AD100 OPERATING & APPLICATIONS MANUALS OPM100 The AD100 SECTION OPERATING MANUAL CHRYSLER/JEEP/PLYMOUTH CITROEN DAEWOO/CHEVROLET FIAT/ALFA/LANCIA FORD FORD USA/MERCURY/LINCOLN GENERAL MOTORS/VAUXHALL/OPEL HONDA/ACURA HYUNDAI JAGUAR KIA LAND ROVER MAZDA MITSUBISHI NISSAN/INFINITI PEUGEOT PROTON RENAULT ROVER SUBARU SUZUKI TOYOTA/LEXUS VW/AUDI/SEAT/SKODA Version 1.
1 OPERATING MANUAL
1 OPERATING MANUAL CONTENTS OPM100 PAGE PRECAUTIONS 4 INTRODUCTION 5 GENERAL OPERATION 6 FAULT CODE OPERATION 9 SPECIAL FUNCTIONS 11 ACTUATORS 12 SPECIFICATION 13
1 PRECAUTIONS 1. The AD100 is an electronic piece of equipment, and although designed for hostile environments it should not be exposed to excessive sunlight, high temperatures or immersed in liquids. 2. Return unit to carrying case when not in use. 3. Observe normal health and safety precautions when using this equipment. 4. When performing road tests, use a second person to operate the AD100. 5. Keep clear of all moving objects when near engine compartment. 6.
1 INTRODUCTION PRODUCT DESCRIPTION The AD100 is an Advanced Serial Diagnostic system which has been designed and developed to offer the most advanced diagnostic capabilities. The AD100 can be used as a hand held portable diagnostic system, and is equipped with 64MB of RAM which is used for the application data, and 4MB of Flash for the protocol handling system. In addition to this it has a RS232 interface connection for transferring application data from a PC and printing.
1 GENERAL OPERATION KEYPAD OPERATION Key is used for ENTER and CONTINUE operations FIG 1 Key is used for EXIT and BACKWARDS selection'stions. FIG 2 Key’ is used for UP and DOWN movement of selection. FIG 3 Number keys for entering codes and number selection.
1 GENERAL OPERATION PASSWORD OPERATION To stop unauthorised access the unit is fitted with a password system which is required to perform certain operations such as Immobiliser programming etc. Additionally the protection system is also used to protect unauthorised copying of update software. If there are any problems with password operation or with software updates, then the unit must be returned to Advanced Diagnostics.
1 GENERAL OPERATION INITIAL OPERATION After the correct cables and adaptor has been connected to the vehicle the AD100 will power up and the intial screen will be the contrast adjust. The screen will cycle between dark and light, and will stop as soon as a key is pressed. Use the UP and DOWN arrows to adjust the contrast, then press the ENTER key. FIG 7 The following sceen will be displayed.
1 FAULT CODE OPERATION READING FAULT CODES DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS Using the UP and DOWN keys select the FAULT CODES selection. Then press the ENTER key. SPECIAL FUNCTIONS DIAGNOSTIC MENU READ FAULT CODES CLEAR FAULT CODES Using the UP and DOWN keys select the READ FAULT CODES selection. Then press the ENTER key.
1 FAULT CODE OPERATION READING FAULT CODES (Contd) DISPLAY FAULT CODES NO FAULTS FOUND If there are no fault codes recorded, then the following screen will be displayed. PRESS ENTER KEY CLEARING FAULT CODES DIAGNOSTIC MENU Using the UP and DOWN keys select the CLEAR FAULT CODES selection. Then press the ENTER key.
1 SPECIAL FUNCTIONS LIVE DATA DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS From the DIAGNOSTIC MENU select the LIVE DATA function. PRESS ENTER KEY LIVE DATA IGN STAT PASS DOOR DRV DOOR RRH DOOR TP KEY1 PLIP 1 ON OPEN CLOSED OPEN PROG PROG Using the UP and DOWN arrows the additional LIVE DATA parameters will be displayed. LIVE DATA DOOR.CL.R DOOR.OP.R ENG ECU LO.SP.REL. HI.SP.REL DR.BUT.IP PASS.BUTT.
1 ACTUATORS ACTUATOR OPERATION DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS PRESS ENTER KEY Select ACTUATORS from the main menu. A list of actuators for the vehicle will be listed. Using the UP and DOWN arrows select the required actuator and press the ENTER key. ACTUATORS R.H.IND L.H.IND HAZ.W.LAM SCRN.WIP.SLOW SCRN.WIP.FAST BUZZER DE-ICING BUZZER ACTUATOR ON/OFF PLEASE CHECK OUTPUT The BUZZER as an example will sound for a short period of time and then stop.
1 SPECIFICATION DESCRIPTION OPERATING SUPPLY DISPLAY COMMUNICATION PORT REVERSE POLARITY PROTECTION SIZE SPECIFICATION 12 VOLTS DC 128 x 64 GRAPHIC DOT MATRIX LED BACKLIGHT CAN, J1850, ISO9141, SCP, 5 VOLTS, CCD PROTOCOLS YES 230 mm x 115 mm x 80 mm WEIGHT 400 gms MEMORY 512KB RAM 8MB FLASH 64KB ROM STORAGE TEMPERATURE OPERATING TEMPERATURE CURRENT CONSUMPTION SERIAL PORT 13 0°C to +50°C +5°C TO +40°C 200 mA RS232
2 CHRYSLER JEEP
2 CHRYSLER/JEEP MANUAL CONTENTS APM122 PAGE APPLICATIONS 16 GENERAL OPERATION 19 SPECIAL FUNCTIONS 21
2 APPLICATIONS VEHICLE TYPE KEYS ILCO JET STRATTEC YEAR SYSTEM CABLE CHRYLER /DODGE 300M Y160-PT Y160C-PHT 690222 1999-2000 TYPE 1 OR 2 ADC110 + ADC138 or ADC139 CHRYSLER /DODGE 300M Y160-PT Y160C-PHT 690222 2001-2003 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE BREEZE Y160-PT Y160C-PHT 690222 1999-2001 TYPE 1 OR 2 ADC110 + ADC138 or ADC139 CHRYSLER /DODGE CARAVAN Y160-PT Y160C-PHT 599455 2001-2003 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE CHEROKEE Y160-PT Y160C-PHT 690504 1999-2000 TYP
2 APPLICATIONS VEHICLE TYPE YEAR SYSTEM CABLE CHRYSLER /DODGE INTREPID 1998-2000 TYPE 1 OR 2 ADC110 + ADC138 or ADC139 CHRYSLER /DODGE INTREPID 2001-2003 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE LIBERTY 2002-2003 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE LHS 1999-2000 TYPE 1 OR 2 ADC110 + ADC138 or ADC139 CHRYSLER /DODGE LHS 2001 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE NEON 2000 TYPE 1 OR 2 ADC110 + ADC138 or ADC139 CHRYSLER /DODGE NEON 2001-2004 TYPE 2 ADC110 + ADC139 CHR
2 APPLICATIONS VEHICLE TYPE YEAR SYSTEM CABLE CHRYSLER /DODGE STRATUS 2DR HTP 2001-2003 STRATUS 2DR ADC110 + ADC138 HTP CHRYSLER /DODGE STRATUS 4DR HTP 2001-2003 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE TOWN & COUN- 2001-2003 TRY TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE VOYAGER 2001-2003 TYPE 2 ADC110 + ADC139 CHRYSLER /DODGE WRANGLER 1998-2000 TYPE 1 OR 2 ADC110 + ADC138 or ADC139 CHRYSLER /DODGE WRANGLER 2001-2004 TYPE 2 ADC110 + ADC139 CAN-BUS SYSTEMS VEHICLE TYPE YEAR SY
GENERAL OPERATION IMPORTANT NOTICE There are some models that may use 2 different systems in the same model year. In many cases it is not possible to tell which system the vehicle you are working on may use until you hook up your T-Code and try each system. You must switch adapters when trying a different System Type. If you try “Type 1” and the AD100 fails to communicate, then switch adapters and try “Type 2”. Remember to use the same adapter as the System “Type” you are selecting with the AD100.
GENERAL OPERATION KEY TYPES 20 2
SPECIAL FUNCTIONS Select CHRYSLER or DODGE from the Vehicle Selection Menu using the UP and DOWN arrows. Then press the ENTER key. Verify the System type from the model application guide. Make sure the transponder key is in the ignition and turned to the “ON” position. Press the ENTER button.
SPECIAL FUNCTIONS TYPE 1. TYPE 2. Select SPECIAL FUNCTIONS and press the ENTER button. “CLEAR KEYS” = Will erase all keys. “PROGRAM KEYS” = Add Keys to car. If you CLEAR keys - you will need to then program any keys you want to start the car, including the one in the ignition.
SPECIAL FUNCTIONS ERASING KEYS To erase all keys - Select CLEAR KEYS If you CLEAR keys - you will need to then program any keys you want to start the car, including the one in the ignition. Enter the 4 number PIN Code for the vehicle you are working on. The PIN Code is available from the dealer. You will need to confirm the PIN Code. (The PIN Code pictured is just an example) You will now need to program any keys you want to start the car, including the one in the ignition.
SPECIAL FUNCTIONS ADDING KEYS To Add keys - Select PROGRAM KEYS Make sure the transponder key is in the ignition and turned to the “ON” position. Press the Enter button. Enter the 4 number PIN Code for the vehicle you are working on. You will need to confirm the PIN Code. (The PIN Code pictured is just an example) You are done with the programming of the key in the ignition, press Enter to program more keys.
SPECIAL FUNCTIONS CARAVAN / PACIFICA / TOWN & COUNTRY—ERASE KEYS VEHICLE SELECTION CADILLAC CHRYSLER DODGE FORD GENERAL MOTORS ISUZU VEHICLE SELECTION IMMOBILISER REMOTE VEHICLE SELECTION IMPORTANT INFO ... 1. THE NON-REMOTE TRANSPONDER KEYS CAN BE PROGRAMMED AS A REPLACEMENT KEY. 2. ONLY NON-REMOTE TRANSPONDER KEYS WITH AN “S” STAMPED ON THE BLADE WILL WORK. THESE MODELS HAVE A NEW AND DIFFERENT TYPE OF TRANSPONDER CHIP. 3.
SPECIAL FUNCTIONS CARAVAN / PACIFICA / TOWN & COUNTRY—ERASE KEYS ECU IDENTIFICATION PACIFICA / CARAVAN DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS DIAGNOSTIC MENU CLEAR KEYS PROGRAM KEYS SECURITY CODE ____ SECURITY CODE 8247 IS CODE CORRECT OK=ENTER CLEAR=BACK 26 2
SPECIAL FUNCTIONS CARAVAN / PACIFICA / TOWN & COUNTRY—PROGRAM KEYS VEHICLE SELECTION CADILLAC CHRYSLER DODGE FORD GENERAL MOTORS ISUZU VEHICLE SELECTION IMMOBILISER REMOTE VEHICLE SELECTION SEBRING 2 DR HTP TYPE 1 TYPE 2 PACIFICA CHRYSLER CAN SWITCH IGNITION ON PRESS ENTER KEY 27 NOTE : ERASING ALL KEYS MEANS THAT ANY EXISTING KEYS MUST BE PROGRAMMED AGAIN.
2 SPECIAL FUNCTIONS CARAVAN / PACIFICA / TOWN & COUNTRY—PROGRAM KEYS ECU IDENTIFICATION PACIFICA / CARAVAN SECURITY CODE 8247 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS IS CODE CORRECT OK=ENTER CLEAR=BACK PROGRAMMING KEYS KEY PROGRAMMED ENTER—PROG.
SPECIAL FUNCTIONS CAN BUS SYSTEM (DURANGO)—PROGRAM KEYS/ERASE KEYS VEHICLE SELECTION CADILLAC CHRYSLER DODGE FORD GENERAL MOTORS ISUZU IMPORTANT INFO ... 1. THERE ARE NO NON-REMOTE CONTROL KEYS THAT CAN BE PROGRAMMED AT THIS TIME. 2. THE SAME REMOTE CONTROL HEAD IS USED ON ALL MODELS. VEHICLE SELECTION IMMOBILISER REMOTE VEHICLE SELECTION SEBRING 2 DR HTP TYPE 1 TYPE 2 PACIFICA CHRYSLER CAN SWITCH IGNITION ON PRESS ENTER KEY 29 3. A PIN CODE IS REQUIRED. 4.
SPECIAL FUNCTIONS CAN BUS SYSTEM (DURANGO)—PROGRAM KEYS/ERASE KEYS ECU IDENTIFICATION CHRYSLER CAN DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA SPECIAL FUNCTIONS DIAGNOSTIC MENU RE-PROGRAM KEYS PROGRAM NEW KEYS ERASE KEYS PROGRAM REMOTE SECURITY CODE ____ SECURITY CODE 8247 IS CODE CORRECT OK=ENTER CLEAR=BACK 30 2
SPECIAL FUNCTIONS CAN BUS SYSTEM (DURANGO)—PROGRAM KEYS/ERASE KEYS CHALLENGE CODE B6 37 8B 86 PIN CODE FOR VEHICLE TO BE OBTAINED FROM DEALER B6 37 8B AD RESPONSE CODE __ __ __ __ CHALLENGE CODE TO BE OBTAINED FROM ADVANCED DIAGNOSTICS. PRESS ENTER KEY RESPONSE CODE 82 47 55 6B IS CODE CORRECT OK=ENTER CLEAR=BACK PROGRAM KEYS PROCEDURE COMPLETE PRESS ENTER KEY 31 PROGRAM KEYS AND ERASE KEYS FOLLOW THE SAME PROCEDURE.
SPECIAL FUNCTIONS CAN BUS SYSTEM (DURANGO)—PROGRAM KEYS/ERASE KEYS WARNING FOLLOW NEXT SCREENS QUICKLY & CAREFULLY COMPLETE OPERATION WITHIN 60 Sec. AFTER HEARING THE CHIME After the PIN CODE and CHALLENGE RESPONSE CODES have been ENTERED, this screen should be displayed. Then 1. Sit in drivers seat, and make sure all doors are closed. 2. Put seat belt on, and make sure no PROGRAMMING REMOTES one else is in the vehicle. PRESS LOCK & UNLOCK 3.
