PLASMA DISPLAY USER’S MANUAL DT-42A1 Proper use guarantees product life. Helpline Number : 0870 100 2525 Before using the product, be advised that you read this owner’s manual well and try to operate it.
Features • 42” VGA wide Plasma Panel • Built in 2-Analog Tuners This PDP has 2-analog tuners inside for watching terrestrial broadcasting without the need to purchase a separate broadcasting receiver. • Support Picture-in-Picture (PIP) • DVD Direct Connection / Outstanding Picture Quality via a Digital Broadcast Receiver DVD can be directly connected to the unit so that you can view clear digital images.
Safety Precautions Power Always obey all safety messages. During a lightning storm, or when it is left unattended and unused for a long period of time, unplug it from the wall outlet. It can result in fire. • All the safety and operating instructions should be read before the product is operated. If anything strange happens, unplug this product from the wall outlet. • Do not disassemble or replace any parts of the TV. Refer to a qualified service personnel for repair.
During Use The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not open the cover (or back) because high voltage is present within the TV enclosure. Never push any kind of objects into this product through openings at the back of TV. It may cause electric shock. It may cause fire or electric shock. Do not allow children to play or hang on the TV. Do not place a candle or lighted cigarette on the TV.
Safety Precautions Power Always obey all safety messages. When moving your TV, remove the power plug, antenna, and cables, and be sure to move it by using two people.. Do not touch the power plug with wet hands when plugging or unplugging it into the wall socket. It can result in a risk of electric shock. Failure to follow this instruction can result in electric shock or personal injury. • All the safety and operating instructions should be read before the product is operated.
During Use Do not wipe the TV using a cloth damped with chemicals (benzene, thinners, etc.). The TV appearance may be marred. (Unplug the power plug and wipe with soft cloth.) Do not place heavy objects or heat sources on the power cord. It may damage the power cord, causing fire or electric shock. The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit.
Checking Accessories Note Check to be sure that the following items are packed with your Plasma panel.
Note Optional Accessories The following items are optional accessories. Refer purchasing optional accessories from Daewoo Electronics Local Retailers or the retailer from where you purchased the unit.
CONTENTS PREPARATION 4 8 12 13 14 • • • • • Safety Precautions Checking Accessories Panel Controls Remote Control Remote Control Setup CONNECTION 15 18 20 26 28 30 32 34 36 38 40 • • • • • • • • • • • Antenna Connection To Watch TV Install Program Watching Digital Broadcasts Watching Cable Broadcasts Watching Satellite Broadcasts Watching a DVD Image Watching a VCR Image Watching a Camcorder/Game Console Image Connecting PC(15Pin D-Sub) Connecting PC(DVI) APPLICATION 44 45 47 50 51 53 54 57 58 59 61 6
Panel Controls Front Panel, Rear Panel * Items having the same names on the plasma display and the remote control would function in exactly the same way. Front / Side ON/OFF AV3 STAND-BY/OPERATE R-AUDIO-L VIDEO S-VIDEO INPUT SELECT MENU + VOLUME • Power button + MOVE / PR • Power Standby: Red - Standby Green - ON • Power control sensor 12 Pozycja obejm przeciwzakłóceniowych Select when adjusting volume or select/adjust “MENU.” Press when moving “MENU” or “Program”.
Rear AV1 DVI-D INPUT DVI-D INPUT PC INPUT (15 pin D-sub) COMPONENT A/V jacks (DTV/DVD INPUT jacks) AV2 SCART, A/V INPUT/OUTPUT, Cable Receiver INPUT/OUTPUT jacks ANT ANT Used when manufacturing (or manufacturer use only) Power 13
Note Remote Control * The number in ( ) indicates the page in which the function of each button is explained in detail. TV/VCR/DVD/SAT/CATV 19 Channel Number (0-9) Use to select channel directly (0-9). 58 RECALL Indicates the current state and resolution. TV Press to select TV Mode. COMPONENT, PC/DVI Press to select COMPONENT or PC/DVI modes. 20 Menu button Used to display a main menu. Previous Program button It returns to previous channel. Mute button Mute sound.
