PLASMA TELEVISION USER MANUAL DTS-42 Proper use guarantees product life. Before using the product, be advised that you read this user manual well and try to operate it.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is lntended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat. 9.
Features • 42” VGA wide Plasma Panel • Built in Analog Tuner PDP has the analog tuner inside for watching terrestrial broadcasting without the need to purchase a separate broadcasting receiver. • DVD Direct Connection / Outstanding Picture Quality via a Digital Broadcast Receiver A DVD can be directly connected to the unit so that you can view clear digital images. You can enjoy even higher quality images by connecting a digital broadcasting receiver with which digital broadcasts can be viewed.
F C C R F I N T E R F E R E N C E S TAT E M E N T NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications.
Safety Precautions Power Always obey all safety messages. • All the safety and operating instructions should be read before the product is operated. If anything strange happens, unplug this product from the wall outlet. • Do not disassemble or replace any parts of the TV. Refer to a qualified service personnel for repair. During a lightning storm, or when it is left unattended and unused for a long period of time, unplug it from the wall outlet.
During Use The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not open the cover (or back) because high voltage is present within the TV enclosure. Never push any kind of objects into this product through openings at the back of TV. It may cause electric shock. It may cause fire or electric shock. Do not allow children to play or hang on the TV. Do not place a candle or lighted cigarette on the TV.
Safety Precautions Power Always obey all safety messages. • All the safety and operating instructions should be read before the product is operated. CAUTION You can be injured, or this product or any other of your property can be damaged if you don’t follow instructions. When moving your TV, remove the power plug, antenna, and cables, and be sure to move it by using two people.. Do not touch the power plug with wet hands when plugging or unplugging it into the wall socket.
During Use Do not wipe the TV using a cloth damped with chemicals (benzene, thinner, etc.). Do not place heavy objects or heat sources on the power cord. TV appearance may be marred. (Unplug the power plug and wipe with soft cloth.) It may damage the power cord, causing fire or electric shock. Do not place any object or cover on the TV. When watching the TV, the distance between the TV screen and your eye should be as 5~7 times as the diagonal distance of the TV.
Checking Accessories Note Check to be sure that the following items are packed with your Plasma panel. Supplied Accessories Remote Control POWE 1 UNIT Ferrite Core 2UNITS R CAT V SAT EO/ VID DVD TV DIS Y PLA TV/ MU VID LTIM EDI A EO ZOO M + ZOO M - CH V O L U SC RE EN SIZE MEN V O L PR EV CH CH TE MU W SLO F.R/ PRE N TIO CAP W SLO F.
Note Optional Accessories Speakers The following items are optional accessories. Refer purchasing optional accessories from Daewoo Electronics Local retailer or the retailer from where you purchased the unit. DTS-42SP - Speaker Main Unit Dimension : 100(W) x 628(H) x 83(D) mm 39.37(W) x 24.72(H) x 3.27(D) inch - Dimension Including Speaker Stand : 170(W) x 729(H) x 194(D) mm 6.69(W) x 28.7(H) x 7.64(D) inch - Audio Amplifier : 10W + 10W - Impedance : 8Ω - Weight : 6.4kg(14.
CONTENTS PREPARATION 6 • 10 • 14 • 15 • 16 • Safety Precautions Checking Accessories Panel Controls Remote control Remote Control Setup CONNECTION 17 • 20 • 22 • 28 • 30 • 32 • 34 • 36 • 38 • 40 • 42 • Antenna Connection To Watch TV Channel Setup Watching Digital Broadcasts Watching Cable Broadcasts Watching Satellite Broadcasts Watching a DVD Image Watching a VCR Image Watching a Camcorder/Game Console Image Connecting PC(15Pin D-Sub) Connecting PC(DVI) APPLICATION 45 • 46 • 48 • 50 • 52 • 54 • 55 • 5
Panel Controls Front Panel, Back Panel, Remote Control having same names on Plasma television and the remote control would function in exactly * Items the same way. Front ON/OFF STAND BY/OPERATE • Power control sensor • Power Standby: Red - Standby Select when adjusting volume or select/adjust “MENU.