2 SPECIAL FUNCTIONS CARAVAN—PACIFICA—TOWN&COUNTRY REMOTE KEYS 3 BUTTON REMOTE NO POWER SLIDING DOORS 4 BUTTON REMOTE PACIFICA 691718 STRATTEC DODGE LOGO S on BLADE 33 6 BUTTON REMOTE WITH POWER SLIDING DOORS 691729 STRATTEC CHRYSLER LOGO S on BLADE
2 SPECIAL FUNCTIONS CARAVAN—PACIFICA—TOWN&COUNTRY REMOTE KEYS MODELS YEARS CARAVAN (No Power Doors) 2004-2005 CARAVAN (with power Doors) 2004-2005 PACIFICA 2004 TOWN & COUNTRY (No power doors) 2004-2005 TOWN & COUNTRY (Power doors) 2004-2005 2004 DODGE DURANGO (CAN) FACTORY REMOTE—DEALER PART 34 DEALER REMOTE DEALER NON REMOTE
2 SPECIAL FUNCTIONS CHRYSLER REMOTE CONTROL SYSTEMS MODELS YEARS REMOTE SYSTEM TYPE AD100 ADAPTOR 300M 1999-2000 6 ADC138 2001-2004 6 ADC138 CIRRUS 1998-2000 10 ADC139 CONCORDE 1998-2000 6 ADC138 2001-2004 6 ADC138 1999-2000 6 ADC138 2001 6 ADC138 PT CRUISER 2001-2004 1 ADC138 SEBRING CONVERTIBLE 1998-2000 4 ADC139 2001-2004 6 ADC138 SEBRING 4 DOOR 2001-2004 6 ADC138 TOWN & COUNTRY 1998 9 ADC139 1999-2000 9 ADC139 2001-2003 3 ADC138 3 ADC138 LHS JEEP
2 SPECIAL FUNCTIONS DODGE REMOTE CONTROL SYSTEMS MODELS YEARS REMOTESYSTEM TYPE AD100 ADAPTOR CARAVAN 1998 9 ADC139 1999-2000 9 ADC139 2001-2003 3 ADC138 3 ADC138 1998 5 ADC139 1999-2000 5 ADC139 2001-2004 7 ADC138 1998 5 ADC139 1999-2000 5 ADC139 2001-2003 7 ADC138 1999-2000 6 ADC138 2001-2004 6 ADC138 NEON 2001-2004 1 ADC138 RAM PICK UP 1998 5 ADC139 1999-2001 5 ADC139 2002 5 ADC139 2002 8 ADC138 2003-2004 8 ADC138 1998-2000 10 ADC139 2001-20
2 SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 1 REMOTES 2001-2004 PT CRUISER 2000-2004 NEON DIAGNOSTIC MENU PROGRAM REMOTE TEST REMOTE PROGRAMMING REMOTES PRESS REMOTES BACK TO EXIT PROGRAMMING REMOTES PROCEDURE COMPLETE PRESS ENTER KEY 37 NOTES : A chime is heard as you enter and leave programming mode. A chime is heard when each remote is programmed. All remotes must be programmed at the same time.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 2 REMOTES 1999-2004 JEEP GRAND CHEROKEE DIAGNOSTIC MENU PROGRAM REMOTE NOTES : There are 4 memory positions for the TYPE 2 Remote System. 1,2,3 & 4 PROGRAM REMOTE PROGRAM REMOTE NO. X PROGRAM REMOTE PRESS & RELEAS.REMOTE PROGRAM REMOTE PROCEDURE COMPLETE Enter a number to fill a memory position for the remote you wish to program. This will overwrite the memory location if a remote is already stored there.
2 SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 3 REMOTES 2001-2003 CARAVAN 2001-2003 CARAVAN 2002-2004 JEEP LIBERTY DIAGNOSTIC MENU PROGRAM REMOTE PROGRAMMING REMOTES PRESS LOCK & UNLOCK TOGETHER FOR 1 Sec. WITHIN 3 Secs. PRESS EITHER KEY FOR 1 Sec REPEAT FOR ALL FOBS BACK TO EXIT PROGRAMMING REMOTES PROCEDURE COMPLETE PRESS ENTER KEY 39 NOTES : To program the remote press the LOCK and UNLOCK buttons together and then quickly press the UNLOCK button. A chime is heard as a remote is programmed.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 4 REMOTES 1998-2000 CHRYSLER SEBRING CONVERTIBLE DIAGNOSTIC MENU PROGRAM REMOTE NOTES : PROGRAM REMOTE DO YOU WANT TO ERASE REMOTES 1 = YES 2 = NO PROGRAM REMOTE HOLD LOCK BUTTON & DECKLID BUTTON TOGETHER FOR 10 Sec 40 Press the LOCK & DECKLID buttons together and hold until the door locks cycle to the unlocked position. This takes about 10 to 20 seconds. If the locks fail to cycle after 20 seconds, unplug your AD100 and start again.
2 SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 5 REMOTES 99-00 DODGE DURANGO 1998 DODGE DURANGO 99-00 DODGE DAKOTA 1998 DODGE DAKOTA 99-00 DODGE RAM PICK UP DIAGNOSTIC MENU PROGRAM REMOTE ERASE REMOTES PROGRAM REMOTE REMOTE 1 : 09A0A344 REMOTE 2 : FFFFFFFF REMOTE 3 : FFFFFFFF REMOTE 4 : FFFFFFFF PRESS ENTER KEY PROGRAM REMOTE PRESS REMOTE PRESS ENTER KEY NOTES : When you enter programming mode, a list of the current 4 remote memory positions will be displayed.
2 SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 6 REMOTES 1999-2004 1998-2004 1999-2001 2001-2004 2001-2004 DOOR 1999-2004 2001-2004 CHRYSLER CHRYSLER CHRYSLER CHRYSLER CHRYSLER 2001-2004 PT CRUISER DODGE INTREPID DODGE STRATUS 4 DOOR DIAGNOSTIC MENU PROGRAM REMOTE PROGRAMMING REMOTES PRESS LOCK & UNLOCK TOGETHER FOR 1 Sec. WITHIN 3 Secs.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 7 REMOTES 2001-2004 DODGE DAKOTA 2001-2003 DODGE DURANGO DIAGNOSTIC MENU NOTES : PROGRAM REMOTE There are 4 memory positions on the TYPE 7 system. 1,2,3 & 4 PROGRAM REMOTE ENTER REMOTE NO. X PROGRAM REMOTE PRESS & RELEAS.REMOTE AND THEN PRESS ENTER Enter the number to fill a memory position for the remote you would like to program. This will overwrite the memory location if a remote is already programmed into it.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 8 REMOTES 2002-2004 DODGE RAM PICK UP DIAGNOSTIC MENU PROGRAM REMOTE NOTES : Press the UNLOCK and LOCK buttons together and then quickly press the UNLOCK button. A chime is heard as you enter and leave programming mode. PROGRAMMING REMOTES PRESS LOCK & UNLOCK TOGETHER FOR 1 Sec. WITHIN 3 Secs. PRESS EITHER KEY FOR 1 Sec REPEAT FOR ALL FOBS BACK TO EXIT PROGRAMMING REMOTES PROCEDURE COMPLETE PRESS ENTER KEY 44 A chime is heard as a remote is programmed.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 9 REMOTES 1998 CHRYSLER TOWN & COUNTRY 1998 DODGE CARAVAN 1998 PLYMOUTH VOYAGER 1999-2000 CHRYSLER TOWN & COUNTRY 1999-2000 DODGE CARAVAN 1999-2000 PLYMOUTH VOYAGER DIAGNOSTIC MENU PROGRAM REMOTE NOTES : PROGRAM REMOTE Wait for chime—2 –3 seconds to start programming remotes. WARNING ALL REMOTES WILL BE ERASED PRESS ENTER KEY PROGRAMMING REMOTES PRESS LOCK & UNLOCK TOGETHER FOR 1 Sec. WITHIN 3 Secs.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 10 REMOTES 1998-2000 CHRYSLER CIRRUS 1998-2000 DODGE STRATUS (4dr) 1998-2000 PLYMOUTH BREEZE DIAGNOSTIC MENU NOTES : PROGRAM REMOTE To program remote :Press the LOCK and UNLOCK together for one second and then repeat again. PROGRAM REMOTE DO YOU WANT TO ERASE REMOTES 1 = YES 2 = NO PROGRAMMING REMOTES If you choose to erase remotes, you must go back and program any existing remotes. Do not erase again. A chime is heard when you enter programming.
SPECIAL FUNCTIONS REMOTE CONTROL PROGRAMMING TYPE 11 REMOTES 1998 JEEP CHEROKEE 1999-2001 JEEP CHEROKEE DIAGNOSTIC MENU PROGRAM REMOTE NOTES : There are 4 memory positions for the TYPE 11 remote system, 1,2,3 & 4 PROGRAM REMOTE ENTER REMOTE NO. X Enter the number to fill a memory position for the remote being programmed. PRESS UNLOCK BUTTON This will overwrite the memory location if a remote was already stored in it.
3 CITROEN
CITROEN MANUAL CONTENTS APM108 3 PAGE APPLICATIONS 50 GENERAL OPERATION 51 SPECIAL FUNCTIONS 52 TIPS & HINTS 56
APPLICATIONS 3 VEHICLE YEAR SYSTEM CABLE BERLINGO 1997 ON IMMO 1 ADC110 BERLINGO 1997 ON BSI ADC110 DISPATCH 1997 ON IMMO 1 ADC110 EVASION 1997 ON IMMO 1 ADC110 SAXO 1997 ON IMMO 1 ADC110 SYNERGIE 1997 ON CPH ADC110 XANTIA 1997 ON CPH ADC100 + ADC120 XSARA 1997 ON BSI ADC110 XSARA 1997 ON CPH ADC110 XSARA PICASSO 1997 ON BSI ADC110 C3 2002 ON BSI ADC110 C5 2002 ON BSI ADC110 C3 PLURIEL 2002 ON BSI ADC110 50
GENERAL OPERATION INTRODUCTION The Citroen Immobiliser systems are made up of 3 different types. They all perform various functions, and it is important to understand the basic configuration and the types of systems fitted. IMM– STANDARD IMMOBILISER This system was the first transponder system fitted to the Citroen range of vehicles, after the keypad system was phased out.
SPECIAL FUNCTIONS 3 PROGRAMMING KEYS—IMMOBILISER & CPH DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS PRESS ENTER KEY Select SPECIAL FUNCTIONS from the Diagnostic Menu using the UP and DOWN arrows. Then press the ENTER key.
SPECIAL FUNCTIONS PROGRAMMING KEYS—IMMOBILISER & CPH INCORRECT ACCESS CODE PRESS ENTER KEY SWITCH IGNITION ON IGNITION STATUS OFF SWITCH IGNITION OFF IGNITION STATUS ON 53 If incorrect code is entered the screen will display as shown. NOTE : If the code is entered 3 time incorrectly, then the ECU will lock access for 15 minutes. Follow on screen instruction for programming the keys. After switching IGNTION OFF remove the key and repeat procedure for additional keys.
SPECIAL FUNCTIONS 3 PROGRAMMING KEYS—BSi MODULE DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS PRESS ENTER KEY DIAGNOSTIC MENU PROGRAM KEYS Select SPECIAL FUNCTIONS from the Diagnostic Menu using the UP and DOWN arrows. Then press the ENTER key. NOTE : ENSURE ALL DOORS ARE CLOSED WHEN KEY PROGRAMMING IS BEING PERFORMED.
SPECIAL FUNCTIONS PROGRAMMING KEYS—BSi MODULE TRYING TO COMMUNICATE PRESS ENTER KEY SWITCH IGNITION OFF IGNITION STATUS ON If Access code is correct, ENTER the number of keys to program. NOTE : Max 4 keys can be added. Follow on screen instruction for programming the keys. PRESS ENTER KEY SWITCH IGNITION ON PRESS BACK TO EXIT PRESS ENTER TO PROGRAM NEXT KEY PRESS ENTER KEY 55 NOTE : AFTER PROGRAMMING CLEAR FAULT CODES AND LOCK VEHICLE FOR 10 MINUTES BEFORE TRYING THE KEY OR PLIP.
TIPS & HINTS 3 PEUGEOT & CITROEN VEHICLE KEY TYPE IDENT COLOUR PART NO SAXO STANDARD GREY 9926GY XSARA STANDARD BLACK GREY SERVICE KEY BLACK PLIP BLADE BLACK STANDARD KEY (MULTIPLEX) XSARA PICASSO STANDARD 9926FF 9926JZ 9926FG 9926LE 9926LE XANTIA STANDARD PLIP BLADE GREEN GREEN 9926HC 9926HA C5 STANDARD SYNERGIE STANDARD PLIP BLADE BLACK BLACK 9926FF 9926FG BERLINGO STANDARD STANDARD (MULTIPLEX) GREY 9926GY 9926LH DISPATCH STANDARD BLACK 9926FF RELAY STANDARD 9926LE 9926C
TIPS & HINTS SYSTEM IDENTIFICATION 106=CPH 206=Had BSI from the start but only had MUX from 51 Reg on (build code 9064 on) the design of the stalks gives it away, plip keys also different as it has a square appearance. 306=Never had MUX but late ones from approx V reg had HF plips and a CPH under the dash (passenger compartment protection unit) which worked locking and plips in one unit.
TIPS & HINTS BOXER EMERGENCY START This emergency procedure enables you to start the engine only if the engine doesn’t start because of an immobiliser problem. If the procedure is interrupted, you must do it again. That’s why it is important to read and understand properly the procedure before practising it. This procedure must be done for each starting. Procedure 1. Read the security code on the card 2. Switch off the ignition. Switch on the ignition 3.
TIPS & HINTS GENERAL Failure to program keys on CPH systems can be caused by corrosion to the large brown loom connector on the O/S inner wing or a melted pin in the large round connector situated on the n/s inner wing (below battery or air filter) Saxo on CPH systems have a very slow learn time, after successfully programming keys, remove the AD100, turn the ignition off and leave the vehicle alone for 30 mins.
4 DAEWOO
DAEWOO MANUAL CONTENTS APM118 PAGE APPLICATIONS 62 GENERAL OPERATION 63 SPECIAL FUNCTIONS 65 TIPS & HINTS 68 4
APPLICATIONS MODEL KALOS TACUMA LACETTI REMAN ESPERO PRINCE SUPER SALON CIELO PRINCE II BROUGHAM II LANOS NUBIRA NUBIRA 2000 MY LEGANZA 2000 MY LEGANZA MATIZ NUBIRA II MAGNUS LEZO ZETA YEAR ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS ALL MODELS CABLE ADC131(SWITCH ADC131(SWITCH ADC131(SWITCH ADC131(SWITCH ADC131(SWITCH ADC131(SWITCH ADC131(SWI
GENERAL OPERATION IMMOBILISER SYSTEM INTRODUCTION The immobiliser system provides theft protection using the ignition key and transponder device. An LED is used to indicate the immobiliser status. The immobiliser control unit communicates to the engine management unit when a valid key code is received and sends a security code to enable starting. If a valid key is used, the LED indicates the correct key status, if an incorrect key is used a fault code is set and the LED indicates an incorrect key status.
GENERAL OPERATION GENERAL OPERATION The remote control units lock and unlock the vehicle doors using radio frequency technology to the control unit. The range of control is 5-10 metres. When the doors are locked the indicator lamps flash once, and when unlocked the lamps flash twice. SECURITY INDICATOR The security indicator mounted in the instrument panel indicates the state of the security system. When the lock button is pressed, the control system is armed and the LED flashes.