Remote Control Setup Remote Control supporting the multi brand devices. - The remote control provided is designed to operate the Daewoo PDP set. - However, using the remote control, you can control the Cable Converter, VCR , DVD and Satellite Broadcasting Receiver of other brands after setting up the remote control. Notices: - All the preset codes are erased when replacing the battery. In this case, you must set the remote control again.
Antenna Connection CTV Antenna Connection TV antenna installation may be found in most. When a coaxial cable is used Plug the coaxial cable to the antenna socket, and fix it firmly. Antenna socket on the wall Antenna socket at the back of the PDP unit. ANT/KABEL1 Coaxial cable When a feeder cable is used Antenna socket on the wall Antenna socket at the back of the PDP unit.
Outdoor Antenna Connection Outdoor antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses. Single Antenna Connection. VHF Antenna UHF Antenna ANT/KABEL 1 Separate Antenna Connection.
To Watch TV To Watch TV - The buttons on the keypad in the PDP unit, which have the same name as those on the remote control, perform the same function as the remote control. Press the “ON/OFF” button of the PDP unit. • The „ PR ” or power button of the remote control and the keypad on the PDP unit would be operated only when the „AC Power” of the PDP unit is supplied. Otherwise, neither the remote control nor keypad of the PDP unit can turn on the PDP.
Press the “ON/OFF” button. 1 • Press the “ON/OFF” button of the PDP unit. • The LED of the PDP unit turns red colour. • Press the “ PR ”, power button of the remote control, or any button on the keypad of the PDP unit. • The LED of the PDP unit turns “green” colour and the TV turns on. • To watch analog TV broadcasts, select the correct input, i.e. ‚PR’ in the on screen display box. 2 • Select the desired program by pressing the „ PR ” ,button or the number button.
Install Program Auto Setup - This is the function for the TV to memorize the broadcasting channels. If the Auto Setup is done, you can simply find programs with “ PR ” buttons and so need not select programs by pressing each program number. - Up to 100 TV stations can be stored in this set by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the “ PR ” button or Number buttons to scan the stations you programmed.
• Select the “Auto Setup” with the “ PR ” button. • Then press the “ VOL ” button. PR V O L V O L E PR V Edit Manual Setup Sound Screen SI ZE MENU Auto Setup Picture N 3 Select the “Auto Setup”. PR PR E RE SC Feature Install Move Exit Select the “Country”. PR V O L V O L E PR V SI ZE MENU • There are 18 countries for selection. Choose the desired country before starting the search. • If there is no proper country, select the “Others”.
Edit 1 Deleting the Program. • Place the selection bar on the program that you want to delete using the “ PR ” and “ VOL ” buttons. • Press the Delete(Yellow) button. • The deleted program goes to PR number 99 for recover. Edit PR PR98 PR99 PR0 PR1 PR2 PR3 PR4 Adjust Move 2 3 22 CH S41 S41 C69 S41 S41 S41 S41 Name ____ ____ ____ ____ ____ ____ ____ Delete Skip o o o o o o Exit Skip Moving the Program Positions • Place the selection bar on the program that you want to move.
Manual Setup 1 Press the Number Buttons(0~9) or the “ VOL ” Button to Select a Program Number You Want. Manual Setup Picture Sound Program 01 Channel C06 Fine Tune 48 Name Screen Feature ––––– Video PAL Audio D/K Search Memory Install Move 0~9 Adjust Exit Find the Desired Channel.
Manual Setup • Using ” VOL ” button, move the position where you want to write the character. • Select the desired character with the “PR” button. • There are A-Z, +, ., /, and 0-9 characters. • After naming, you can exit by pressing the ”Menu” button.
Find the Desired Channel with ‘Search’. 6 • By selecting the Search function, you can find the desired channel, but it searches only one channel unlike Auto Setup. • If the nearest channel is found, the searching would be stopped automatically. PR V O L V O L N E PR V SI ZE MENU PR PR E RE SC Manual Setup Picture Dźwiek Program 01 Channel C06 Fine Tune Name Screen Feature 48 C06 Video PAL Audio D/K Search Memory Install Move Exit Memorize the Program.
