this voltage will switch the set to stand by mode. To power on the set again the user must switch it off using the main power switch. Appropriate hysteresis guaranty a reliable operation. 5.
CP-850/F Service Manual or Swedish OSD languages are selected, the teletext will be correctly displayed. However, if Polish, Hungarian, Czech, Slovakian, Rumanian or Russian OSD are selected, the consequence will be incorrect teletext display for the national option characters. Romanian national font options will be selected.
CP-850/F Service Manual AM signals are derived from the amplitude information, whereas the phase information serves for FM and NICAM demodulation. 5.6.4 NICAM DECODER In case of NICAM - mode, the phase samples are decoded according the DQPSK - coding scheme. The output of this block contains the original NICAM bitstream. 5.6.5 DSP SECTION All audio baseband functions are performed by digital signal processing (DSP). The DSP section controls the source and output selection, and the signals processing. 5.6.
CP-850/F Service Manual Mute : In this mode the amplifier is DC biased but not operational (no audio output). This allows the input coupling capacitors to be charged to avoid pop-noise. The devices is in mute mode when 2.5 V < VMODE < (Vcc-1.5 V). Operating : In this mode the amplifier is operating normally. The operating mode is activated at VMODE < 0.5 V. 5.8 VERTICAL DEFLECTION The vertical driver circuit is a bridge configuration.
CP-850/F Service Manual 6. SERVICE PARTS LIST Caution:In this Service Manual, some parts can be changed for imroving, their performance without notice in the parts list. So, If you need the latest parts information, please refer to PPL(Parts Price List)in Service information Center(http://svc.dwe.co.kr) 6.
CP-850/F Service Manual LOC PART CODE R419 R444 R801 R803 R809 R819 R850 SF1 SF2 SW801 T401 T402 T801 U100 X501 Y801 Z153 ZZ200 CC01 CC02 CC03 CC04 CC05 CC06 CC07 CC08 CC10 CC100 CC110 CC111 CC115 CC117 CC119 CC120 CC129 CC13 CC14 CC15 CC16 CC160 CC17 CC18 CC19 CC20 CC21 CC30 CC31 CC32 CC501 CC502 CC503 CC504 CC505 CC506 CC507 CC508 CC509 CC511 CC512 CC513 CC514 CC515 CC516 CC517 CC518 CC521 CC522 CC523 CC524 CC526 CC527 RS01Y569JRS02Y100JS DTC7R0M270 RS02Y109JS RS02Y158JS RX10T339JRS02Y229JS 5PK3953M— 5
CP-850/F Service Manual LOC PART CODE RC610 RC661 RC662 RC666 RC701 RC702 RC712 RC713 RC715 RC720 RC721 RC722 RC723 RC724 RC729 RC730 RC731 RC732 RC733 RC734 RC737 RC738 RC739 RC740 RC741 RC742 RC743 RC750 RC751 RC770 RC790 RC799 RC801 RCA77 ZZ200 E01 E02 E03 E04 E05 E06 E07 E08 E09 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E21 E22 E23 E24 E25 E26 E30 E31 E32 E33 E40 E41 E42 E43 E44 E45 HRFT103JBA HRFT822JBA HRFT822JBA HRFT102JBA HRFT103JBA HRFT472JBA HRFT101JBA HRFT391JBA HRFT103JBA HRFT101JBA HRFT151
CP-850/F Service Manual LOC PART CODE C612 C613 C614 C615 C616 C623 C624 C625 C626 C630 C634 C636 C641 C642 C660 C661 C662 C668 C669 C690 C691 C709 C711 C713 C730 C733 C737 C742 C744 C803 C804 C806 C807 C808 C809 C810 C835 C845 C846 C860 C862 C863 C866 C876 C880 CA20 F801A F801B I704 I803 L101 L501 L802 Q103 Q104 Q110 Q150 Q151 Q333 Q334 Q402 Q501 Q502 Q542 Q543 Q544 Q550 Q601 Q603 Q604 Q605 CEXF1H109V CEXF1H109V CEXF1H109V CEXF1H109V CEXF1H100V CEXF1H109V CEXF1H109V CEXF1E101V CEXF1E101V CEXF1E470V CEXF
CP-850/F Service Manual LOC D801 D802 D803 D804 D805 D806 D807 D809 D812 D840 D850 D851 D861 D870 DA11 DA16 DA17 DA20 DA27 J047 J101 J102 J103 J106 J110 J112 J125 J128 J130 J135 J136 J142 J143 J145 J154 J155 J156 J159 J160 J201 J232 J234 J236 J240 J243 J276 J278 J287 J288 J289 J290 J291 J300 J301 J305 J306 J307 J308 J309 J310 J311 J312 J315 J320 J322 J324 J325 J327 J328 J329 J330 PART CODE PART NAME DESCRIPTION DLT2A05G— DLT2A05G— DLT2A05G— DLT2A05G— D1N4937G— D1N4937G— D1N4148—DTZX6V2—D1N4148—D1N4004S—
CP-850/F Service Manual LOC J423 J426 J427 J429 J430 J431 J432 J433 J434 J435 J440 J450 J460 J483 J501 J510 J601 J602 J603 J610 J701 J702 J703 J704 J707 J801 J810 J811 J812 J814 J815 J816 J817 J819 J820 J821 J822 J823 J824 J825 J889 L105 L153 L380 L381 L402 L502 L506 L507 L524 L551 L568 L601 L602 L603 L605 L650 L709 L711 L713 L730 L737 L742 L744 L801 LA01 LA02 LA03 PART CODE PART NAME DESCRIPTION 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060GY 85801060
CP-850/F Service Manual LOC R578 R579 R580 R588 R589 R590 R593 R594 R595 R599 R602 R603 R605 R606 R608 R609 R610 R613 R614 R615 R620 R621 R622 R641 R642 R646 R647 R649 R650 R651 R652 R660 R680 R700 R702 R703 R704 R708 R709 R710 R716 R720 R733 R741 R748 R781 R788 R789 R802 R805 R806 R807 R810 R811 R823 R826 R831 R832 R834 R841 R855 R860 R861 R862 R864 R865 R866 R867 PART CODE RD-AZ330JRD-AZ330JRD-AZ101JRD-AZ101JRD-AZ330JRD-AZ102JRD-AZ203JRD-AZ101JRD-AZ101JRD-AZ151JRD-AZ152JRD-AZ103JRD-AZ101JRD-AZ101JRD-2Z1
CP-850/F Service Manual 7.
CP-850/F Service Manual 8.
CP-850/F Service Manual PRINTED CIRCULT BOARD 68
CP-850/F Service Manual 9.
DAEWOO ELECTRONICS CORP. 686, AHYEON-DONG, MAPO-GU, SEOUL, KOREA. C.P.O. BOX 8003 SEOUL KOREA PRINTED DATE : JUN.