SPECIAL FUNCTIONS KEY PROGRAMMING—ALL DAEWOO SYSTEMS (Except MATIZ) DIAGNOSTIC MENU ECU IDENTIFICATION SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS > KEY INFORMATION Select PROGRAM KEYS. PRESS ENTER KEY SWITCH IGNITION ON Switch IGNITION ON and press the ENTER key. AND THEN PRESS ENTER The key will be programmed.
SPECIAL FUNCTIONS KEY PROGRAMMING—(MATIZ) DIAGNOSTIC MENU > PROGRAM KEYS >SHOW KEY INFO NOTE : KEY PROGRAMMING ON MATIZ IS THE SAME AS THE OTHER DAEWOO VEHICLES, BUT OPERATION IS DONE MUCH SLOWER. PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS > KEY INFORMATION PRESS ENTER KEY On MATIZ information about the key in the IGNITION can also be displayed. From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. KEYCODE : A234029 A8500000 Select PROGRAM KEYS.
SPECIAL FUNCTIONS KEY PROGRAMMING—(MATIZ) PLEASE WAIT TRYING TO COMMUNICATE KEYCODE : A23429 PRESS ENTER KEY 67 After programming the key will be programmed.
TIPS & HINTS 4 When you have programmed keys, and the vehicle will not start even though the programming was successful, follow these instructions : The learn time for the engine control unit is very slow on this car. You will have to program the keys and then leave the vehicle alone for at least 30 minutes without the ignition OFF. If still no success, then disconnect the battery for 10 minutes and then test keys.
5 FIAT ALFA LANCIA
FIAT/ALFA/LANCIA MANUAL CONTENTS APM120 PAGE APPLICATIONS 71 SPECIAL FUNCTIONS 72 5
APPLICATIONS ALFA 5 VEHICLE YEAR SYS KEY PLIP KEY LIVE FAULT CABLE Y ADC110-B 147 ALL CAN Y Y Y 156 98MY ON ISO Y Y Y Y Y ADC110-B 166 98MY ON ISO Y Y Y Y Y ADC110-B LIVE DATA FAULT CODES CABLE Y Y ADC110-B Y ADC110-B FIAT VEHICLE YEAR SYS KEY PLIP PLIP PROG PROG INFO SCUDO ALL ISO Y Y DOBLO ALL ISO Y Y DUCATO 98MY ON ISO Y Y Y Y ADC110-B MULTIPLA 98MY ON ISO Y Y Y Y ADC110-B PALIO ALL ISO Y Y Y Y ADC110-B PUNTO NEW CAN Y Y Y
SPECIAL FUNCTIONS CAN SYSTEM 5 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main diagnostic menu select SPECIAL FUNCTIONS. SPECIAL FUNCTIONS PROGRAM KEYS KEY INFORMATION REMOTE INFORMATION ACTUATORS Select PROGRAM KEYS from the special functions menu. PRESS ENTER KEY PROGRAMMING KEYS KEYS NOT AVAILABLE WILL BE DELETED! NOTE : ANY KEYS NOT PROGRAMMED AT THIS POINT WILL BE DELETED PERMANENTLY.
SPECIAL FUNCTIONS CAN SYSTEM 5 PROGRAMMING KEYS REMOVE KEY INSERT NEXT KEY SWITCH IGNITION ON PRESS ENTER KEY REMOVE KEY from ignition then INSERT next key. Switch IGNITION ON. Press ENTER to continue. PROGRAMMING KEYS XX KEYS PROGRAMMED BACK TO EXIT ENTER TO PROGRAM REMOTES The number of keys now programmed in is displayed. To continue and program in REMOTES press ENTER. Otherwise press BACK to exit.
SPECIAL FUNCTIONS ISO SYSTEM 5 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main diagnostic menu select SPECIAL FUNCTIONS. SPECIAL FUNCTIONS PROGRAM KEYS LIVE DATA ACTUATORS KEY INFORMATION Select PROGRAM KEYS from the special functions menu. PRESS ENTER KEY SECURITY CODE _____ To enter the 5 digit security code use the following procedure :Press Press To elect Number & Letter To Erase the previous selection SECURITY CODE Press To ENTER selection.
SPECIAL FUNCTIONS ISO SYSTEM PROGRAMMING KEYS KEY ERROR 5 Depending on the status of the key inserted the following messages will appear: Press ENTER to continue. PRESS ENTER KEY OR PROGRAMMING KEYS KEYS PROGRAMMED: 1 BACK TO EXIT Press BACK to EXIT otherwise ENTER to continue.
SPECIAL FUNCTIONS ISO SYSTEM 5 KEY INFORMATION KEYS PROGRAMMED: 2 KEY 1: 12345678 KEY 2: 12345678 KEY 3: 12345678 KEY 4: 12345678 PRESS ENTER KEY ISO REMOTE PROGRAMMING PROGRAMMING REMOTES REMOTE INFORMATION REMOTES STORED : XX PRESS ENTER PROGRAMMING REMOTES PROGRAMMING REMOTE PRESS REMOTE AND HOLD FOR 3 SECS PROGRAMMING REMOTES PROGRAMMING REMOTE BACK TO EXIT ENTER TO PROGRAM NEXT REMOTE 76 The key information screen is displayed. Press ENTER to continue.
6 FORD
FORD MANUAL CONTENTS APM100 PAGE APPLICATIONS 80 GENERAL OPERATION 82 SPECIAL FUNCTIONS 86 TIPS & HINTS 95 6
APPLICATIONS VEHICLE TYPE KEYS YEAR SYSTEM CABLE KA PETROL 3 KEYS & 96/97 2 KEYS 97/98 97> PATS 2 PETROL ADC110 PATS 3 PETROL ADC110 ADC110 FIESTA/ COURIER PETROL 3 KEYS & 93 > 96 2 KEYS 96/97 97/98 98 > PATS 2 PETROL ADC111 PATS 3 PETROL ADC110 ADC110 ADC110 FIESTA/ COURIER DIESEL 3 KEYS & 95 > 97 2 KEYS 97 > PATS 2 PATS 3 ADC111 ADC110 PUMA PETROL 2 KEYS 1.7 ZETEC 1.
APPLICATIONS VEHICLE TYPE KEYS YEAR SYSTEM CABLE GALAXY PETROL > 97 97 > 00 00 > PATS 2 PATS 3 ADC110 GALAXY DIESEL > 97 97 > 00 00 > PATS 2 PATS 3 ADC110 WINDSTAR ALL > 97 97/98 98 > PATS 2 PATS 3 ADC110 EXPLORER ALL 97 > PATS 3 ADC110 TRANSIT PETROL 94 > 97 97 > 00 00 > PATS 2 PATS 3 ADC110 TRANSIT DIESEL 94/95 95/96 96/97 97 > 00 00 > TYPE 1 TYPE 2 PATS 2 PATS 3 ADC110 TRANSIT EPIC 95 > 97 97 > 97.5 97.
GENERAL OPERATION INTRODUCTION The FORD PATS systems were introduced on Ford vehicles on 94.5 M.Y. vehicles , and was available from March 1994. There have been many variations on the original system fitted. This system has a separate PATS Amplifier, however on subsequent systems the PATS module was incorporated into the Engine Management ECU. SYSTEM OPERATION The PATS system is a PASSIVE Anti-theft system which requires no special procedures for the driver to arm or disarm the system.
GENERAL OPERATION KEY OPERATION - 98¼ MY ONWARDS The newer systems are only supplied with 2 keys. Both keys are required to program further slave keys. Up to a maximum of 8 keys can be programmed to this PATS system. KEY PROGRAMMING - UP TO 98 ¼ MY NOTE : Clear ALL Fault codes before programming. A new master key can only be programmed using the FDS2000 or the AD100 systems. Further slaves can be added without any specialist equipment as follows :1. Insert master key, and turn to Position 2.
GENERAL OPERATION KEY PROGRAMMING - 98¼ MY ONWARDS NOTE : Clear ALL Fault codes before programming. Master keys can only be programmed using the 2 PATS keys (A and B) the FDS2000 or the AD100 system. NOTE : In some cases the vehicle doors must be closed to perform the re-programming sequence. Further slaves can be added without any specialist equipment as follows :1. Insert key A, and turn to Position 2. 2. Turn back to Position 0, and remove key A. 3. Insert key B, and turn to Position 2. 4.
GENERAL OPERATION PATS SYSTEM - PROBE ONLY The PATS system fitted to the Probe is unlike the other systems. The main difference is the system cannot be diagnosed with the FDS2000 or the AD100. Additional keys and re-programming of new keys are performed in a different procedure as well. PROGRAMMING NEW/ADDITIONAL KEYS (2 or more keys available) 1. Using one of the existing keys (This becomes KEY 1), insert into ignition switch.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (PETROL) DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS 6 Using the UP and DOWN keys select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU > CLEAR PATS 1 SYSTEM KEYS PROGRAMMED Using the UP and DOWN keys select the CLEAR PATS SYSTEM.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (PETROL) PROGRAM KEYS 3 KEYS REQUIRED PRESS ENTER KEY If successful the AD100 will display all keys cleared and how many keys are programmed. The key in the ignition is now programmed as the master key.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (DIESEL) DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS Using the UP and DOWN keys select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU > CLEAR PATS 2 SYSTEM KEYS PROGRAMMED Using the UP and DOWN keys select the CLEAR PATS SYSTEM.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (DIESEL) CLEAR PATS 2 SYSTEM ALL KEYS CLEARED KEYS PROGRAMMED : 1 PRESS ENTER KEY PROGRAM KEYS 3 KEYS REQUIRED PRESS ENTER KEY After Clearing the PATS module, the AD100 will automatically switch over to clearing the DSM (Diesel Smart Module) which takes 15 minutes. NOTE : If CONDITIONS INCORRECT are displayed then check the connection to the diesel pump, and clean the connections.
SPECIAL FUNCTIONS CLEARING PATS 3 SYSTEM (PETROL & DIESEL ENGINES) CLEAR PATS 3 SYSTEM MIN KEYS REQUIRED : 2 TIMED ACCESS CLEAR TIME 10:00 KEYS PROGRAMMED : 2 PRESS ENTER KEY CLEAR PATS 3 KEY GAINING ACCESS TIME ELAPSED 0:50 TIME REQUIRED 10:00 ACCESS STATUS IN PROGRESS BACK TO ABORT Follow the screen instructions to clear the PATS system. The AD100 will now start to clear the PATS system key codes from memory.
SPECIAL FUNCTIONS CLEARING PATS SYSTEM (FALCON) DIAGNOSTIC MENU NOTE : Minimum 2 keys required. > B.E.M. P.C.M. NOTE : Ensure all vehicle doors remain closed at all times. PRESS ENTER KEY FALCON B.E.M. PATS Connect AD100 to vehicle diagnostic connector, select Ford Falcon. Select BEM first and press ENTER. DO NOT TURN IGNITION ON when screen requests to. PRESS ENTER KEY DIAGNOSTIC MENU SPECIAL FUNCTIONS Press ENTER and continue. Select SPECIAL FUNCTIONS and press ENTER.
SPECIAL FUNCTIONS CLEARING PATS SYSTEM (FALCON) FALCON P.C.M. PATS PRESS ENTER KEY DIAGNOSTIC MENU Wait for door locks to cycle and then press ENTER key. Disconnect AD100 from vehicle. Wait 30 seconds after disconnecting AD100 Insert one of the keys into the ignition and turn IGNITION ON. SPECIAL FUNCTIONS Wait a further 30 seconds and the connect AD100 to vehicle again. PRESS ENTER KEY DIAGNOSTIC MENU CLEAR PATS 3 SYSTEM >PARAMETER RESET Continue to the same screen as previously but select P.C.M.
SPECIAL FUNCTIONS CHECKING KEYS PROGRAMMED DIAGNOSTIC MENU CLEAR PATS 1 SYSTEM > KEYS PROGRAMMED 6 Using the UP and DOWN keys select the KEYS PROGRAMMED. PRESS ENTER KEY KEYS PROGRAMMED 3 The number of keys stored in the Immobiliser ECU will be displayed.
SPECIAL FUNCTIONS ADD KEY FUNCTION DIAGNOSTIC MENU CLEAR PATS 1 SYSTEM KEYS PROGRAMMED > ADD KEY PRESS ENTER KEY CLEAR PATS 3 KEY GAINING ACCESS TIME ELAPSED 0:50 TIME REQUIRED 10:00 ACCESS STATUS IN PROGRESS BACK TO ABORT NOTE : On some vehicles a function is available to add a key without deleting the old keys. This takes the normal 10 minutes security access time. Using the UP and DOWN keys select the ADD KEY FUNCTION.
SPECIAL FUNCTIONS FORD CODED ACCESS UK ONLY PROCEDURE When connected to a coded access vehicle with AD100 and Special Functions selected, the following options will be displayed: CLEAR PATS ADD KEY (One code allows one key to be programmed.
TIPS & HINTS GENERAL If communication is made with the vehicle, and then no communication is experienced later or the communication is random, check battery voltage and ensure it is at least 12.2 volts. This is particularly important on the SCP vehicles, and all Transit models. A new function has been introduced on the WDS which enables the dealer to disable the additional key function. This is mainly used on fleet vehicles and hire companies to stop unauthorized key’s being added.
TIPS & HINTS Example Code : 31 6 A B C D The PATS system has it’s own self diagnosis test procedure which flashes codes.
1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 V/W W/X X/Y Y/A A/B B/C C/D D/E E/F F/G G/H H/J J/K K/L L/M M/N N/P P/R R/S S/T Y W V T S R P N M L K J H G F E D C B A YEAR C L J B C L J B C L J B C L J B C L J B JAN VIN EXAMPLE : WFY AXX GB GB PRODUCTION YEAR : 1992 PRODUCTION MONTH : MARCH YEAR REG LETTER N K Y U R K Y U R K Y U R K Y U R K Y U R
7 FORD USA LINCOLN MERCURY
FORD USA/LINCOLN/MERCURY MANUAL CONTENTS APM121 PAGE APPLICATIONS 100 SPECIAL FUNCTIONS 102 7
APPLICATIONS FORD VEHICLE YEARS SYSTEM CONTOUR V6 1997-98(a) PATS 1 CONTOUR V6 1999-00 PCM CROWN VICTORIA 1998-2002 PATS 2 CROWN VICTORIA 2003 PCM ESCAPE 2001-03 PCM EXCURSION 2000-03 PATS 2 EXPEDITION 1997-98 PATS 1 EXPEDITION 1999-02 HEC EXPEDITION 2003 PCM EXPLORER 1998-07-00 PATS 2 EXPLORER 07/00-2003 PCM FOCUS 2003 (PZEZ 2.