Watching Digital Broadcasts Watching Digital Broadcasts 1 Connect a Digital Broadcasting Receiver to the PDP • Prepare A/V cables. • Connect the cables from the digital TV Receiver output terminal to the PDP(Component 1, 2) input terminal. • When connecting the cables, be sure to match the cable colours. • To watch digital broadcasts: - Purchase a separate Digital Broadcasting Receiver(SET-TOP BOX) - Connect the PDP to a Digital Broadcasting Receiver as shown right.
CO M P 3 Input Select NT NE O • Select [Component 1 or Component 2] by pressing the “COMPONENT” button of the remote control or using the “INPUT SELECT” button of the PDP unit. • Each time you press the “COMPONENT” button, different input modes appear. The sequence is as follows: Component 1 Component 2 • N.B.: You cannot select component inputs if the picture in picture mode is on.
Watching Cable Broadcasts Watching Cable Broadcasts 1 Connect a Cable Broadcasting Receiver to the PDP. • Prepare the A/V cable. • Connect the receiver(Output) to PDP(Video Input) as shown below. • While using the scart cable for connection, put the ferrite core to the middle of the cable to prevent EMI (Electro Magnetic Interference). • To watch cable broadcasts, subscribe to your local cable TV broadcasting, and then connect a cable Broadcasting Receiver to the PDP as shown right.
3 Input Select AV • Select [AV 1(Scart), AV 2(Scart) or AV3(S-Video)] by pressing the [AV] button of the remote control or the “INPUT SELECT” in keypad of the PDP unit. • Each time you press the [AV] button, different input modes appear. The sequence is as follows: AV1 AV2 AV(S)3 • N.B.: An S-Video input into AV3 will take precedence over the normal yellow video lead so no need to utilise this if S-Video lead is used but you must still use the right and left audio leads to produce sound.
Watching Satellite Broadcasts Watching Satellite Broadcasts • To watch satellite broadcasting, subscribe to Digital Satellite Broadcasting, then connect the satellite Broadcasting Receiver to the PDP as shown right. 1 Connect a Satellite Broadcasting Receiver to the PDP. • Prepare the A/V cable. • Connect the receiver(Output) to PDP(Video Input) as shown below. • When connecting to an external AV source, be sure to match the colours.
3 Input Select AV • Select [AV 1(Scart), AV 2(Scart) or AV3(S-Video)] by pressing the [AV] button of the remote control or the “INPUT SELECT” in keypad of the PDP unit. • Each time you press the [AV] button, different input modes appear. The sequence is as follows: AV1 AV2 AV(S)3 4 Select the Desired Program and Function • Select the desired program and function by using the Remote Control of the Satellite Broadcasting Receiver.
Watching a DVD Image Watching a DVD Image 1 • Component Input is set to 480i/576i and 480p/576p mode. • Connect the cable from the DVD Video output (Y, Pb/Cb, Pr/Cr) to the Component Input at the back of PDP, and connect the cable from DVD audio output (Left, Right) to the Audio Input at the back of PDP. Connect a DVD Player to the PDP. • Prepare the AV cable. • Connect the DVD(Output) to the PDP(Component or Video Input) as shown below.
CO M P 3 Input Select T EN ON AV • Select [Component 1 or Component 2, AV1(Scart), AV2(Scart) or AV3(S-Video)] by pressing the [COMPONENT] or [AV] button of the remote control or the “INPUT SELECT” in keypad of the PDP unit. • Each time you press the [COMPONENT] or [AV] button, a different input mode appears.
Watching a VCR Image Watching a VCR Image 1 Connect a VCR to the PDP. • Prepare the AV cable. • Connect the Video(Output) to PDP(Video Input) as shown below. • If using the scart cable for connection, put the ferrite core to the middle of the cable for preventing EMI. • Video can use either the video terminal or the S-video terminal. VIDEO S-VIDEO AV3 AV2 R-AUDIO-L AV1 Video/Audio S-Video Video/Audio Ferrite Core VCR 2 34 Press the Power Buttons Turn the PDP and the VCR ON.