Remote Control Note • Use two “AAA” batteries. • Be sure to use replacement batteries of the same type as the original ones. • The life of a battery depends on how much it has been used. ) indicates the page in which * The number in ( the function of each button is explained in detail. POWER Power button 20 TV/VIDEO(DVD)/SAT/CATV VIDEO/ DVD TV SAT Pressing the Power button of the TV allows the Display to be standby. (Red light is shown in the Remote Control Sensor.
Remote Control Setup Remote control supporting the multi brand devices. - The remote control provided is designed to operate the Daewoo PDP set. - However, using the remote control, you can control the Cable Converter, VCR , DVD and Satellite Broadcasting Receiver of other brands after setting up the remote control. Notices: - All the preset codes are erased when replacing the battery. In this case, you must set the remote control again.
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. 2. Connect the combining adapter to the antenna input at the back of the TV set. WHEN USING THE COMBINING ADAPTER You may obtain the combining adapter at your closest Service Center.
CTV Antenna Connection TV Antenna installation may be found in most. When a coaxial cable is used Plug the coaxial cable to the antenna socket, and fix it firmly. It is recommended to use the provided coaxial cable.
Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses Single Antenna Connection. VHF Antenna UHF Antenna ANT/CABLE 1 Separate Antenna Connection.
To Watch TV To Watch TV - The buttons on the keypad in the PDP unit, which have the same name as those on the remote controller, perform the same function as the remote controller. Press the “ON/OFF” button of the PDP unit. POWER •Power button of the remote control and the keypad on the PDP unit would be operated only when the "AC Power" of the PDP unit is supplied. Otherwise, neither the remote controller nor keypad of the PDP unit can turn on the PDP.
• Press the “ON/OFF” button of the PDP set. • The main power lamp turns on in red color. • Press the "POWER" button of the remote control or any button in the keypad of the main body. • The LED of the PDP set turns on in “green” color and the set turns on. ON/OFF POWER 2 Select Channel. ZO - M O + ZO O CH M V O L CH 09 MONO PM 12 : 00 No Ratings E PR SI ZE MENU V CH CH E RE SC Adjust volume.
Channel Setup Automatic Channel Memory - This is the function for the TV to memorize the broadcasting channels. If the Auto Setup is done, you can simply find out channels with “ CH ” buttons and so need not to select channels by pressing each channel number. PO W TV VID E DVDO/ SAT ER CAT V DIS PLA Y TV/V IDE O MU LTIM EDIA CH OM ZO + OM ZO V O L ME NU PRE VC V O L H E SIZ EN SCRE CH MU TE F.R /SL OW PLA Y REC STO 1 Press the “Menu” button.
3 Select the [Auto Search]. • Select the “Auto Search” with the “ CH ” button. ZO - M O Ch Mode Air + ZO O CH M Picture V O L V O L MENU Sound Channel 42 Memory Add Fine Tune 0 N E PR V SI ZE Auto Search Screen CH CH E RE SC Features Channel Move 4 MENU Exit Press the “VOL ” button. + V O L N E PR SI ZE MENU V • By pressing the “VOL ” button automatically searches OnAir Channel as in the right.
Additional Channel Memory Additional Channel Memory 1 Select the Channel to memorize. • Select the Channel by pressing the number button. Ex) “13” channel • This is method for additionally memorizing channels not memorized due to weak broadcasting signal. • This function is available even in the [Menu] - [Channel] [ADD/ERASE]. CH 13 MONO PM 12 : 00 No Ratings POWER VIDEO/ DVD TV SAT 2 CATV Press the “ADD/ERASE” button.