APPLICATIONS LINCOLN VEHICLE YEARS SYSTEM AVIATOR 2003 PCM BLACKWOOD 2002 HEC CONTINENTAL 1998-02 VIC LS 2000-02 ICM OR VIC LS 2003 ICM OR VIC MARK VIIII 1997-98 SCIL NAVIGATOR 1997-98 PATS 1 NAVIGATOR 1999-02 HEC NAVIGATOR 2003 PCM TOWN CAR 1998-02 HEC TOWN CAR 2003 PCM VEHICLE YEARS SYSTEM COUGAR 1999-2002 PCM MYSTIQUE (V6) 1997-98(a) PATS 1 MYSTIQUE (V6) 1999-2000 PCM GRAND MARQUIS 1998-2002 PATS 2 GRAND MARQUIS 2003 PCM MARAUDER 2003 PCM MOUNTAINE
SPECIAL FUNCTIONS CLEARING/PROGRAMMING VEHICLE SELECTION CADILLAC CHRYSLER DODGE FORD GENERAL MOTORS ISUZU Make sure the new key is in the ignition and turned to the ON position. Then Press the ENTER key. VEHICLE SELECTION PATS 1 PATS 2 PCM HEC VIC ICM Verify the system type from the model application guide. SWITCH IGNITION ON Key and Ignition should already be turned ON.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS ECU IDENTIFICATION = Displays the ECU iD FAULT CODES = To check and clear faults SPECIAL FUNCTIONS = Program Keys DIAGNOSTIC MENU >CLEAR PATS 3 KEYS PROGRAMMED ADD KEY Make your selection and press the ENTER key. CLEAR PATS 3 = To erase all keys KEYS PROGRAMMED = Check keys ADD KEY = To program additional key Make your selection and press Enter.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING MIN KEYS REQUIRED : 2 TIMED ACCESS CLEAR TIME 10:00 KEYS PROGRAMMED : 2 PRESS ENTER KEY CLEAR PATS 3 KEY GAINING ACCESS TIME REQUIRED : 10:00 TIME ELAPSED : 0:00 ACCESS STATUS IN PROGRESS BACK TO ABORT PROGRAM KEYS DISCONNECT TESTER FROM VEHICLE CYCLE KEYS TO PROGRAM DIAGNOSTIC MENU ECU IDENTIFICATION >FAULT CODES SPECIAL FUNCTIONS Programming keys : When adding a key you only need 1 key to cycle in the ignition after the 10 minute wait.
8 GM/OPEL GM HOLDEN VAUXHALL
GM, OPEL, GMHOLDEN,ISUZU MANUAL CONTENTS APPLICATIONS APM121 PAGE 106 GENERAL OPERATION 107 SPECIAL FUNCTIONS 111 TIPS & HINTS 117 7 8
APPLICATIONS OPEL/GENERAL MOTORS/VAUXHALL VEHICLE YEAR CABLE AGILA ALL MODELS ADC110 ASTRA - F 95 ADC113 ASTRA - F 96 ADC110/ADC110 ASTRA - G 98+ ADC110 CALIBRA 95 ADC113/ADC110 CALIBRA 96 ADC113/ADC110 CAVALIER 95 ADC113 CAVALIER 96 ADC113/ADC110 CORSA - B 95 ADC110 CORSA - B 96 ADC110 CORSA - C ALL MODELS ADC110 FRONTERA > 98 ADC110 FRONTERA 98+ ADC110 MONTERAY 96 ADC110 MONTERAY 97 ADC110 MONTERAY 98+ ADC110 OMEGA - B 94/95 ADC113 OMEGA - B 96+ ADC1
APPLICATIONS GM HOLDEN VEHICLE YEAR CABLE VR COMMODORE ALL MODELS ADC128 VS COMMODORE ALL MODELS ADC128 VT COMMODORE ALL MODELS ADC128 VX COMMODORE ALL MODELS ADC128 BARINA-B ALL MODELS ADC110 BARINA-C ALL MODELS ADC110 JACKAROO ALL MODELS ADC110 MONARO ALL MODELS ADC128 RODEO 2001 > ADC128 VU UTE ALL MODELS ADC128 WH STATESMAN ALL MODELS ADC128 WH CAPRICE ALL MODELS ADC128 YEAR ALL MODELS CABLE ADC110 ISUZU VEHICLE TROOPER 108 8
GENERAL OPERATION INTRODUCTION The General Motors Immobiliser is used in conjunction with the vehicle engine management electronics to immobilise the vehicle. The first systems were fitted to Petrol vehicles and subsequently fitted to Diesel vehicles from 95½ Model Year. The immobiliser system is independent, and can be diagnosed separately . The system is also operated independently from the central locking system, and it’s main function is to inhibit starting.
GENERAL OPERATION CAR PASS The information that is stored in the control unit includes Security Code, Engine type and transponder code. The security code cannot be erased or overwritten using the TECH 1, TECH 2 or the AD100. The security code consists of a 4-digit number and can be found on the car pass. If a new control unit is fitted, the new unit is not programmed with a code, and must be programmed using the TECH or AD100 units.
SPECIAL FUNCTIONS .CLEARING KEYS DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS PRESS ENTER KEY Select SPECIAL FUNCTIONS from the Diagnostic Menu using the UP and DOWN arrows. Then press the ENTER key. DIAGNOSTIC MENU > CLEAR KEYS PROGRAM KEYS PRESS ENTER KEY SWITCH IGNITION OFF IGNITION STATUS ON Using the UP and DOWN keys select the CLEAR KEYS option Please follow the instructions on the screen.
SPECIAL FUNCTIONS .CLEARING KEYS ERASING KEYS KEYS ERASED PRESS ENTER KEY If the code is correct, the AD100 will display ACCESS GAINED. It will then automatically erase all the keys and display the message KEYS ERASED if successful. PROGRAMMING KEYS DIAGNOSTIC MENU CLEAR KEYS > PROGRAM KEYS Using the UP and DOWN keys select the PROGRAM KEYS option PRESS ENTER KEY KEYS PROGRAMMED 0 If the clearing key function was successful the AD100 should indicate that there are no keys programmed.
SPECIAL FUNCTIONS SECURITY CODE 1234 IS THIS CORRECT OK = ENTER CLEAR =BACK ACCESS GAINED If code is correct press the ENTER key. If code is entered incorrectly then press the BACK key to reset the code. If the code is correct, the AD100 will display ACCESS GAINED. Follow the screen instructions.
SPECIAL FUNCTIONS DIAGNOSTIC MENU CLEAR PLIPS SWITCH IGNITION ON 8 PRESS ENTER KEY DIAGNOSTIC MENU ERASING PLIP PROCEDURE COMPLETE PRESS ENTER KEY PROGRAMMING PLIPS CLEAR PLIPS > PROGRAM PLIP After selecting PLIP functions select SPECIAL FUNCTIONS and follow on screen instructions. PRESS ENTER KEY SWITCH IGNITION ON After selection, new PLIP key should be pressed until screen indicates PLIP is programmed.
SPECIAL FUNCTIONS PLIP PROGRAMMED PRESS ENTER KEY PLIP KEY SYSTEMS TYPE 1. Teardrop shaped plip, separate from key. First System. TYPE 2. Type used on early systems, with integrated remote key head. TYPE 3. Type used on AstraG vehicles. TYPE 4. Type used on VectraB vehicles, and requires PIN CODE] TYPE 5.(ATW) Type with Alarm system fitted (V6 etc) TYPE 6 Type used on Astra & Zafira with ATW and Ultrasonics mounted on the B-post.
SPECIAL FUNCTIONS PIN CODE READING CLEAR KEYS PROGRAM KEYS READ PINCODE PRESS ENTER KEY Select the READ PIN CODE option for the Special Functions menu. Before reading the pin code the Immobiliser ECU requires resetting. The procedure for this is to disconnect the connector from the immobiliser and then re-connect. Remove the plastic cover from the underneath of the steering wheel column. Disconnect the connector and then reconnect.
TIPS & HINTS GENERAL MOTORS 1. Check the vehicle battery, to ensure the voltage is at least 12 volts. 2. V registration Vectra, use ASTRA-G 98 vehicle selection. 8 CONNECTOR’S On some Calibra’s the 10 Pin connector mounted in the R/H engine bulkhead is prone to water ingress, and can cause bad connections. In some cases there was nothing that could be done, until the connector had been replaced.
9 HONDA ACURA
HONDA / ACURA MANUAL CONTENTS APM119 PAGE APPLICATIONS 120 GENERAL OPERATION 122 SPECIAL FUNCTIONS 126 TIPS & HINTS 133 7 9
APPLICATIONS HONDA VEHICLE YEAR SYSTEM CABLE CIVIC/ACCORD * 1 >99 TYPE 5 ADC110, ADC134 & ADC140 CIVIC/ACCORD * 2 >99 TYPE 6 ADC110, ADC134 & ADC140 CIVIC/ACCORD * 1 >99 TYPE 5 ADC134 & ADC141 CIVIC/ACCORD * 2 >99 TYPE 6 ADC134 & ADC141 ACCORD 98-02 TYPE 2C ADC110 & ADC134 ACCORD 98-02 TYPE 2A ADC110 & ADC134 ACCORD 2003 TYPE 4 ADC110 & ADC134 CIVIC 01-02 TYPE 3 ADC110 & ADC134 CIVIC 2003 TYPE 3 ADC110 & ADC134 CR-V 02-03 TYPE 3 ADC110 & ADC134 ELEMENT 2003 TYPE 3
APPLICATIONS ACURA VEHICLE YEAR SYSTEM CABLE NSX 97-03 TYPE 1A ADC110 & ADC134 RL 00-03 TYPE 1B ADC110 & ADC134 RL 96-99 TYPE 1C ADC110 & ADC134 CL 99-03 TYPE 2A ADC110 & ADC134 INTEGRA 00-01 TYPE 2A ADC110 & ADC134 MDX 01-03 TYPE 2B ADC110 & ADC134 RSX 02-03 TYPE 3 ADC110 & ADC134 TL 99-03 TYPE 2A ADC110 & ADC134 TSX 2004 TYPE 4 ADC110 & ADC134 *1 USES OLD 5 or 3 PIN ADAPTOR CABLE—BLACK KEY SYSTEM *2 USES OLD 5 or 3 PIN ADAPTOR CABLE— RED MASTER KEY SYSTEM 121 9
GENERAL OPERATION SYSTEM DESCRIPTIONS Introduction An immobiliser system was fitted as standard equipment on this range of Honda vehicles, which prevents the vehicle from starting unless a programmed key is used. There are 4 types of immobiliser system used, which vary slightly in operation.
GENERAL OPERATION Type 1 In addition to the master and valet keys this system includes a learning key which has a unique ID code that is matched to a particular vehicle’s immobiliser control unit. It allows the immobiliser control unit to be re-programmed to either add additional programmed keys and/or delete ID codes of lost keys. Important Note: The learning key will not start the engine and may damage the immobiliser control unit if attempted.
GENERAL OPERATION Immobiliser Receiver - (Type 1 & 2) The receiver is an electrical coil embedded within the ignition switch bezel. Power is provided by the immobiliser control unit (Type 1) or the ECU (Type 2) and when a programmed key is inserted into the ignition switch the transponder is energised by electromagnetic induction. Once energised the transponder transmits its ID code to the receiver, which is then transmitted to the control unit (Type 1) or the ECM (Type 2).
GENERAL OPERATION Engine Control Module (ECU) - (All types) Type 1,3 & 4 When the ECU receives the unique serial code, it communicates back to the immobiliser control unit by transmitting back its own unique serial code. If both unique codes are mutually accepted, the ECU energises both the fuel supply and ignition system, thus allowing the engine to start.
SPECIAL FUNCTIONS TYPE 1 IMMOBILISER SYSTEM The following procedure is used for: • Programming additional keys Note: If all keys, master key or learning key are lost then a replacement immobiliser control unit set is required. • Rewriting/Replacing Immobiliser control unit • Matching the Immobiliser control unit and ECU. VEHICLE SELECTION MENU HONDA PRESS ENTER KEY At the VEHICLE SELECTION menu select the required vehicle and press the ENTER key.
SPECIAL FUNCTIONS DIAGNOSTIC MENU ECU IDENTIFICATION SPECIAL FUNCTIONS Select SPECIAL FUNCTIONS and press the ENTER key. DIAGNOSTIC MENU PROGRAM KEYS KEY INFORMATION REWRITE IMMOBILISER NO OF ORIGINAL KEYS: INCLUDE RED LEARNING KEY REWRITE IMMOBILISER Select PROGRAM KEYS and press the ENTER key. Enter number of original (master) keys NOTE : Please use RED learning key supplied with IMMO box as one original key.
SPECIAL FUNCTIONS PROGRAM KEYS SWITCH IGNITION OFF WITHIN 17 SEC ORIGINAL KEY If you entered more than ‘0’ when prompted to ‘enter number of new keys’ you will be asked to perform steps A & B. IF PROGRAMMING ADDITIONAL KEYS FOLLOW STEPS A & B 9 STEP A PROGRAM KEYS SWITCH IGNITION ON WITH NEW KEY WITHIN 20 SEC Steps A & B will be repeated for the number of new keys that are being programmed. Remember to use each new key when prompted.
SPECIAL FUNCTIONS PROGRAMMING ADDITIONAL KEYS FOLLOW STEPS C & D STEP C SWITCH IGNITION ON WITH NEW KEY STEP D SWITCH IGNITION OFF SWITCH IGNITION ON WITH ORIGINAL KEY If you entered more than ‘0’ when prompted to ‘enter number of new keys’ you will be asked to perform steps C & D. Steps C & D will be repeated for the number of new keys that are being programmed. Remember to use each new key when prompted.
SPECIAL FUNCTIONS TYPE 2 (a & b), 3 & 4 IMMOBILISER SYSTEMS The following procedure is used for: • Programming additional keys Note: If all keys, master key or learning key are lost then a replacement immobiliser control unit set is required. • Rewriting/Replacing Immobiliser control unit • Matching the Immobiliser control unit and ECU.
SPECIAL FUNCTIONS DIAGNOSTIC MENU PROGRAM KEYS KEY INFORMATION PROGRAM KEYS TOTAL KEYS REQUIRED: PROGRAM KEYS SWITCH IGNITION OFF Select PROGRAM KEYS and press the ENTER key. Enter number of new keys to be programmed and press ENTER. Note: Enter ‘0’ to either rewrite/ replace the immobiliser control unit or matching the ECM without programming any additional keys.
SPECIAL FUNCTIONS PROGRAM KEYS SWITCH IGNITION ON WITH SAME KEY WITHIN 17 SEC Check immobiliser light on the instrument panel. Select ‘YES or NO’ and press ENTER. WAIT FOR 10 SEC IS IMMO. LIGHT OUT 1. YES 2. NO SWITCH IGNITION OFF SWITCH IGNITION ON KEY INFORMATION SYSTEM: 1 KEYS STORED: ?? TYPE: ?? 132 9 Entering ‘NO’ will direct you back to the ‘DIAGNOSTIC MENU’. Procedure Complete System: 1 indicates immobiliser system ok. Keys Stored: Indicates number of keys programmed.