3 Input Select AV • Select [AV 1(Scart), AV 2(Scart) or AV 3(SVideo)] by pressing the [AV] button of the remote control or the “INPUT SELECT” in keypad of the PDP unit. • Each time you press the [AV] button, different input modes appear. The sequence is as follows: AV1 AV2 AV(S)3 4 Select the Desired Title and Function * Select the desired title and function by using the remote control of the VCR. NOTES: 1) When connecting a VCR the S-Video terminal provides a better image than the Video terminal.
Watching a Camcorder/Game Console Image Watching a Camcorder/Game Console Image • Enjoy images recorded by camcorder or the game console after connecting to the 1 Connect a Camcorder/Game Console to the PDP. • Prepare the AV cable. • Connect the Video(Output) to the PDP(Video Input) as shown below. • When connecting to an external AV source, be sure to match the colours. • If using the scart cable for connection, put the ferrite core to the middle of the cable for preventing EMI.
3 Input Select AV • Select [AV 1(Scart), AV 2(Scart) or AV 3] by pressing the [AV] button of the Remote Control or the “INPUT SELECT” in keypad of the PDP unit. • Each time you press the [AV] button, different input modes appear. The sequence is as follows: AV1 AV2 AV(S)3 4 Select Function • Select the function by using the remote control of camcorder or game console. NOTES: 1) When connecting the device, the S-Video terminal provides a better image than the Video terminal.
Connecting PC(15pin D-sub) Connecting PC • This product supports resolutions of VGA, SVGA, XGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of the PC. 1 Before Connecting to the PDP, Set the Resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen of the PC. • Choose the SETTINGS tab in the DISPLAY menu. • In the SETTINGS menu, select 640 x 480 or 800 x 600. 2 Connect the PC to the PDP. • Prepare the PC cable (D-sub 15pin) and the PC audio cable.
3 Press the Power Buttons. • Turn on the PDP and the PC. PC / I DV 4 Input Select • Select [PC] by pressing the [PC/DVI] button of the remote control or PDP unit. • Each time you press the [PC/DVI] button, a different input mode appears. The sequence is as follows: PC DVI • N.B. : You cannot select PC or DVI if the picture in picture mode is on. 5 Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or Mouse. NOTES: 1) The resolution of the PC monitor is the best at 640 x 480 (VGA).
Connecting PC(DVI) Connecting PC • This product supports resolution of VGA, SVGA, XGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of PC. • This product is supported by Plug and Play only at DVI. 1 Before Connecting to the PDP, Set the Resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen of the PC. • Choose the SETTINGS tab in the DISPLAY menu. • In the SETTINGS menu, select 640 x 480 or 800 x 600. 2 Connect the PC to the PDP.
3 Press the Power Buttons. • Turn on the PDP and the PC. PC / I DV 4 Input Select • Select [DVI] by pressing the [PC/DVI button of the remote control or the Input button on the PDP unit. • Each time you press the [PC/DVI] button, a different input mode appears. The sequence is as follows: PC DVI • N.B. : You cannot select PC or DVI if the picture in picture mode is on. 5 Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or Mouse.
PC and DVI Input Resolution Available in PDP • Depending on graphic card, problems like no signal detected or line noises can happen. If these problems happen, contact the graphic card company for help. Resolution H Freq. (KHz) V Freq. (Hz) Remark 640x400 37.861 85.080 VESA 640x480 31.469 59.940 DOS O O 37.861 72.809 VESA O O 37.500 75.000 VESA O O 43.269 85.061 VESA O O 31.469 70.087 IBM O O 37.927 85.039 VESA 35.156 56.250 VESA O O 37.879 60.317 VESA O O 48.
Selecting Picture Mode Selecting Picture Mode 1 • Select the Picture mode that is appropriate depending on the kinds of pictures, you enjoy. Selecting Picture Mode • Press the [PICTURE MODE] on the remote control. • While pressing the [PICTURE MODE] for the first time, the current picture mode will be displayed. 2 Each Press of the Button Will Select One of Four Picture Modes. • Each time you press the button, a different picture mode appears.
