COLOUR TELEVISION INSTRUCTION MANUAL MODEL No.
Contents Important safeguards 1 Before Operation 2 Connecting external equipment 3 Identification of Controls 5 Daily use 6 Menus 8 Teletext 14 Specifications 16
Important safeguards WATER AND MOISTURE Never install the set in the following places : In a wet basement, bathroom. Do not place any container with liquid on the set. HEAT Never place the set near heat sources. VENTILATION Do not cover the ventilation openings in the cabinet and never place the set in a confined space such as a bookcase or built-in unless proper ventilation is provided. Leave a minimum 10cm gap all around the unit.
Before Operation Battery options INSERTING BATTERIES INTO THE REMOTE CONTROL UNIT Insert the batteries (two 1.5V, type AAA) MAINS CONNECTION Plug the mains cable into the power socket with 230V/50Hz AC. AERIAL CONNECTION When using an outdoor aerial, it is usually connected to the set by means of 75 ohm. SWITCHING ON AND OFF Switching on Switch the set on with the MAIN POWER button(ON/OFF), and then CH UP or DOWN button on the front of the set.
Connecting external equipment TV AND AV Use the TV/AV( ) button on the remote control or on the front of the set to select one of the three options. Whenever the TV/AV ( ) button is pressed, the on-screen display will be changed as shown: AV S-VHS TV SCART JACK AV (BACK) This is used to connect a VCR, a Camcorder, a S-VHS VCR, a PERI-TV decoder or a video game console. In most cases, the set changes automatically to AV when the VCR connected is in display mode.
RCA JACK AV (FRONT) Connect the AV (Audio/Video) socket with an appropriate cable to the corresponding socket of the external equipment. Select AV mode by pressing the TV/AV( Press the TV/AV( the TV mode. ) button. ) button to return to NOTE: If two apparatus are connected, one to the front AV Jack and the second to the rear SCART Jack, you can play only one apparatus. The second one must be switched off. OR HEADPHONE JACK Insert the headphone plug(3,5mm) into the headphone socket.
Identification of Controls Back Aerial Terminal Scart Socket REMOTE CONTROL TV MODE TELETEXT mode 1. POWER 1. POWER 2. NUMBER 0-9 2. NUMBER 0-9 3. NORMAL 3. INDEX 4. AV 4. MIX 5. PR(CUROSR) UP 5. PAGE UP 6. VOLUME UP(CURSOR RIGHT) 6. SUBPAGE 7. MENU 7. MENU 8. PR(CURSOR) DOWN 8. PAGE DOWN 9. VOLUME DOWN (CURSOR LEFT) 9. HOLD 10. MUTE 10. MUTE 11. RECALL 11. REVEAL 12. SLEEP 12. SIZE 13. not used 13. CANCEAL 14. MOVE (Edit mode only) 14. GREEN KEY 15.
DAILY USE PROGRAMME SELECTION Direct selection Use remote control NUMBER 0…9 buttons. For two digits programme numbers, press the button for the second digit within 2.5 seconds. Up/Down moves Use PR UP/DOWN buttons of the remote control unit or on the front of the set. SOUND CONTROL Volume adjustment Use VOLUME UP/DOWN buttons of the remote control unit or on the front of the set. Mute Get sound off by pressing the remote control MUTE ( ) button. Then, logo ( ) is displayed.
SLEEP FUNCTION The sleep function will switch the television to stand-by after a set period of time. Pressing repetitively the remote control SLEEP button, you can enter one of the following settings : OFF > 30 min > 60 min > 90 min > 120 min > OFF The remaining time before TV turn-off is displayed on programme status. PROGRAMME STATUS DISPLAY Accessed by the Remote Control RECALL button.
Menus MAIN MENU All menus are removed within 25 seconds if you don’t press any button. Direct selection Press remote control MENU button to display main menu. Then, you have the choice between several submenus. PICTURE FEATURES INSTALL If you want to cancel immediately main menu, press MENU button once more. To select one of the sub-menus, use remote control CURSOR buttons UP, DOWN, LEFT, RIGHT. To enter the selected sub-menu, press remote control NORMAL/OK button .