Erase of Memorized Channel 1 Select the Channel to erase. M ZO - M O + ZO O CH V O L V O L N E PR V SI ZE MENU • Select the Channel to erase with the “ CH ” button. • You may select the Channel by pressing the number button. Ex) “13” channel CH CH 2 E RE SC Erase of Memorized Channel • This is function to erase unnecessary memorized channel. • This function is available even in the [Menu] - [Channel] [ADD/ERASE]. Press the “ADD/ERASE” button.
Fine Tune - If you are unable to get a good picture or sound because of a poor signal reception, it is possible to adjust it with the Fine Tune feature.. PO W TV VID E DVDO/ SAT ER CAT V DIS PLA Y TV/V IDE O MU LTIM EDIA CH OM ZO + OM ZO V O L ME NU PRE VC V O L H E SIZ EN SCRE CH MU TE F.R /SL OW PLA Y CAP F.
2 Select “Air/Cable” in [Ch Mode]. ZO - M O + V O L Sound Air Channel 42 Memory Add Fine Tune 0 Auto Search Screen N CH CH E RE SC Features Channel Move CH M ZO - M O 3 Adjust MENU Exit Select Fine Tune + V O L V O L MENU E PR V SI ZE E PR V SI ZE MENU Ch Mode Picture • Select [Fine Tune] by using the “ CH ” button. • Until the screen becomes best condition, adjust the screen by pressing the “ VOL ” button.
Watching Digital Broadcasts Watching Digital Broadcasts • To watch digital broadcasts: - Purchase a separate digital Broadcasting Receiver(SET-TOP BOX) - Connect the PDP to a Digital Broadcasting Receiver as shown right. 1 Connect a Digital Broadcasting Receiver to the PDP • Prepare supplied A/V cables. • Connect the cables from the Digital TV Receiver output terminal to the PDP(Component 1, 2) input terminal. • When connecting the cables, be sure to match the cable colors.
3 Input Select MULTIMEDIA • Select [Component 1 or Component 2] by pressing the “Multimedia” button of the Remote Control or the "INPUT SELECT" Key in KeyPad of the pdp set. • Each time you press the “Multimedia” button, different input modes appear. The sequence is as follows: 4 Component1 Component2 DVI PC Select a Desired Channel and Function • Select a desired channel and function by using the Remote Control of Digital Broadcasting Receiver.
Watching Cable Broadcasts Watching Cable Broadcasts • To watch cable broadcasts, subscribe to your local Cable TV Broadcasting, and then connect a cable Broadcasting Receiver TV to the PDP as shown right. 1 Connect a Cable Broadcasting Receiver to the PDP. • Prepare the A/V cable. • Connect the receiver(Output) to PDP(Video Input) as shown below. • When connecting to an external AV source, be sure to match the colors.
3 Input Select TV/VIDEO • Select [Video 1 or Video 2] by pressing the TV/VIDEO button of the Remote Control or the "INPUT SELECT" Key in KeyPad of the pdp set. • Each time you press the “TV/VIDEO” button, different input modes appear. The sequence is as follows: Video1 Video2 TV 4 Select a Desired Channel and Function • Select a desired channel and function by using the Remote Control of the Cable Broadcasting Receiver.
Watching Satellite Broadcasts Watching Satellite Broadcasts • To watch satellite broadcasting, subscribe to Digital Satellite Broadcasting, then connect satellite Broadcasting Receiver to the PDP as shown right. 1 Connect a Satellite Broadcasting Receiver to the PDP. • Prepare the A/V cable. • Connect the receiver(Output) to PDP(Video Input) as shown below. • When connecting to an external AV source, be sure to match the colors.
3 Input Select TV/VIDEO • Select [Video 1 or Video 2] by pressing the TV/VIDEO button of the Remote Control or the "INPUT SELECT" Key in KeyPad of the pdp set. • Each time you press “TV/VIDEO” button, a different input mode appears. The sequence is as follows: Video1 Video2 TV 4 Select a Desired Channel and Function • Select a desired channel and function by using the Remote Control of the Satellite Broadcasting Receiver.