Customising Picture Press the MENU Button. 1 • The MENU shown below will display on the screen. Mode Picture Sound Normal Brightness 32 Contrast 48 Sharpness 32 Color Screen • You can adjust the colour tone and brightness to your preference. 32 Colour Temp. Feature Customising Picture Normal N.R. On CTI On Install Move 2 Exit Select Press the ▼PR▲ Button. • After selecting [Picture] by the “ PR ”, buttons, press the “VOL ” button. Then the sub menu of [Picture] will be displayed.
4 Select User Mode Adjustments • While you are in [Picture Mode – User], press the “ to select a specific adjustment item. Mode Picture Sound Screen Feature PR ” buttons User Brightness 32 Contrast 48 Sharpness 32 Color 32 Colour Temp. Normal N.R. On CTI On Install Move Exit Picture Condition Adjustments • Press the “ VOL ” buttons to adjust the picture of your preference. • N.R. and CTI function adjust the noise reduction and color resolution level of picture respectively.
Adjusting Screen 1 Press the SCREEN SIZE Button. • The current screen size will be displayed on the screen. • Each time you press the SCREEN SIZE button on the remote control, a different screen size appears. The sequence used is as follows in case of AV and TV modes : Auto 16:9 Adjusting with Screen Size button • You can adjust screen size or aspect ratio as desired. 4:3 LBS(14:9) Panorama LB(14:9) LB(16:9) 14:9 LBS(16:9) • N.B.
Adjusting Screen in the MENU Adjusting Screen 1 Press the MENU Button. • The MENU screen as shown below will appear. Mode Picture • You can adjust the screen in the menu. Sound Screen Feature Normal Brightness 32 Contrast 48 Sharpness 32 Color 32 Colour Temp. Normal N.R. On CTI On Install Move 2 Exit Select Press the “ ▼PR▲ ” Button. • Press the ” PR ” buttons to select ‘Screen’. Mode Picture Sound 16 : 9 H. Position. 32 V.
Adjusting Screen in the MENU PR V O L V O L E PR V Screen Mode Function ” Buttons. • Press the Volume “ VOL ” buttons to enter the sub menu “Screen”. • While you are in ‘Screen’ menu, press the ” PR” or “PR ” button to select a desired item, and then, adjust the value by pressing the “ VOL” or “VOL ” • This function is same to the [Screen Size] of remote controller. SI ZE MENU VOL N 3 Press the Volume “ PR PR E RE SC Mode Picture Sound 16 : 9 H. Position. 32 V.
Watching a STILL Image Watching a Still Image 1 Press the “STILL” Button. • If you wish to freeze a picture, press the “STILL” button. You can still hear the sound. • Press “STILL” button again to cancel the “STILL” function. • You can view still images with this function. However, displaying the same images such as still images for a long time may cause image burn. Still NOTES: 1) Displaying the same images such as still images for a long time may cause image burn (after-image lagging).
Watching Two Pictures Simultaneously • PIP (Picture-in-Picture) and P-by-P(Picture-by-Picture) modes allow users to watch two pictures simultaneously. POP mode is used in searching memorized 5 or 12 channels. 1 Engaging PIP mode • Press the ‘PIP’ button once on the remote control to engage the Picture-in-Picture mode. • By pressing the button repeatedly, it will show the following cycle. • If switched to P-by-P (Picture-by-Picture) mode, the screen will be split in half.
Watching Two Pictures Simultaneously 4 Select the program • Using program Up/Down buttons (PR /PR ), you may select the desired channels for sub-pictures. • The PR Up/Down buttons select the TV channels. 5 Select the Input Source • Various signal sources can be displayed within the sub-picture under PIP mode. • Once the PIP mode is on, you may change the input source of the sub-picture by pressing the ‘SOURCE’ button. • Pressing the ‚SOURCE’ button repeatedly will cycle through following order.
Adjusting Auto Sound Mode 1 Select “SOUND MODE”. 2 Normal • Enjoy various sound modes by selecting your favourite Sound Mode depending on the kinds of moving pictures. KEvery Press of the Button Changes Modes. • Each time you press the button, a different sound mode appears. The sequence used is as follows: Movie * Normal : * Movie : * Music : * News : * User : 3 Adjusting Auto Sound Mode • Press the “SOUND MODE” on the remote control.