TIPS & HINTS The procedure for coding keys on the AD100 is merely a text walkthrough (wait 17 secs, turn key off etc)- it is completely unaffected by the transponder type or indeed whether a transponder is fitted in the key or not. This is the reason for the immobiliser light continuing to flash after the keys have been programmed. The question "is the warning light off" during the programming procedure is a response to procedure rather than an actual consequence of correct programming.
10 HYUNDAI
HYUNDAI MANUAL CONTENTS APM116 PAGE APPLICATIONS 136 GENERAL OPERATION 137 SPECIAL FUNCTIONS 139 TIPS & HINTS 144 7 10
APPLICATIONS MODEL ATOS ACCENT EXCEL S COUPE MATRIX ELANTRA HD COUPE SONATA XG MARCIA CENTENNIAL GRANDEUR H-100 H-100 TRUCK H-1 H-1 TRUCK SANTA FE TRAJET XG TAXI TERRACAN GALLOPER SANTAMO 136 CABLE ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 ADC110 10
GENERAL OPERATION INTRODUCTION The Hyundai Immobiliser system called the SMARTRA manufactured by Bosch consists of the SMARTRA ECU which has its own CPU which controls the vehicles immobiliser in conjunction with the engine management ECU. There are 3 basic systems used on the range of vehicles :SYSTEM 1 BLACK key system—TEXTON Read only key head Minimum keys required for programming 1. Maximum keys programmed 5. SYSTEM 2 BLUE key system—ENCRYPT key system Minimum keys required for programming 1.
GENERAL OPERATION KEY PROGRAMMING (WITH MASTER KEY) Elantra, Lantra, Coupe, S Coupe, Sonata, Sonica, Accent Atos, Starex Galloper 1996 + 1998 + 1999 + Procedure 1. 2. 3. 4. 5. 6. Insert Master Key in ignition. Switch Ignition OFF to ON 5 times. Remove Master key. Insert NEW key into IGNITION and TURN IGNITION ON. Turn ignition OFF and remove key. Repeat 4 to 5 for all additional keys and any existing keys. NOTE : IF AN EXISTING KEY IS NOT REGISTERED AT THIS STAGE THEN IT WILL BE DELETED FROM THE SYSTEM.
SPECIAL FUNCTIONS KEY PROGRAMMING—SYSTEM 1 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU 10 Select PROGRAM KEYS. > PROGRAM KEYS > CLEAR KEYS > KEYS PROGRAMMED PRESS ENTER KEY Enter security code. SECURITY CODE ____ NOTE : This code is normally 2345 NOTE 2 : If this is incorrect then the dealer who supplied the vehicle may have changed it. If this is so, please contact the dealer.
SPECIAL FUNCTIONS KEY CLEARING—SYSTEM 1 DIAGNOSTIC MENU > PROGRAM KEYS > CLEAR KEYS > KEYS PROGRAMMED Select CLEAR KEYS from SPECIAL FUNCTIONS menu. PRESS ENTER KEY Enter security code. SECURITY CODE ____ NOTE : This code is normally 2345 NOTE 2 : If this is incorrect then the dealer who supplied the vehicle may have changed it. If this is so, please contact the dealer.
SPECIAL FUNCTIONS KEY PROGRAMMING—SYSTEM 2 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY 10 DIAGNOSTIC MENU > PROGRAM KEYS > KEYS PROGRAMMED > LIMP HOME MODE Select PROGRAM KEYS. PRESS ENTER KEY Enter 6 digit security code. SECURITY CODE ______ SECURITY CODE NOTE : The 6 digit code is available from the vehicle dealer.
SPECIAL FUNCTIONS KEY PROGRAMMING—SYSTEM 2 PROGRAM KEYS INSERT NEXT KEY & THEN PRESS ENTER The key in the ignition will be added to the system. To program additional keys press the ENTER key, or BACK to exit programming. PROGRAM KEYS PROCEDURE COMPLETE If ENTER is pressed then additional keys can be programmed. Repeat for all additional keys. If BACK is pressed then and all keys have been programmed the PROCEDURE COMPLETE is displayed.
SPECIAL FUNCTIONS SYSTEM 1—ECU CODING/PIN CODE READ & WRITE Process for coding Hyundai SYSTEM 1 keys is as follows. Procedure 1 – First thing to do after communications are established is read the pin code and make sure this matches the last 5 digits of the chassis number 2 – If the pin code and chassis number match you can program keys normally entering the pin code 3 – If pin code and chassis number are different then the pin code need to be changed.
TIPS & HINTS When programming keys, please note the following: The transponder aerial has a resistance of 21.5 Ohms The immobiliser control unit does not return any information to the tester about the key programming procedure, therefore it is possible to input an incorrect security code and continue through the programming procedure. When programming a key, the horn will sound for 0.2 second to signify the key programming action.
11 JAGUAR
JAGUAR MANUAL CONTENTS APM105 PAGE APPLICATIONS 146 GENERAL OPERATION 147 SPECIAL FUNCTIONS 148 7 11
APPLICATIONS VEHICLE TYPE KEYS CABLE XJ PETROL 2 KEYS ADC110 XK PETROL 2 KEYS ADC110 X-TYPE PETROL 2 KEYS ADC110 S-TYPE PETROL 2 KEYS ADC110 147 11
GENERAL OPERATION SYSTEM OPERATION The PATS system is a PASSIVE Anti-theft system which requires no special procedures for the driver to arm or disarm the system. The system is operated by a transponder fitted within the ignition key’s body, which communicates with the PATS module transceiver mounted around the lock barrel. The easy method of identifying a PATS vehicle is if the key has a small imprint showing where the transponder is fitted.
SPECIAL FUNCTIONS CLEARING PATS 3 SYSTEM CLEAR PATS 3 SYSTEM MIN KEYS REQUIRED : 2 TIMED ACCESS CLEAR TIME 10:00 KEYS PROGRAMMED : 2 PRESS ENTER KEY CLEAR PATS 3 KEY GAINING ACCESS TIME ELAPSED 0:50 TIME REQUIRED 10:00 ACCESS STATUS IN PROGRESS BACK TO ABORT Follow the screen instructions to clear the PATS system. The AD100 will now start to clear the PATS system key codes from memory. 11 After clearing, the PATS system will automatically read the key in the ignition.
12 KIA
KIA MANUAL CONTENTS APPLICATIONS 151 GENERAL OPERATION 152 SPECIAL FUNCTIONS 154 TIPS & HINTS APM117 PAGE 159 7 12
APPLICATIONS MODEL CABLE PRIDE ADC110 VISTO ADC110 AVELLA ADC110 RIO ADC110 SEPHIA ADC110 SHUMA ADC110 CARENS ADC110 SPORTAGE ADC110 CLARUS ADC110 OPTIMA/MAGENTIS ADC110 ELAN ADC110 POTENTIA ADC110 ENTERPRISE ADC110 CARNIVAL/SEDONA ADC110 RETONA ADC110 JOICE ADC110 TOWNER ADC110 PREGIO ADC110 FRONTIER ADC110 152 12
GENERAL OPERATION INTRODUCTION The Kia Immobiliser system called the SMARTRA manufactured by Bosch consists of the SMARTRA ECU which has its own CPU which controls the vehicles immobiliser in conjunction with the engine management ECU. There are 3 basic systems used on the range of vehicles :SYSTEM 1 BLACK key system—TEXTON Read only key head Minimum keys required for programming 1. Maximum keys programmed 5. SYSTEM 2 BLUE key system—ENCRYPT key system Minimum keys required for programming 1.
SPECIAL FUNCTIONS KEY PROGRAMMING—SYSTEM 1 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU Select PROGRAM KEYS. > PROGRAM KEYS > CLEAR KEYS > KEYS PROGRAMMED PRESS ENTER KEY Enter security code. SECURITY CODE ____ NOTE : This code is normally 2345 NOTE 2 : If this is incorrect then the dealer who supplied the vehicle may have changed it. If this is so, please contact the dealer.
SPECIAL FUNCTIONS KEY CLEARING—SYSTEM 1 DIAGNOSTIC MENU > PROGRAM KEYS > CLEAR KEYS > KEYS PROGRAMMED Select CLEAR KEYS from SPECIAL FUNCTIONS menu. PRESS ENTER KEY Enter security code. SECURITY CODE ____ NOTE : This code is normally 2345 NOTE 2 : If this is incorrect then the dealer who supplied the vehicle may have changed it. If this is so, please contact the dealer.
SPECIAL FUNCTIONS KEY PROGRAMMING—SYSTEM 2 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS > KEYS PROGRAMMED > LIMP HOME MODE Select PROGRAM KEYS. PRESS ENTER KEY Enter 6 digit security code. SECURITY CODE ______ SECURITY CODE NOTE : The 6 digit code is available from the vehicle dealer.
SPECIAL FUNCTIONS KEY PROGRAMMING—SYSTEM 2 PROGRAM KEYS INSERT NEXT KEY & THEN PRESS ENTER The key in the ignition will be added to the system. To program additional keys press the ENTER key, or BACK to exit programming. PROGRAM KEYS PROCEDURE COMPLETE If ENTER is pressed then additional keys can be programmed. Repeat for all additional keys. If BACK is pressed then and all keys have been programmed the PROCEDURE COMPLETE is displayed.
SPECIAL FUNCTIONS SYSTEM 1—ECU CODING/PIN CODE READ & WRITE Process for coding Kia SYSTEM 1 keys is as follows. Procedure 1 – First thing to do after communications are established is read the pin code and make sure this matches the last 5 digits of the chassis number 2 – If the pin code and chassis number match you can program keys normally entering the pin code 3 – If pin code and chassis number are different then the pin code need to be changed.
TIPS & HINTS When programming keys, please note the following: The transponder aerial has a resistance of 21.5 Ohms The immobiliser control unit does not return any information to the tester about the key programming procedure, therefore it is possible to input an incorrect security code and continue through the programming procedure. When programming a key, the horn will sound for 0.2 second to signify the key programming action.
13 LAND ROVER
LAND ROVER MANUAL CONTENTS PAGE APPLICATIONS 160 GENERAL OPERATION 161 SPECIAL FUNCTIONS 167 7 13 APM104
APPLICATIONS VEHICLE SYSTEM YEAR CABLE CLASSIC RANGE ROVER 10AS 95 ADC110 DEFENDER 10AS 95 ADC110 DISCOVERY (OLD) 10AS 95 ADC110 FREELANDER 27VT 95 ADC110 NOTE : THE SYSTEMS ABOVE USE THE REMOTE PLIP UNIT AS PICTURED BELOW.
GENERAL OPERATION SYSTEM DESCRIPTION (10AS ALARM SYSTEM) INTRODUCTION The 10AS Alarm system was fitted as standard equipment on Model Year 96 onwards across a number of Land Rover vehicles.
GENERAL OPERATION The battery backed up sounder is charged via the ignition feed, and if disconnected or wires cut it will operate for approximately 3 minutes. To disconnect the battery backed up sounder follow the following procedure :1. 2. 3. 4. 5. Turn Ignition ON, Turn Ignition OFF Disconnect Sounder within 15 seconds If Triggered, Re-connect. Disarm Alarm system Turn Ignition on and repeat steps above.
GENERAL OPERATION VEHICLE STATUS INDICATION The vehicle status is indicated by the Alarm LED as follows :• • • • • Slow flash - Immobilised or Armed and Immobilised Rapid Flash - Internal sensor system armed Intermittent Rapid Flash - Doors, Boot and Bonnet armed No flash for 10 seconds - Miss lock Continuous - Drivers door open or ignition on and system immobilised PLIP KEY RESYNCHRONISATION Procedure. 1. Unlock the drivers door using the key. 2.
GENERAL OPERATION SYSTEM DESCRIPTION (27VT (BCM) SECURITY SYSTEM) INTRODUCTION The 27VT and BCM (Body Control Module) is a sophisticated alarm system and central locking control, which has a number of associated components that make up the system, which includes :• Remote Handset (Plip Key) • RF Receiver • Passive Coil • Volumetric sensor • Door Lock actuators • Drivers door key barrel • Central door key barrel • Central Door Locking switch (CDL) • Door switches • Tail door switch • Bonnet switch • Horn • A
GENERAL OPERATION INERTIA SWITCH The inertia switch is located within the engine bay, on the bulkhead. If the ignition is ON and the alarm disarmed, then if the switch is operated then all the doors will be unlocked. Further locking of all doors is disabled until the ignition is switched off and the drivers door opened and closed or the drivers door opened and closed and the switch is manually reset by pressing the button.
GENERAL OPERATION • • • • • Drivers door is unlocked, other doors remain locked. Alarm LED flashes slowly Perimetric protection is de-activated Volumetric protection is de-activated Engine and crank functions remain disabled. The EKA code is a four number code, and each number can be up to 15. This code is entered by turning the drivers door lock to the numbers of the code. Procedure for 5-2-9-14 1. Turn the key to the unlock position and wait for 6 MINUTES before proceeding. 2.
SPECIAL FUNCTIONS PROGRAMMING REMOTE PLIP KEYS (27VT) VEHICLE SELECTION MENU FREELANDER DISCOVERY RANGE ROVER CLASSIC DEFENDER At the VEHICLE SELECTION menu select the required vehicle. Then press the ENTER key. PRESS ENTER KEY TURN IGNITION ON Turn Ignition ON and press the ENTER key. 13 PRESS ENTER KEY PLEASE WAIT TRYING TO COMMUNICATE The AD100 will now attempt to communicate with the ECU. ECU IDENTIFICATION PRODUCT CODE : 27 DIAG.VERS.:11 SOFTWARE VERSION:15 HARDW.VERS:382 ECU NO.
SPECIAL FUNCTIONS PROGRAMMING REMOTE PLIP KEYS (27VT) DIAGNOSTIC MENU PROGRAM PLIP READ EKA CODE PROGRAM PLIP PRESS PLIP UNLOCK AT LEAST 8 TIMES UNTIL HORN SOUNDS OR LIGHTS FLASH KEYS PROGRAMMED : 1 PRESS BACK TO EXIT ENTER—PROG MORE KEYS Select PROGRAM PLIP and press enter button. Press the unlock button on the PLIP key quickly up to 8 times, or until horn sounds. If key has been programmed successfully the screen opposite should display how many PLIP keys have been programmed.
SPECIAL FUNCTIONS PROGRAMMING REMOTE PLIP KEYS (10AS) VEHICLE SELECTION MENU FREELANDER DISCOVERY RANGE ROVER CLASSIC DEFENDER At the VEHICLE SELECTION menu select the required vehicle. Then press the ENTER key. PRESS ENTER KEY TURN IGNITION ON Turn Ignition ON and press the ENTER key. 13 PRESS ENTER KEY PLEASE WAIT TRYING TO COMMUNICATE ECU IDENTIFICATION LUCAS 10AS The AD100 will now attempt to communicate with the ECU.
