AKR-1010RC Cassette Player/Receiver with 4-Channel High Power Output Full Detachable Panel 4-Channel high Power(40W x 4Ch) Electronic Tuning Electronic Volume/Bass/Treble/Balance/ Fader 30Memory Capability (18FM+6MW+6LW) Local/DX Switch Loudness Mechanical cassette Player Detachable Face for Anti-Theft 10 CD-changer control INSTRUCTION MANUAL
WIRING CONNECTIONS The pins in the ISO connector have the following functions (connector seen from the rear) A. ELECTRIC CONNECTIONS 4. Back-up+12V : YELLOW 5. +12V (electric antenna) : BLUE 6. Dimmer : PINK 7. +12V supply(from ignition lock) : RED 8. Earth : BLACK B. LOUD SPEAKER 1. +Right Rear 2. - Right Rear 3. +Right Front 4. - Right Front 5. +Left Front 6. - Left Front 7. +Left Rear 8. - Left Rear : VIOLET : VIOLET/BLACK : GRAY : GRAY/BLACK : WHITE : WHITE/BLACK : GREEN : GREEN/BLACK C.
ASSEMBLY & REMOVAL OF THE APPARATUS NOTE ! Press knob(1) and remove front panel(2). (Always take the cassette out first). Insert the enclosed handles(3) into the cutouts in the apparatus, as in the figure, press the handles up somewhat so that the lock tabs release and pull the apparatus out of the holder. Remove the handles (3) from the apparatus. Only use the enclosed mounting components. Foreign components can upset operation.
FRONT PANEL Replacement of the front panel 1. Hold the panel at its top and bottom edges. 2. Press the left side of the panel in first. Then press the right-hand side in. Keep in mind: If any function does not work, take the panel off and put it back again. Do not touch the contact pins on the rear of the front panel, since this can cause contact problems. If the contacts should become dirty, they can be cleaned carefully with a soft rag. Do not expose the front panel to extremes of heat or cold.
FUNCTION DESCRIPTION, CONTROLS 3 4 13 12 11 10 15 2 1 17 16 9 8 18 7 14 19 1. POWER ON/OFF AUDIO SELECTOR 2. BASS / TREBLE / BALANCE / FADER / VOLUME 3. TUNING AND TRACK UP/DOWN 4. BAND CONTROL 5. LOUDNESS CONTROL/LOCAL STATION 6. AUT(AUTO TRAVEL PRESET)/INT 7. PRESET BUTTONS 8. DISPLAY CONTROL/PTY 9. AF/REGIONAL 10. TA/TP STANDBY 11. TAPE FAST FORWARD / REWIND 12. TAPE LOADING SLOT 13. TAPE EJECTION 14. CD-C 15. TOP 16. MTL 17. RANDOM 18. DISC +,19. LCD 20.
RADIO 1. POWER ON/OFF (POWER, 1) 3. TUNING UP/DOWN CONTROL ( To switch the audio system off, press power button lightly. Simultaneously, the system memorizes all information about its current setting, and restores the information when you turn the system on by pressing the power on/off button again. You can also turn the system on by pressing BAND or CDC button instead of power button. , 3) During the radio mode Press the tuning up/down arrows( ) for less than 0.
RADIO 5. LOUDNESS CONTROL (LOUD, 5) 8. DISPLAY CONTROL (DISP, 8) Press more than 1.5 sec. this button to select loudness or normal sound. The message “LD” appears on the display while you enjoy the BASS boost. To cancel, press this button again. When pressed belower than 1.5 seconds. present clock is displayed. another key is not pressed during 5 seconds, it is changed priority display states. LOCAL STATION (LOC, 5) When pressed LOC/LOUD button shortly, it displays the message “LOC”.
RADIO USING THE RDS FUNCTIONS What is RDS? RDS digital data includes various data : The RDS(Radio Data System) is a digital information system developed by the EBU(European Broadcasting Union). Pick-abacked on normal FM broadcasts, RDS offers a variety of information services and automatic retuning functions for RDScompatible car stereos. PI ... Program Identification Recognizes the country code and the program of the channel. PS ... program Service Name The name of the channel is shown in the display.
USING THE RDS FUNCTIONS 9. AF(network following) reception (AF, 9) This unit returns to the stronger alternative transmitter in the list of alternative frequencies(AF). The display indicates “AF” as confirmation on the display. Thus a motorist can keep listening to the same program. The AF-function is only possible with FM. To select AF-function switch to FM and press the button AF/REG for about 1.5 seconds.
USING THE RDS FUNCTIONS Change-over to regional program (REG, 9) 10. Traffic broadcast recognition (TA, 10) If the button “TA/TPST” is pressed for less than 1.5 seconds, RDS-stations transmitting traffic information can be heard. “TA” is displayed when this function is engaged. When the set is CD mode, the radio automatically tunes to a strong FM station transmitting traffic information in the back ground.
USING THE RDS FUNCTIONS Traffic information recognition (TP, 10) What is EON? EON(Enhanced Other Network) is a new RDS service provided by certain station networks. If the RDS-station tuned on, the unit recognizes RDS-frequencies with traffic information(TP). “TP” will be indicated on the display in reception of one of these frequencies. Even if you are tuned in to an RDS station which does not give traffic news, e.g.
USING THE RDS FUNCTIONS Program type recognition (PTY, 8) Radios equipped with PTY are able to display the various program features of an individual station. By selecting the PTY function you can get stations with the feature you want, i.e stations which broadcast mainly news bulletins, sports, pop music or rock music, for example. The radio will then only seek those with the features you have preselected. Selecting the PTY function Depress the button for approx. 2 seconds to tune on the PTYfunction.
CASSETTE PLAYER Listening to a tape 13. Tape ejection ( Insert a cassette tape. Playback will start automatically Press the “ , 13) ” button to remove your tape from the unit. During TAPE play time, it’s not changed the other mode (Radio, CDC) 14. MTL Function (MTL, 16) 11. Rewind / Fast Forward ( Switch the MTL function ON when the tape is a high position type like a metal tape, a chrome tape, etc. Set this button OFF for a nomal position type.
CD CHANGER OPERATION 15. TOP Function (TOP, 15) 17. Random Function (RDM, 17) At anytime you want to listen to the title song of disc press this button shortly. Then the CD will be played from the NO.1 track. If you want to enjoy the songs in a random order, press this button. Then “RDM” appears on the display with playing in a random order. Pressing the button once again the function returns to the normal play mode. 16. CD MODE SELECTOR (CDC, 14) Press CDC button to play CD.
TECHNICAL SPECIFICATION GENERAL Power supply Speaker impedance Output Power Current Drain TUNER SECTION Sensitivity Stereo separation Signal to Noise ratio Frequency Range Channel space TAPE SECTION 13.8V DC(10.8-15.6 allowable) 4 or 8 ohm Maximum 40W 4CH 10A FM MW 10dBu 30dB 55dB 87.