Customising Sound Mode Customising Sound Mode Press the MENU Button. 1 • The MENU screen as below will be displayed. Mode Picture • This feature allows the user to adjust for their preference. Sound Screen Normal Brightness 32 Contrast 48 Sharpness 32 Color 32 Colour Temp. Feature Normal N.R. On CTI On Install Move Press the “ 2 PR Select Exit ” Button. • Select [Sound] by the “ PR ” buttons, then press the “VOL ” button to display the following.
4 Select the Effect Mode. • Select [Effect] by pressing the “ PR ” then select the desire sound effect by pressing the “VOL ” button. • [Effect]: Used to emphasize stereo effect. Balance Picture 0 Effect Off AVC Sound Normal 120Hz 0 500HZ 0 1.5kHz 0 5kHz 0 10kHz 0 Dual I Dual I sends the primary broadcast language to the loudspeakers.
Customising Sound Mode • Select the Sound Mode by pressing the “ PR ” buttons, then adjust it by pressing the “ VOL ” buttons. PR V O L V O L E PR V SI ZE MENU N 5 Select the Sound Mode. PR PR Balance Picture E RE SC 0 Effect Off AVC Sound Off Mode Normal 120Hz 0 500HZ 0 1.
Selecting INPUT SIGNAL 1 Press the Input Signal Selecting Button. TV VCR/DVD SAT CATV • Press the “TV”, “AV”, “COMPONENT” or “PC/DVI” button on the remote control or the PDP Display to select the desired input signal. • Each time you press input mode buttons, a different input mode appears. The sequence used is as follows: • “TV ” button INPUT SIGNAL • Used to select INPUT signal of external device connected to the PDP.
Checking the Current Input Signal - Press the [RECALL] button on the remote control, then displays basic informations of the current input signal, Under this state, pressing the [RECALL] button once more, additional informations about the current input signal will be displayed on the OSD. Checking the Current Input Signal Press the RECALL Button. 1 • Press the [RECALL] button on the Remote Control. Component 1 PM 12:00 • Used to check the INPUT signal mode, current time, resolution, channel, etc.
MENU Background, Language and Child Lock Setting Press the MENU Button. 1 • The MENU screen will be displayed as below. Mode Picture Sound Normal Brightness 32 Contrast 48 Sharpness 32 Color Screen • Used to select the tanslucent level of MENU background and language used in MENU. 32 Colour Temp. Feature Selecting Languages Normal N.R. On CTI On Install Move Press the “ 2 PR Exit Select ” Button. • Select [Features] by the “ PR ” button.
MENU Background, Language and Child Lock Setting 4 Select LANGUAGE by using the “ PR ”Button. • Select [Language] by using the” PR ” button. • Every press of the “VOL ” button while you are in the [Language] mode would cycle through the different languages.
MGDI (Meta Genuine Digital Image) MGDI is the image enhancement technology of Daewoo Electronics, which provides more clear, realistic, and delicate images. 1 Press the MENU Button. • The MENU screen will be displayed as below. Mode Picture Sound Normal Brightness 32 Contrast 48 Sharpness 32 Color Screen • MGDI function can not be used In PC and DVI modes. 32 Colour Temp. Feature MGDI Normal N.R.
Auto Power Setting POWER/STANDBY Indicator 1 Auto Power Setting • Select the [Auto Power] by pressing the “ PR ” button from [Features]. • You can select [Auto Power] ON and OFF mode by using the “VOL ” button. Front panel LED lights • When the AC power is on : Green. • When the AC power is in the standby mode : Red.
Time Setting 1 Press the MENU Button. • The MENU screen will be displayed as below. Mode Picture Sound Screen Normal Brightness 32 Contrast 48 Sharpness 32 Color 32 Colour Temp. Feature Normal N.R. On CTI On Install Move 2 Exit Select Select Features • Select [Features] by the “ PR ” button.