PICTURE MENU Enter PICTURE in the main menu. You can select each function with the UP/DOWN buttons. Use the LEFT/RIGHT buttons to adjust each function. Explanation for each function will be displayed in the lower screen whenever you select the function. (Tint control for AV NTSC only) PICTURE BRIGHT. CONTRAST COLOUR SHARP. TINT FEATURES MENU LANGUAGE Language selection. FEATURES CHILD LOCK Child lock prevent the use of the TV set without remote control unit.
INSTALL MENU ATSS Automatic Tuning and Sorting System. EDIT Programme list edition. SYSTEM TV system selection. CHANNEL Channel number. FREQ Channel Frequency. NAME Channel name. PROGRAM Programme number. STORE TO Programme storage number. INSTALL ATSS EDIT SYSTEM CHANNEL FREQ NAME PROGRAM STORE TO Others EURO - -211.25 ----01 01 EDIT MENU PR Programme number. NAME Station name. CH Channel number. Skip : programme skipped.
AUTOMATIC TUNING SYSTEM Automatic Tuning and Sorting System Select "ATSS" function and adjust to required country. Press remote control "NORMAL/OK" button more than 3 seconds to start the automatic tuning. When automatic tuning is finished, recorded programmes are displayed on screen. Note for satellite receiver users : Before starting ATSS, connect your equipment to the TV set, turn it ON and tune SKY NEWS. PROGRAMME LIST EDITION Using the Edit Menu, you can easily modify the programme listing.
Channels order changing Select the programme to move using remote control CURSOR UP/ DOWN buttons. Press the remote control NORMAL/OK button : the programme appears on red and can be moved to another place using remote control CURSOR UP/ DOWN buttons. When required position is reached, confirm this new position pressing the remote control NORMAL/OK button. Then, the programme appears again on green.
Fine Tuning If you are unable to get a good picture or sound because of a poor broadcasting signal, it is possible to fine tune a signal. Select channel frequency ("FREQ.") function. Press and release the remote control CURSOR RIGHT/LEFT buttons to fine tune a signal. Enter station name Select "NAME" function. Use the CURSOR RIGHT/LEFT buttons to select the character (letter) you want to modify. To modify this letter press the CURSOR UP/DOWN buttons until the desired letter is displayed.
Teletext SWITCHING TELETEXT ON/OFF Press the TELETEXT button ( ). The index page viewed last will appear. Press the TELETEXT button to return to the TV mode. Note that TELETEXT on this TV set is operated to Level 1.5. COLOUR BUTTONS IN TOP/FLOF TELETEXT Red, green, yellow and cyan fields are shown at the bottom of the screen. If TOP or FLOF teletext (FASTEXT) is transmitted by the station, press the corresponding colour button on the remote control unit, you can select the desired page easily.
WATCHING TELEVISION DURING TELETEXT MODE Some pages are continually updated, for example, stock market reports, sports announcements, and the latest news. If you want to watch television and stay informed at the same time, press the CANCEL ( ) button. The regular programme is still visible and the teletext programme number appears at the top of the screen. Pressing the CANCEL button again, the teletext page appears with the updated information.
SPECIFICATIONS TV Standard PAL/SECAM-B/G, D/K, H, NTSC(AV ONLY) SECAM-L/L’(OPTION), PAL-I(OPTION) Main Voltage 230V~, 50Hz Power Consumption 14” : 39W approx 20” : 42W approx 21” : 45W approx Sound Output Power 2.5W (60% MOD. at 1KHz THD. 10%) Dimensions(WxHxD) &Weight 14” : 366 x 338 x 376mm, 9.5Kg 20” : 496 x 446 x 464mm, 18.0Kg 21” : 516 x 466.5 x 476mm, 20.0Kg Owing to our policy of continuous product improvement, specifications may change.