SPECIAL FUNCTIONS PROGRAMMING REMOTE PLIP KEYS (10AS) PROGRAM PLIP PRESS PLIP UNLOCK AT LEAST 8 TIMES UNTIL HORN SOUNDS OR LIGHTS FLASH Press the unlock button on the PLIP key quickly up to 8 times, or until alarm/ horn sounds or lights flash. Repeat for up to 4 Plip keys by pressing ENTER or BACK to exit. TO RE-SYNCHRONISE PLIPS PRESS THE UNLOCK BUTTON 4 TIMES As a reminder, if the Plip keys are not synchronised, then please synchronise all keys as previously explained.
14 MAZDA
MAZDA MANUAL CONTENTS PAGE APPLICATIONS 173 SPECIAL FUNCTIONS 174 7 14 APM125
APPLICATIONS VEHICLE YEAR KEY PROG TYPE 626 ALL Y LUCAS XEDOS ALL Y LUCAS DEMIO ALL Y LUCAS 14 175
SPECIAL FUNCTIONS MAZDA CODE CONVERTER VEHICEL SELECTION LEXUS MAZDA MITSUBISHI NISSAN From the VEHICLE SELECTION MENU select MAZDA. PRESS ENTER KEY DIAGNOSTIC MENU > PATS 2 > P.C.M > MAZDA PIN CODE Select MAZDA PIN CODE 14 PRESS ENTER KEY Press ENTER Key MAZDA CODE CONVERTER PRESS ENTER KEY SERIAL CODE Enter serial number from LUCAS Immobiliser mounted at the back of the IGNITION KEY assembly. __________ Code can be found on the label.
SPECIAL FUNCTIONS MAZDA CODE CONVERTER MAZDA MECS SER No. 603-611-2057 PINCODE : 7355-4316 The screen will then displayed the converted pin code. PRESS ENTER KEY KEY PROGRAMMING PROCEDURE PROCEDURE FOR WHEN THERE ARE NO KEYS OR ONLY 1 PREPROGRAMMED KEY AND YOU NEED TO PROGRAM MORE KEYS IMPORTANT : You must have at least 2 keys to perform this procedure. If there are no pre-programmed keys, you will have to provide 2 new keys.
SPECIAL FUNCTIONS PROGRAMMING PROCEDURE PROCEDURE FOR WHEN THERE ARE 2 OR MORE PREPROGRAMMED KEYS 1. 2. 3. 4. 5. 6. 7. 8. Cut the mechanical cuts on each new transponder key. Insert the first key and turn the ignition ON and then back to the OFF position 5 times. You must NOT leave the ignition in the ON position for more than 1 second. Turn the first pre-programmed key back to the ON position, the security light should stay ON. Turn the first key back to the LOCK position.
SPECIAL FUNCTIONS 4 5 6 7 8 9 10 Within 30 seconds of turning the key to the LOCK position, turn the ignition key to the ON position while the security light is not illuminated. Count the illumination flashes 2 times while the light is not illuminated and turn the key to the lock position. Within 30 seconds of turning the key to the LOCK position, turn the ignition key to the ON position while the security light is not illuminated.
15 MITSUBISHI
MITSUBISHI MANUAL CONTENTS PAGE APPLICATIONS 180 GENERAL OPERATION 181 SPECIAL FUNCTIONS 183 7 15 APM114
APPLICATIONS VEHICLE YEAR CABLE 3000GT ALL MODELS ADC129 CHALLENGER ALL MODELS ADC129 COLT ALL MODELS ADC129 EXPRESS VAN ALL MODELS ADC129 GALANT WAGON ALL MODELS ADC129 LANCER ALL MODELS ADC129 LANCER WAGON ALL MODELS ADC129 MAGNA ALL MODELS ADC129 NIMBUS 95 ADC129 NIMBUS 99 ADC129 PAJERO 97 ADC129 PAJERO 2000 ADC129 PAJERO IO ALL MODELS ADC129 TRITON ALL MODELS ADC129 VERADA ALL MODELS ADC129 CARISMA ALL MODELS ADC129 ECLIPSE ALL MODELS ADC129 GALANT 9
GENERAL OPERATION INTRODUCTION The Mitsubishi Anti Theft system can be coded for up to 8 keys into the system memory. When new keys are added all existing keys are deleted from the memory, so it is important to ensure all keys are with the vehicle at the time of programming. The system is made up of Ignition switch, key antenna, mounted around the ignition switch and immobiliser ECU.
SPECIAL FUNCTIONS KEY PROGRAMMING—ALL SYSTEMS DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS PRESS ENTER KEY BACK TO EXIT ENTER TO PROGRAM NEXT KEY INSERT NEXT KEY SWITCH IGNITION ON AND PRESS ENTER WITHIN 5 SECONDS Select PROGRAM KEYS. NOTE : The AD100 will automatically input the correct Pin code into the system. If it is wrong INCORRECT ACCESS CODE will be displayed.
TIPS & HINTS WARNINGS 1. DO NOT INSERT UNPROGRAMMED KEY INTO IGNITION AND SWITCH OFF, UNTIL PROGRAMMING IS COMPLETE. OTHERWISE THE SYSTEM WILL ENTER THEFT MODE. TO OVERCOME THEFT MODE LEAVE THE IGNTION ON FOR 25 MINUTES AND THEN PROGRAM KEY. 2. IF AN ERROR IS RECEIVED WHEN PROGRAMMING KEYS, CHECK THE CORRECT CABLE IS BEING USED, ADC129. 3.
16 NISSAN
NISSAN MANUAL CONTENTS PAGE APPLICATIONS 186 GENERAL OPERATION 187 SPECIAL FUNCTIONS 190 7 16 APM109
APPLICATIONS VEHICLE ENG TYPE MODEL YEAR SYSTEM CABLE ALMERA PETROL >2000 NATS 2,3 & 4 ADC133 + ADC136 ALMERA PETROL 2000> NATS 5 ADC110 ALMERA ALL 2000 MY NATS RED CHIP (OBD) ADC133 + ADC135 ALMERA DIESEL >2000 NATS 2,3 & 4 ADC133 + ADC136 ALMERA DIESEL 2000> NATS 5 ADC110 ALMERA TINO PETROL ALL MODELS NATS 5 ADC110 ALMERA TINO DIESEL ALL MODELS NATS 5 ADC110 CABSTAR PETROL ALL MODELS NATS 2 ADC133 + ADC136 CABSTAR DIESEL ALL MODELS NATS 2 ADC133 + ADC136 D2
GENERAL OPERATION INTRODUCTION The Nissan Anti Theft System (NATS) was introduced initially around 1995 with a basic immobiliser, which did not use key transponders. This system was known as NATS 1. Subsequently NATS 2 was introduced which uses the transponder technology. Further iterations of the NATS system have been introduced, up to the latest system NATS 5. The earlier systems use a security timed access, similar to Ford systems, which require a period of time before the keys can be programmed.
LED ON LED ON NATS FAULT AND ENGINE COMPONENT FAULT ENGINE FAULT 6 FLASHES 6FLASHES & ON AFTER IGN IS SWITCHED ON NATS FAULT (DONGLE FAULT) AFTER NATS PROGRA,MMING REMAINS ON FOR 15 MINUTES AFTER IGN IS SWITCHED ON NATS LED 6FLASHES& ON AFTER IGN IS SWITCHED ON ENGINE CHECK LIGHT WITH DONGLE NATS FAULT (NO DONGLE FAULT) CONDITION LED ON LED ON ENGINE CHECK LIGHT LED ON LED ON NATS LED WITHOUT DONGLE GENERAL OPERATION NATS LED FUNCTION TABLE 16
GENERAL OPERATION IMMU ECM received a signal from IMMU, indicating that IMMU is malfunctioning. ECM Control unit is faulty CHAIN OF ECM-IMMU Communication between ECM and IMMU DIFFERENCE OF KEY IMMU can receive the Key ID signal but ID verification between Key ID and IMMU is incorrect. CHAIN OF IMMU KEY IMMU cannot receive key ID & Dongle unit is malfunctioning (IF FITTED) 16 ID DISCORD, IMM-ECM The result of ID verification between IMMU and ECM is no good. System programming is required.
SPECIAL FUNCTIONS KEY PROGRAMMING—NATS 2,3 & 4 (PETROL) DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS Select SPECIAL FUNCTIONS from menu. Select PROGRAM KEYS The System takes approximately 16 minutes to clear. After clearing, the key in the IGNITION will be registered. Remove the key from ignition and insert next key. Turn ignition ON for 5 seconds. Then turn off and remove key. Repeat for up to 5 keys.
SPECIAL FUNCTIONS KEY PROGRAMMING—NATS 5 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS Select SPECIAL FUNCTIONS from menu. PRESS ENTER KEY DIAGNOSTIC MENU PROGRAM KEYS PRESS ENTER KEY SECURITY CODE Select PROGRAM KEYS from selection. Enter the 4 digit security code. Then follow on screen instructions. The key in the ignition will be registered first, then program additional keys as follows :Turn ignition ON for 5 seconds. Then turn off and remove key.
17 PEUGEOT
PEUGEOT MANUAL CONTENTS PAGE APPLICATIONS 194 GENERAL OPERATION 195 SPECIAL FUNCTIONS 196 7 17 APM107
APPLICATIONS VEHICLE YEAR SYSTEM CABLE 106 1997 ON IMMO 1 ADC110 206 1997 ON CPH ADC110 206 1997 ON BSI ADC110 306 1997 ON IMMO 1 ADC110 306 1997 ON CPH ADC110 307 2001 ON BSI ADC110 406 97-99 IMMO1 ADC100 + ADC120 NEW 406 99 ON BSI ADC110 406 COUPE 97 ON CPH ADC110 607 2001 ON BSI ADC110 806 1997 ON CPH ADC110 EXPERT 1997 ON CPH ADC110 PARTNER 1997 ON IMMO 1 ADC110 PARTNER 1997 ON BSI ADC110 RANCH 1997 ON IMMO 1 ADC110 196 17
GENERAL OPERATION INTRODUCTION The Peugeot Immobiliser systems are made up of 3 different types. They all perform various functions, and it is important to understand the basic configuration and the types of systems fitted. IMM– STANDARD IMMOBILISER This system was the first transponder system fitted to the Peugeot range of vehicles, after the keypad system was phased out.
SPECIAL FUNCTIONS PROGRAMMING KEYS—IMMOBILISER 1 SYSTEM DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES LIVE DATA ACTUATORS SPECIAL FUNCTIONS PRESS ENTER KEY DIAGNOSTIC MENU PROGRAM KEYS Select SPECIAL FUNCTIONS from the Diagnostic Menu using the UP and DOWN arrows. Then press the ENTER key. NOTE : ENSURE ALL DOORS ALL CLOSED WHEN KEY PROGRAMMING IS BEING PERFORMED.
SPECIAL FUNCTIONS PROGRAMMING KEYS TOTAL KEYS REQUIRED : 2 If Access code is correct, ENTER the number of keys to program. NOTE : Max 4 keys can be added. PRESS ENTER KEY SWITCH IGNITION ON IGNITION STATUS OFF SWITCH IGNITION OFF IGNITION STATUS ON Follow on screen instruction for programming the keys. After switching IGNTION OFF remove the key and repeat procedure for additional keys.
SPECIAL FUNCTIONS SECURITY CODE ____ To enter the security code use the following procedure :Press SECURITY CODE X4YT IS THIS CORRECT OK=ENTER CLEAR=BACK Press tion to select Number & Letter To Erase the previous selec- Press To ENTER selection. Press To Finish PIN selection. NOTE : AFTER PROGRAMMING CLEAR FAULT CODES AND LOCK VEHICLE FOR 10 MINUTES BEFORE TRYING THE KEY OR PLIP. WARNING : WHEN PROGRAMMING KEYS, THE SYSTEM AUTOMATICALLY ERASES THE PLIP KEYS AT THE SAME TIME.
SPECIAL FUNCTIONS SWITCH IGNITION ON SWITCH IGNITION OFF REMOVE KEY FROM IGNITION INSERT NEXT KEY SWITCH IGNITION ON IGNITION STATUS OFF NOTE : AFTER PROGRAMMING CLEAR FAULT CODES AND LOCK VEHICLE FOR 10 MINUTES BEFORE TRYING THE KEY OR PLIP.
18 PROTON
PROTON MANUAL CONTENTS PAGE APPLICATIONS 202 GENERAL OPERATION 203 SPECIAL FUNCTIONS 204 7 18 APM123
APPLICATIONS VEHICLE YEAR KEY PROG TYPE CABLE ISWARA ALL Y TYPE 1,2 or 3 ADC110 or ADC129 PUTRA ALL Y TYPE 1,2 or 3 ADC110 or ADC129 PERDANA ALL Y TYPE 1,2 or 3 ADC110 or ADC129 WAJA ALL Y TYPE 1,2 or 3 ADC110 or ADC129 JUMPUCK GLSi ALL Y TYPE 1,2 or 3 ADC110 or ADC129 JUMPBUCK GLi ALL Y TYPE 1,2 or 3 ADC110 or ADC129 SATRIA GTi ALL Y TYPE 1,2 or 3 ADC110 or ADC129 SATRIA XLs ALL Y TYPE 1,2 or 3 ADC110 or ADC129 SATRIA GLi ALL Y TYPE 1,2 or 3 ADC110 or ADC129
GENERAL OPERATION INTRODUCTION There are 3 different immobiliser systems fitted to the Proton vehicle range as follows :NOTE : Always make sure that you are fully aware of the difference between Type 2 BLUE keys and Type 3 BLUE keys before programming. NOTE : When programming Impian keys, the alarm will need programming as well, details below. IMPIAN/JUMBUCK Alarm Fob reprogramming 1. Alram system must be disarmed before procedure using the reset switch or ignition key. 2.
SPECIAL FUNCTIONS KEY PROGRAMMING—TYPE 1 & TYPE 2 DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select the SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU Select PROGRAM KEYS. > PROGRAM KEYS PRESS ENTER KEY BACK TO EXIT ENTER TO PROGRAM NEXT KEY NOTE : If the system has been accessed incorrectly by another piece of equipment then a security wait time of 16 minutes is required before attempting to program keys.
SPECIAL FUNCTIONS DIAGNOSTIC MENU > PROGRAM KEYS Select PROGRAM KEYS. PRESS ENTER KEY BACK TO EXIT ENTER TO PROGRAM NEXT KEY If further keys are required then press the ENTER key. IF ENTER IS PRESS THEN THIS SCREEN WILL APPEAR. REMOVE KEY FROM IGNITION INSERT NEXT KEY PRESS ENTER PROGRAM KEYS PROCEDURE COMPLETE PRESS ENTER 207 Repeat this procedure for all additional keys.
