DSC-3210EGB D I G I T A L
ADDITIONAL INFORMATION FOR TV'S SOLD IN GREAT BRITAIN The appliance is supplied with a moulded three pin mains plug fitted with 5Amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 5 amp and approved by ASTA or BSI to BS1362. The plug contains a removable fuse cover that must be refitted when the fuse is replaced.In the event of the fuse cover being lost or damaged, the plug must not be used until a replacement cover has been obtained.
CONTENT REMOTE CONTROL & TV CONNECTIONS...............................................3 IMPORTANT SAFEGUARDS.......................................................................4 INSTALLATION............................................................................................4 START UP....................................................................................................5 CONNECTING EXTERNAL EQUIPMENT...................................................5 DAILY USE..................
REMOTE CONTROL & TV CONNECTIONS LOCAL CONTROL Front B2 B7 B1 B2 B3 B4 B5 Rear B8 B9 C3 C1 REMOTE sensor VIDEO INPUT socket AUDIO INPUT (L + R) socket PANEL S-VIDEO jack HEADPHONE socket C2 AV1 C1 C2 C3 B6 B10 B6 B7 B8 B9 B10 MAIN POWER button PROGRAM UP/DOWN buttons VOLUME UP/DOWN buttons TV / AV button STAND-BY indicator ANT B5 B4 S-VIDEO AUDIO VIDEO L Side B3 R B1 AV2 ANT IN SCART 1 socket SCART 2 socket AERIAL jack REMOTE CONTROL UNIT TV mode A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A
IMPO RT A N T SA FEG U A RD S WATER AND MOISTURE Never install the set in the following places: In a wet basement, bathroom. Do not place any container with liquid on the set. Do not expose the set to dripping or splashing water. HEAT Never place the set near heat sources. Never put a naked flame, such as a candle, on the top of TV set.
ST A RT U P LANGUAGE MENU The very first time that you turn on the TV, the LANGUAGE menu will appear on the screen. Its purpose is to enable you to select the language that will be used for all the OSD (On Screen Display) menus. The user must enter a choice of language before proceeding further. The language entered at this stage can still be modified at any later time, by entering the FEATURES menu (see later section under MENU DESCRIPTION).
DAILY USE SWITCHING ON TV SET 1) If stand-by indicator (B5) is red, then the TV set is in stand-by mode. You can switch on using the remote control POWER button (A1), the NUMBER 0….9 buttons (A3), or PROGRAM UP (A6) / DOWN (A21) buttons. The front panel PROGRAM UP/DOWN buttons (B2) can also be used. Once on, the stand-by indicator turns to green and the picture appears on the screen. 2) If stand-by indicator (B5) is not lit, then the TV set is powered off.
PICTURE CONTROL You can select three picture settings, by using the remote control NORMAL button (A17) : - Normal I (standard hard picture) - Normal II (standard soft picture) - Favourite For other adjustments: brightness, contrast, colour, sharpness, use the Picture menu. If an NTSC signal is received, then a tint adjustment will also be available.
MENUS DESCRIPTION MAIN MENU All menus are removed within 25 seconds if you don't press any button. Press the remote control MENU button (A19) to display the main menu. Then, you have the choice between several sub-menus: If you want to Exit the main menu, press the MENU button (A19) a second time. - To select one of the sub-menus, use the remote control CURSOR UP (A6), DOWN (A21) buttons. - To enter the selected sub-menu, press the remote control OK button (A18).
INSTALL MENU (For operating instructions, see " HOW TO USE THE SUB-MENUS ") INSTALL Automatic tuning system Program list edition TV system modification Channel number Channel Frequency Channel name Program number Program storage number ATSS GB TV system EDIT SYSTEM Channel number GB CHANNEL C47 FREQUENCY 679,25 NAME Country ABCDE Channel Frequency Channel name PROGRAM 00 Program number STORE TO 00 Program storage number Automatic Tuning System If you have a satellite decoder: If your
Manual Channel Tuning Choose a starting point Channel searching Enter station name - Select with "Program" the program from which you want to start manual tuning. Then the channel number, the frequency, the name and the program number of this program are displayed in the Install menu. - Select the "Frequency" function. - Press, and hold for more than 2 seconds, the remote control CURSOR RIGHT (A20) [LEFT (A7)] buttons to start up [down] manual tuning.
TELETEXT ENTERING/LEAVING TELETEXT MODE - Select the desired program with teletext. - Press the remote control TELETEXT button (A22) to select teletext mode. The initial page (or the last page viewed if you have already used teletext in the present channel) appears. - If you want to watch the TV program and use teletext at the same time, press the remote control teletext button (A22) again.
TELETEXT FORMAT PICTURE & SOUND CONTROL Doubling character height Repeatedly pressing the HEIGHT button (A23) doubles the character height in the following order : Upper half of the page (UP) > Lower half of the page (DOWN) > Return to normal height. Warning: In the TOP teletext menu (option), this control is inactive. In certain situations, the UP to DOWN (or DOWN to UP) change is automatic. For example, requesting a new page will force a change to UP.