Time Setting Time Setting • The “Current time” must be set up ahead of setting up other time memories. 4 Off-Time and Wake time setting • Select Functions by pressing the “ PR ” button. First, set [Clock]- current time, and then You can setup off-time and wake time. • [Clock] : Adjust the desired hour and minute with “◄VOL►” button. • [Auto Clock] : Automatically setting the current time by teletext signal. • [Off Time] and [Wake Time] Setting methods are same as [Clock] setting method.
ISM (Image Sticking Minimisation) 1 Press the MENU Button. • The MENU screen will be displayed as below. Mode Picture Sound Screen Normal Brightness 32 Contrast 48 Sharpness 32 Color 32 Colour Temp. Feature ISM • Image Burn Minimisation • Displaying a still image for a long time causes part image sticking on the screen. • The ISM function minimises this effect. Normal N.R. On CTI On Install Move 2 Press the “ PR Exit Select ”Button. • Select [Features] by the “ PR ” button.
ISM (Image Sticking Minimisation) 4 Select Functions. • Every press of the “VOL ” button after select function by the “ PR ” button would switch between ON/OFF. ISM Picture Sound Pixel Shift On Low Bright. Off Img. Invert Off Screen Feature Install Move Adjust Exit NOTES: * Pixel Shift : The whole screen shifts up/down, left/right at 15 sec interval to minimize image sticking.
Initialize Setting 1 Press the MENU Button. • The MENU screen will be displayed as below. Mode Picture Sound Normal Brightness 32 Contrast 48 Sharpness 32 Color Screen • You can restore the values of the adjustment setting made in the MENU back to factory settings. 32 Colour Temp. Feature Back to Initialization Normal N.R. On CTI On Install Move 2 Exit Select Select Features • Select [Features] by the “ PR ” button.
Initialize Setting 3 INITIALISATION • Enter the sub Menu by using the “VOL ” button. • Select the [Initialize] by pressing the “ PR ” button, then press the “VOL ” button. • A confirmation message will be displayed. • To perform initialization, press the “VOL ” button after selecting [YES] by the “ PR ” button. • To return to MENU, press “MENU” button.
Setting Sleep Timer 1 Press the “SLEEP” Button. • Press the “SLEEP” button on the Remote Control. • Pressing the “SLEEP” button first time will display the current setting for Sleep Timer. • To cancel the Sleep Timer, press the “SLEEP” button to select ‘Off’. Setting Sleep Timer • Sleep Timer turns the PDP off after a preset time.
Teletext Switching Teletext ON/OFF • Press the Text button ( ). The index page or the page viewed last will appear. Press the Text button again to return to the TV mode. Colour buttons in TOP/FLOF Teletext • A red, green, yellow and cyan field is shown at the bottom of the screen. If TOP or FLOF Teletext is transmitted by the station, pressing the corresponding colour button on the remote control, you can select the desired page easily.
Calling Up Subpage Directly • Pressing the Subpage ( ) button. The subpage number is displayed at the bottom of the screen. To change the subpage, press the subpage number, for example, the 2nd page, sequence 02. The desired subpage will eventually be displayed on the screen and holds it there. Press this button again to exit this function. Watching television during teletext mode • Some pages are continually updated, for example, stock market reports, sports announcements, the latest news.
Before Requesting Service Checks Symptoms Before requesting for service, check the following points once again. • Remote control does not function properly. • The Display makes a snapping sound. • There are empty spots at the top and the bottom area of the screen. • Check for any obstacle between the Remote Control and the Display. • Check for dead batteries and incorrect battery orientation. • Check if the pictures and sound are normal.
SPECIFICATIONS DISPLAY UNIT Diagonal Size 106 cm (42”) Screen Aspect Ratio 16:9 System PAL B/G, I/I, SECAM B/G, D/K, L/L’ Display Resolution 852(H) x 480(V) dots Pixel Pitch 1,08(H) x 1,08(V) mm Dimension 1260(Sz.) x 653(W) x 91(Gł.) mm 49.61(Sz.) x 25.71 (W) x 3.50 (Gł) inch Weight 33 kg (72.75Lbs) Power Requirement 100-240V~, 50/60 Hz * Appearance and specifications of this product are subject to change for improving the product without prior notice.