19 RENAULT
RENAULT MANUAL CONTENTS PAGE APPLICATIONS 208 GENERAL OPERATION 209 SPECIAL FUNCTIONS 215 7 19 APM106
APPLICATIONS VEHICLE MODEL YEAR CABLE CLIO II ALL MODELS ADC110 KANGOO II ALL MODELS ADC110 MEGANE 99 >ON ADC110 MEGANE SCENIC 99 > ON ADC110 LAGUNA II ALL MODELS ADC110 TRAFFIC II ALL MODELS ADC110 KANGOO II SYSTEM IDENTIFICATION NORMAL KANGOO 19 KANGOO II 210
GENERAL OPERATION INTRODUCTION The Renault Immobiliser system uses either Infra Red or Radio Frequency for Plip key operation and transponder key technology for key entry and starting. The Infra Red and RF systems uses a rolling code system to ensure the vehicle system cannot be breached. Activation of the Immobiliser system is indicated by the LED indicator in the Instrument cluster.
GENERAL OPERATION Decoder Unit (BII) This system is similar to many other immobiliser systems as it uses a transponder within the head of the key to send its code to the immobiliser when interrogated via the immobiliser ignition key barrel antenna.
GENERAL OPERATION Coded Card The coded card system was introduced for the latest Laguna models and eliminates the use of 'ignition keys' and, optionally, 'door locking keys'.
GENERAL OPERATION Model Kangoo Master (XD0) Clio I Clio II Safrane Laguna I Year Immobiliser Type Version 10/97 D V2 10/97 F V2 10/97 H V2 10/97 D V2 10/97 F V2 10/97 H V2 07/94 A V1 04/95 C V1 04/95 D V1 & V2 12/95 F V2 12/96 E V2 03/98 H V2 06/01 J V3 01/93 A V1 05/93 B V1 02/95 C V1 10/95 E V2 09/96 G V2 01/97 H V2 02/94 A V1 07/94 B V1 01/95 C V1 11/95 D V1 & V2 09/95 E V2 11/95 F V2 01/97 H V2 Laguna II 01/00 J V3
GENERAL OPERATION All systems have the same end function, immobilizing the vehicle until the correct code is presented to the immobiliser unit. Type 'A' Infrared Remote Control Fixed Code - Petrol This system uses a combined immobiliser and central door locking control unit with a remote infrared transmitter contained in the plastic keyhead. The transmitted code is fixed and when received by the control unit receiver it will generate a door open signal and simultaneously pass the code to the EMS-ECM.
GENERAL OPERATION Type 'E' Infrared Remote Control Rolling Code - Diesel This system uses a combined immobiliser and central door locking control unit with a remote infrared transmitter contained in the plastic keyhead. The transmitted code is rolling to reduce the chances of the code being captured and used to enter the vehicle. The code when received by the control unit receiver it will generate a door open signal and simultaneously pass the code to the Coded Solenoid Valve.
SPECIAL FUNCTIONS KEY PROGRAMMING—ALL SYSTEMS DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS From the main DIAGNOSTIC MENU select SPECIAL FUNCTIONS. PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS Select PROGRAM KEYS. PRESS ENTER KEY SWITCH IGNITION OFF To enter the security code use the following procedure :- SECURITY CODE Press ____________ Press To Erase the previous selection Press To ENTER selection. Press To Finish PIN selection.
20 ROVER
ROVER MANUAL CONTENTS PAGE APPLICATIONS 218 GENERAL OPERATION 219 SPECIAL FUNCTIONS 222 TIPS & HINTS 226 7 20 APM103
APPLICATIONS VEHICLE SYSTEM YEAR CABLE MINI 5AS 95 ON ADC100 + ADC120/ 100 5AS 95 ON ADC100 + ADC120/ 200 5AS 95 ON ADC100 + ADC120/ 400 5AS 95 ON ADC100 + ADC120 MG-F 5AS 95 ON ADC100 + ADC120 25 5AS 95 ON ADC100 + ADC120 45 5AS 95 ON ADC100 + ADC120 MEMS 1.6 MEMS 95 ON ADC125 + ADC100 MEMS 1.9 MEMS 95 ON ADC100 +ADC124 or ADC110 MEMS 2J MEMS 95 ON ADC110 NOTE : THE SYSTEMS ABOVE USE THE REMOTE PLIP UNIT AS PICTURED BELOW.
GENERAL OPERATION SYSTEM DESCRIPTION (5AS ALARM SYSTEM) INTRODUCTION There are a number of different systems fitted across the Rover vehicle range, which vary slightly. The systems can only be enabled and disabled using the Key Fob (PLIP). If the car is locked with the mechanical key only, then the alarm is not enabled. There are three ways the alarm works, one is to enable an ultrasonic alarm, the second Perimetric protection and the other engine immobilisation.
GENERAL OPERATION PLIP KEY BATTERY REPLACEMENT Ensure the vehicle is unlocked before the following procedure is followed. The battery in the Plip key should last for around 3 years, depending on usage. To change the battery, split the Plip key in half and remove the battery, taking care not to touch the clip or any of the components. Press and hold each of the Plip key buttons for 5 seconds, to discharge any residual voltage in the circuits.
GENERAL OPERATION ENGINE IMMOBILISATION OVERRIDE If the Plip key is lost or does not function, the emergency access code (EKA) can be used to override the system as follows :1. Insert the key into the drivers lock, and turn to the lock position. 2. Hold the key in this position for 5 seconds. 3. Now using the code turn the key to the unlock the number of times of the first digit. 4. Now turn the key to the lock position the number of times of the second digit. 5. Repeat for the last two digits. 6.
SPECIAL FUNCTIONS PROGRAMMING REMOTE PLIP KEYS VEHICLE SELECTION MENU MINI ROVER 100 ROVER 200 ROVER 400 ROVER MG-F At the VEHICLE SELECTION menu select the required vehicle. Then press the ENTER key. PRESS ENTER KEY DIAGNOSTIC MENU PLIP KEY FUNCTIONS EKA FUNCTION PRESS ENTER KEY Select the function required. The AD100 will now attempt to communicate with the ECU.
SPECIAL FUNCTIONS DIAGNOSTIC MENU PROGRAM PLIP KEY Select PROGRAM PLIP KEY. PRESS ENTER KEY PRESS PLIP LOCK AT LEAST 8 TIMES UNTIL HORN SOUNDS. Press either button on the Plip key very quickly up to 8 times until the horn sounds, which indicates it has been successfully programmed. Repeat up to 4 plip keys. PRESS ENTER KEY READING EKA CODE DIAGNOSTIC MENU PLIP KEY FUNCTIONS EKA FUNCTIONS PRESS ENTER KEY TURN IGNITION ON Select the EKA function.
SPECIAL FUNCTIONS PROGRAMMING EKA CODE DIAGNOSTIC MENU READ EKA CODE SPECIAL FUNCTIONS To program a new EKA code select special functions from the menu and press ENTER. PRESS ENTER KEY DIAGNOSTIC MENU WRITE EKA CODE Select write EKA code. PRESS ENTER KEY SECURITY CODE Insert new EKA code. Please make a note of this and advise the customer. ____ 20 SECURITY CODE 1234 If correct press enter to proceed.
SPECIAL FUNCTIONS RE-CODE ECU’s (MEMS 1.6, 1.9 & 2J) VEHICLE SELECTION MENU IMMOBILISER EMS At the VEHICLE SELECTION menu select the required system. Then press the ENTER key. PRESS ENTER KEY VEHICLE SELECTION MENU Select the required EMS system MEMS 1.6 MEMS 1.9 MEMS 2J PRESS ENTER KEY VEHICLE SELECTION MENU Select RE-CODE ECU RE-CODE ECU 20 PRESS ENTER KEY TURN IGNITION ON Turn Ignition ON and press the ENTER key.
TIPS & HINTS GENERAL 1. If the Plip key does not operate, it could be one of the following causes :• Bad connection at 5AS ECU plug. • Plip Key inoperative or ECU de-programmed. • System in lock out due to other radio interference. 2. Alarm LED not working, this could be the failure of LED unit, as this is common on Rover 800 vehicles. Replace LED unit. 3.
TIPS & HINTS ECU IDENTIFICATION (Contd) MEMS 1.
21 SUBARU
SUBARU MANUAL CONTENTS PAGE APPLICATIONS 230 GENERAL OPERATION 231 SPECIAL FUNCTIONS 233 7 21 APM126
APPLICATIONS VEHICLE MODEL YEAR PIN CODE REQUIRED SYSTEM CABLE BAJA SPORTS ALL N OBD ONLY AD110B BAJA TURBO ALL AD110B FORESTER X, XT, XS 96-03 MY N OBD ONLY AD110B IMPREZA SEDAN 96-03 MY N OBD ONLY AD110B IMPREZA SPORTS WAGON 96-03 N OBD ONLY AD110B LEGACY WAGON 96-03 MY N OBD ONLY AD110B LEGACY SEDAN 96-03 MY N OBD ONLY AD110B OUTBACK ALL N OBD ONLY AD110B OUTBACK SPORT ALL N OBD ONLY AD110B OUTBACK WAGON ALL N OBD ONLY AD110B OUTBACK SEDAN ALL N OBD
GENERAL OPERATION INTRODUCTION There are two types of systems fitted to Subaru vehicles that can generally be identified by the model year, however this is not always the case. Detailed below is a guide to help you determine which system is fitted. - > 2000 This system can normally be identified by having a keypad in the glovebox. These vehicles can also be fitted with a Sigma alarm that have a separate remote control. AD100 cannot be used to program these remote controls.
GENERAL OPERATION General Subaru Immobiliser info. Immobiliser operation With the vehicle stopped and the ignition off, there is a red LED on the dashboard which flashes as an anti theft deterrent with a 0.2 second on time and a 2 second off time. This indicates the vehicle is in an immobilised state. If you insert the ignition key and start the engine, the LED will remain off, indicating no faults are found.
SPECIAL FUNCTION NOTE: 1. THE ALARM SYSTEM MUST BE DISSARMED PRIOR TO PROGRAMMING 2. ONLY GENUINE SUBARU TRANSPONDERS MUST BE USED WHEN PROGRAMMING KEYS.
SPECIAL FUNCTION PROGRAM KEYS PLEASE WAIT SECURITY CODE 1 SENT PROGRAM KEYS PLEASE WAIT SECURITY CODE 2 SENT PROGRAM KEYS PLEASE WAIT ERASING KEYS PROGRAM KEYS PLEASE WAIT STORING KEY 1 Note: If no more keys are required to be programmed press BACK. If more keys are to be programmed press ENTER and follow the on screen instructions.
22 SUZUKI
SUZUKI MANUAL CONTENTS PAGE APPLICATIONS 237 SPECIAL FUNCTIONS 238 7 22 APM115
APPLICATIONS VEHICLE AIMODEL YEAR CABLE WAGON-R ALL MODELS ADC110 VITARA ALL MODELS ADC128 GRAND VITARA ALL MODELS ADC128 ALTO ALL MODELS ADC128 SWIFT ALL MODELS ADC128 0r ADC131-B BALENO ALL MODELS ADC128 0r ADC131-B IGNIS ALL MODELS ADC128 LIANA ALL MODELS ADC128 CARRY 1.
SPECIAL FUNCTIONS KEY PROGRAMMING—ALL SYSTEMS DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS Select SPECIAL FUNCTIONS from menu. Select PROGRAM KEYS PRESS ENTER KEY DIAGNOSTIC MENU > PROGRAM KEYS The AD100 will automatically enter the security pin code and program the key in the ignition. PRESS ENTER KEY NOTE : If CODE ERROR is displayed then the access code is incorrect.
SPECIAL FUNCTIONS SWITCH IGNITION OFF PRESS ENTER ......... The AD100 will automatically enter the security pin code. NOTE : If CODE ERROR is displayed then the access code is incorrect. A series of dots will be displayed while the AD100 programs the key. After the key is programmed the complete screen will be displayed. PROCEDURE COMPLETE NOTE : Further keys can be added by repeating the above procedure by selecting PROGRAM KEYS.
23 TOYOTA LEXUS
TOYOTA & LEXUS MANUAL CONTENTS PAGE APPLICATIONS 242 GENERAL OPERATION 244 SPECIAL FUNCTIONS 256 FAULT CODES 262 TROUBLESHOOTING 263 7 23 APM124
APPLICATIONS MODEL 4Runner Camry Higlander LandCruiser MR2 Prius RAV4 Sequoia Sienna Solara 244 YEAR SYST TYPE Reset Imm System Add or Rewrite Keys Add or Rewrite Wireless Live Data Feed Fault Codes 2001 1 Y On Board On Board n/a Y 2002 1 Y On Board On Board n/a Y 2003 2 Y Y On Board Yes Y 2004 2 Y Y On Board Yes Y 2002 1 Y On Board On Board n/a Y 2003 1 or 2 Y On Board On Board n/a 2004 2 Y Y On Board Yes Y 2001 1 V6 On Board On Board n/a
APPLICATIONS MODEL ES300 GS300 IS300 GS430 LX470 YEAR SYSTEM TYPE Reset Imm System Add or Rewrite Keys Add or Rewrite Wireless Live Data Feed Read & Clear Faults 2002 1 Y On Board On Board n/a Y 2003 1 Y On Board On Board n/a Y 2002 1 Y On Board On Board n/a Y 2003 1 Y On Board On Board n/a Y 2004 1 Y On Board On Board n/a Y 2001 1 Y On Board On Board n/a Y 2002 1 Y On Board On Board n/a Y 2003 1 Y On Board On Board n/a Y 2004 1 Y On Boa
GENERAL OPERATION TOYOTA & LEXUS IMMOBILISER MANUAL KEY REGISTRATION The following list provides information about which models have the manual key registration, which is used when the Master key is available. These vehicles CANNOT be used with the AD100 or TCODE software to RESET the ECU.
GENERAL OPERATION TOYOTA IMMOBILISER RESET IMMOBILISER : (TYPE 1 & 2 IMMOBILISER) This function allows you to erase all keys and to Auto Learn the new key in the ignition lock at the time. This function is used when the customer has lost all their keys. PROGRAM KEYS : (TYPE 2 IMMOBILISER) This function allows you to add a Master or Valet key to the cars immobiliser system as long as you have an existing pre– programmed Master Key to start with.
GENERAL OPERATION LEXUS IMMOBILISER RESET IMMOBILISER : (TYPE 1 & 2 IMMOBILISER) This function allows you to erase all keys and to Auto Learn the new key in the ignition lock at the time. This function is used when the customer has lost all their keys. PROGRAM KEYS : (TYPE 2 IMMOBILISER) This function allows you to add a Master or Valet key to the cars immobiliser system as long as you have an existing pre– programmed Master Key to start with.
GENERAL OPERATION TOYOTA IMMOBILISER—TYPE 1 COMPATIBLE TRANSPONDER KEYS FOR THESE MODEL’S TOYOTA MASTER KEYS MODEL YEARS FACTORY PART NOTES 4 Runner 01-02 Camry 2002 Highlander 01-03 Land Cruiser 01-02 No Remote Land Cruiser 01-02 Remote Sequoia 01-02 Solara 02-03 TOYOTA IMMOBILISER—TYPE 2 COMPATIBLE TRANSPONDER KEYS FOR THESE MODEL’S 23 TOYOTA FACTORY MASTER KEYS MODEL YEARS 4 Runner 2004 Highlander 2004 Land Cruiser 03-04 Sequoia 2004 Solara 2004 FACTORY PART NOTES REM
GENERAL OPERATION TOYOTA IMMOBILISER—REMOTES—TYPE 2 COMPATIBLE TRANSPONDER KEYS FOR THESE MODEL’S TOYOTA FACTORY REMOTE MASTER KEYS MODEL Prius YEARS 2004 FACTORY PART NOTES Smart Access System Procedure 1. Open the driver’s door. 2. Within 5 seconds, put the remote into the remote opening and remove 2 times 3. Close the drivers door and open again 2 times 4. Put the remote in the remote opening and remove 5. Close the drivers door and open again 2 times 6.
GENERAL OPERATION TOYOTA IMMOBILISER— REMOTES—TYPE 2 MODEL YEARS ADD REMOTE ERASE REMOTE Land Cruiser 2001-2002 On Board Programming On Board Programming Land Cruiser 2003-2004 AD100 AD100 SYSTEM Not Applicable 2 ADD REMOTE Procedure 1. Make sure no keys are in the ignition lock and the drivers door is open and unlocked. 2. Put the key in the ignition and remove it. 3. Press the lock button for 1 second, press the unlock button for 1 second and repeat 5 times. 4.
GENERAL OPERATION LEXUS IMMOBILISER—TYPE 1 COMPATIBLE TRANSPONDER KEYS FOR THESE MODEL’S REMOTE MASTER KEYS MODEL YEARS PART No NOTES ES300 02-03 GS300 02-04 GS430 01-04 LX470 01-02 IS300 02-04 IS300 02-04 SEDAN IS300 02-04 Sort Cross FACTORY PART : FACTORY PART : 23 FACTORY PART : 252
GENERAL OPERATION LEXUS IMMOBILISER—TYPE 2 COMPATIBLE TRANSPONDER KEYS FOR THESE MODELS REMOTE MASTER KEYS MODEL YEARS PART No NOTES ES330 2004 GX470 03-04 LS430 01-04 LX470 03-04 RX330 2004 W.pwr Hatch RX330 2004 No pwr Hatch SC430 02-04 No Smart Access VALET KEYS MODEL YEARS ES330 2004 GX470 03-04 LS430 01-04 LX470 03-04 RX330 2004 SC430 02-04 PART No FACTORY PART : NOTE : IF YOU ARE USING THE WRONG TYPE OF KEY, THE PROCEDURES WILL NOT WORK.
GENERAL OPERATION LEXUS IMMOBILISER—TYPE 2 COMPATIBLE TRANSPONDER KEYS FOR THESE MODELS NOTE PROGRAMMING THIS TYPE OF KEY HEAD WILL ONLY START THE VEHICLE. YOU WILL NOT BE ABLE TO PROGRAM THE REMOTE BUTTONS. REMOTE KEYS MODEL YEARS TYPE PART No NOTES LS430 2004 MASTER With opt smart access LS430 2004 VALET With opt smart access 23 NOTE : IF YOU ARE USING THE WRONG TYPE OF KEY, THE PROCEDURES WILL NOT WORK. NO AFTERMARKET KEYS WILL WORK FOR THESE MODEL TYPES.
GENERAL OPERATION LEXUS IMMOBILISER—REMOTE CONTROLS MODELS YEAR ADD REMOTE ERASE REMOTE SYSTEM TYPE ES300 2002-2004 On Board On Board N/A ES330 2004 On Board On Board N/A GS300 2002-2004 AD100 AD100 3 GS430 2001-2004 AD100 AD100 3 GX470 2003-2004 AD100 AD100 2 IS300 2002-2004 AD100 AD100 3 LS430 2001-2003 AD100 AD100 1 LS430 2004(a) AD100 AD100 1 LS430 2004(b) Not supported on smart access at this time LX470 2001-2002 On Board On Board N/A LX470 2003-200
GENERAL OPERATION LEXUS IMMOBILISER—REMOTE CONTROL(On board) ADD REMOTE Procedure 1. Make sure no keys are in the ignition lock and the drivers door is open and unlocked. 2. Within 4-5 seconds put the key in the ignition and remove 2 times. 3. Close the drivers door and open 2 times. 4. Put the key in the ignition and remove. 5. Close the drivers door and open 2 times. 6. Put the key in the ignition and close all doors. 7. Turn the ignition ON for 1 second then OFF. 8. Remove the key from the ignition. 9.
GENERAL OPERATION SECURITY LIGHTS LX470 GX470 LX470 & LAND CRUISER SC430 ES330 LS430 GS430 23 MR2 257
SPECIAL FUNCTIONS RESET IMMOBILISER DIAGNOSTIC MENU RESET IMMOBILISER ADD MASTER KEY ADD VALET KEY ERASE KEYS RESET IMMOBILISER NOTE : This will cause ALL keys to be erased and the immobiliser to RESET itself. Do NOT be impatient. Some vehicles go past 16 minutes. If the timer goes past 35 Minutes, stop disconnect the AD100 and wait 20 seconds and try again.
SPECIAL FUNCTIONS ADD MASTER KEY SWITCH IGNITION OFF REMOVE MASTER KEYWITHIN 20 sec AND THEN PRESS ENTER TIME ELAPSED : 1 S Read carefully and follow the screen prompts.
SPECIAL FUNCTIONS ADD VALET KEY WARNING FOLLOW NEXT SCREENS QUICKLY & CAREFULLY PRESS ENTER KEY Read carefully and follow the screen prompts. ADD VALET KEY SWITCH IGNITION OFF REMOVE MASTER KEYWITHIN 20 sec AND THEN PRESS ENTER TIME ELAPSED : 1 S ADD MASTER KEY Read carefully and follow the screen prompts.
SPECIAL FUNCTIONS ERASE KEYS DIAGNOSTIC MENU RESET IMMOBILISER ADD MASTER KEY ADD VALET KEY ERASE KEYS ERASE KEYS WARNING FOLLOW NEXT SCREENS QUICKLY & CAREFULLY PRESS ENTER KEY ERASE KEYS SWITCH IGNITION OFF REMOVE MASTER KEYWITHIN 20 sec TIME ELAPSED : 1 S ERASE KEYS INSERT MASTER KEY SWITCH IGNITION ON PRESS ENTER KEY PLEASE WAIT TRYING TO COMMUNICATE 261 23
SPECIAL FUNCTIONS ADD REMOTE CONTROL DIAGNOSTIC MENU PROGRAM REMOTE ERASE REMOTES PROGRAM REMOTE SWITCH IGNITION ON UNLOC.DRV.DOOR OPEN DRIV.DOOR PRESS ENTER KEY PROGRAM REMOTE FOLLOW NEXT SCREENS QUICKLY & CAREFULLY COMPLETE OPERATION WITHIN 30 Sec AFTER PRESSING ENTER PROGRAM REMOTE PRESS LOCK & UNLOCK TOGETHER FOR 1 Sec WITHIN 3 Sec PRESS EITHER KEY FOR 1 Sec TIME ELAPSED : 0 S Press lock and unlock buttons together for 1 second and quickly press either lock or unlock button for 1 second.
SPECIAL FUNCTIONS ERASE REMOTE CONTROL DIAGNOSTIC MENU PROGRAM REMOTE ERASE REMOTES ERASE REMOTE SWITCH IGNITION ON UNLOC.DRV.DOOR OPEN DRIV.DOOR PRESS ENTER KEY ERASE REMOTES FOLLOW NEXT SCREENS QUICKLY & CAREFULLY COMPLETE OPERATION WITHIN 30 Sec AFTER PRESSING ENTER Press lock and unlock buttons together for 1 second and quickly press either lock or unlock button for 1 second. You must do this very fast.
FAULT CODES LIST OF KNOWN FAULT CODES B1242—WIRELESS DOOR LOCK TUNER CIRCUIT MALFUNCTION B2780—PUSH SWITCH/KEY UNLOCK WARNING SWITCH MALFUNCTION B2784—ANTENNA COIL OPEN CIRCUIT B2793—TRANSPONDER CHIP MALFUNCTION B2794—UNMATCHED ENCRYPTION CODE B2795—UNMATCHED KEY CODE B2796—NO COMMUNICATION IN IMMOBILISER SYSTEM B2797—COMMUNICATION MALFUNCTION NO 1 B2798—COMMUNICATION MALFUNCTION NO 2 B2799—ENGINE IMMOBILISER SYSTEM MALFUNCTION 23 264
TROUBLESHOOTING TROUBLESHOOTING—TOYOTA & LEXUS 1) The Security light can be in 2 different shapes, small RED circle next to the word security, or a RED light in the shape of a car. 2) Make sure you are using the correct key. 3) Learned Immobiliser Keys : Valet Key—when first inserted into the ignition lock the security light will stay on for 2 seconds and then stay off. Master Key—when inserted into the ignition the security light will NOT light up.
24 VW AUDI SEAT SKODA
VW-AUDI-SEAT-SKODA MANUAL CONTENTS PAGE APPLICATIONS 266 GENERAL OPERATION 267 FAULT CODE OPERATION 268 SPECIAL FUNCTIONS 270 TIPS & HINTS 275 7 24 APM101
APPLICATIONS VEHICLE IMM IMM + INSTR YEAR CABLE AUDI A3/A4 Y A6 Y A6 A8 Y Y Y A8 Y ALL MODELS ADC110 < 96 ADC112 > 96 ADC110 < 96 ADC112 > 96 ADC110 COUPE Y < 97 ADC112 80/90 Y < 97 ADC112 ALL MODELS ADC110 ALL MODELS ADC110 ALL MODELS ADC110 TT Y SEAT ALHAMBRA Y AROSA Y ALTEA Y ALL MODELS ADC110 CORDOBA Y ALL MODELS ADC110 IBIZA Y ALL MODELS ADC110 INCA Y ALL MODELS ADC110 LEON Y ALL MODELS ADC110 TOLEDO Y Y < 97 ADC112 TOLEDO Y Y > 98
GENERAL OPERATION SYSTEM DESCRIPTION The VAG group immobiliser system consists of an immobiliser ECU which controls the recognition of keys and the Engine Management ECU system. The Immobiliser ECU enables up to 8 keys to be programmed and are recognised via the transponder aerial mounted around the Ignition lock. If the keys are lost or a replacement Engine Management ECU is fitted then the transponder keys will need programming so that the ECU memories recognise the codes.
FAULT CODE OPERATION READING FAULT CODES DIAGNOSTIC MENU ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS Using the UP and DOWN keys select the FAULT CODES selection. Then press the ENTER key. PRESS ENTER KEY DIAGNOSTIC MENU READ FAULT CODES CLEAR FAULT CODES Using the UP and DOWN keys select the READ FAULT CODES selection. Then press the ENTER key. PRESS ENTER KEY Depending on how many fault codes are set, will depend on how many screens are displayed, however two examples are shown below.
FAULT CODE OPERATION DIAGNOSTIC MENU READ FAULT CODES CLEAR FAULT CODES Using the UP and DOWN keys select the CLEAR FAULT CODES selection. Then press the ENTER key. PRESS ENTER KEY CLEAR FAULT CODES PROCEDURE COMPLETE If all the fault codes have been cleared the screen will display PROCEDURE COMPLETE.
SPECIAL FUNCTIONS PROGRAMMING KEYS ECU IDENTIFICATION SYSTEM 1 > SYSTEM 2 PRESS ENTER KEY PLEASE WAIT TRYING TO COMMUNICATE ECU IDENTIFICATION IMMO-IDENTNR : VWZ720W049 5589 Using the UP and DOWN arrows select the correct vehicle system as outlined in the previous section. Then press the ENTER key. The AD100 will try to establish communications with the Immobiliser ECU. If it is unsuccessful try the other system as outlined in the previous section.
SPECIAL FUNCTIONS SECURITY CODE ____ SECURITY CODE 1234 IS THIS CORRECT PLEASE WAIT TRYING TO COMMUNICATE Enter the 4 digit security code. NOTE : You are allowed 3 attempts to enter the correct code. If the code is entered incorrectly 3 times the ECU will lock out communication for 35 minutes. To reset the ECU the ignition must be left on for 35 minutes without any interruptions. If code is correct press the ENTER key. If code is entered incorrectly then press the BACK key to reset the code.
SPECIAL FUNCTIONS PROGRAMMING ADDITIONAL KEYS (Contd) Procedure 1. The Key already in the ignition will now be programmed, ie. Key 1 2. Remove Key 1. 3. Insert Key 2 and turn ignition on. for 2 seconds. Then remove key 4. Insert Key 3 and turn ignition on. for 2 seconds. Then remove key 5. Repeat for all keys. 6. Try all the keys to ensure they work. 7. Check for any fault codes that may have been set, and clear the memory. NOTE : The maximum number of keys that can be programmed is 8.
SPECIAL FUNCTIONS ECU CODING VEHICLE SELECTION > PROGRAM ECU Select PROGRAM ECU from the vehicle selection menu. PRESS ENTER KEY VEHICLE SELECTION > SYSTEM 1 > SYSTEM 2 Select the required system.
SPECIAL FUNCTIONS SECURITY CODE 1234 IS THIS CORRECT OK=ENTER CLEAR=BACK RECODE ECU/IMMO SUCCESSFUL PLEASE TURN OFF IGNITION FOR 15 SECS You will be asked to enter the 4 digit security code to enable Program ECU. SYSTEM 1 Goes straight into learning process as no vehicle selection needed. User will see text “READING ECU DATA” and “SAVING ECU DATA” FLASH on screen as process is carried out. If successful this screen is displayed.
TIPS & HINTS VW-AUDI-SEAT-SKODA 1. 2. When reading Pin codes from vehicle memory, if loss of communications is experienced, try reading fault codes, then clearing fault codes then read the pin code. If when programming keys, the AD100 displays the following :— KEYS PROGRAMMED : 136 This means the incorrect PIN CODE has been entered.
TIPS & HINTS VW-AUDI-SEAT-SKODA Damage to AD100 Some cases of internal damage to the AD100 have been traced to a radio wiring fault on VAG vehicles. VAG cars from 1997 onwards have the ability to code/fault code read the radio and therefore the diagnostic wire or K line that is used to connect all of the control units on the car (including the immobiliser) goes to the radio.