Watching a DVD Image Watching a DVD Image • Component Input is set to 480i and 480p mode. • Connect the cable from the DVD Video Output (Y, Pb/Cb, Pr/Cr) to the Component Input at the back of PDP, and connect the cable from DVD Audio output (Left, Right) to the Audio Input at the back of PDP. 1 Connect a DVD Player to the PDP. • Prepare the AV cable. • Connect the DVD(Output) to the PDP(Component or Video Input) as shown below. • When connecting to an external AV source, be sure to match the colors.
3 Input Select MULTIMEDIA TV/VIDEO • Select [Component 1 or Component 2, Video1, Video2] by pressing the “MULTIMEDIA” or “TV/VIDEO” button of the Remote Control or the "INPUT SELECT" Key in KeyPad of the PDP set. • Each time you press the “MULTIMEDIA” or “TV/VIDEO” button, a different input mode appears.
Watching a VCR Image Watching a VCR Image 1 Connect a VCR to the PDP. • Prepare the AV cable. • Connect the Video(Output) to PDP(Video Input) as shown below. • Video can use either the video terminal or the S-video terminal. POWER VIDEO/ DVD TV SAT CATV DISPLAY TV/VIDEO MULTIMEDIA ZO - Video/Audio + V O L V O L N E PR SI ZE MENU V S-Video M O ZO O CH M E RE SC CH CH MUTE F.R/SLOW PLAY REC STOP CAPTION F.
3 Input Select TV/VIDEO • Select [Video 1 or Video 2] by pressing the “TV/VIDEO” button of Remote Control or the "INPUT SELECT" Key in KeyPad of the pdp set. • Each time you press the “TV/VIDEO” button, a different input mode appears. The sequence is as follows: Video1 Video2 TV 4 Select a Desired Title and Function • Select a desired title and function by using the Remote Control of the VCR. NOTES: 1) When connecting a Video, the S-Video terminal provides a better image than the Video terminal.
Watching a Camcorder/Game Console Image Watching a Camcorder/Game Console Image • Enjoy images recorded by camcorder or the game console after connecting to the PDP. 1 Connect a Camcorder/Game Console to the PDP. • Prepare the AV cable. • Connect the Video(Output) to the PDP(Video Input) as shown below. • When connecting to an external AV source, be sure to match the colors.
3 Input Select TV/VIDEO • Select [Video 1 or Video 2] by pressing the “TV/VIDEO” button of the Remote Control or the "INPUT SELECT" Key in KeyPad of the pdp set. • Each time you press the “TV/VIDEO” button, a different input mode appears. The sequence is as follows: Video1 Video2 TV 4 Select Function • Select the Function by using the Remote Control of Camcorder or Game Console. NOTES: 1) When connecting a Video, the S-Video terminal provides a better image than the Video terminal.
Connecting PC(15pin D-sub) Connecting PC • This product supports resolution of VGA, SVGA, XGA, and SXGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of PC. 1 Before connecting to the PDP, set the resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen of the PC. • Choose the SETTINGS tab in the DISPLAY Menu. • In the SETTINGS Menu, select 640 x 480 or 800 x 600. 2 Connect the PC to the PDP.
3 Press the Power Buttons. • Turn on the PDP and the PC. 4 5 Input Select MULTIMEDIA • Select [PC] by pressing the “MULTIMEDIA” button of the Remote Control or PDP unit. • Each time you press the “MULTIMEDIA” button, a different input mode appears. The sequence is as follows: Component1 Component2 DVI PC Enjoy Dynamic Ultra Screen TV by Using PC’s Keyboard or Mouse. NOTES: 1) The resolution of the PC TV is best at 640 x 480 (VGA).
Connecting PC(DVI) Connecting PC • This product supports resolution of VGA, SVGA, XGA, SXGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of PC. • This product is supported by Plug and Play only at DVI. 1 Before connecting to the PDP, set the resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen of the PC. • Choose the SETTINGS tab in the DISPLAY Menu. • In the SETTINGS Menu, select 640 x 480 or 800 x 600. 2 Connect the PC to the PDP.
3 Press the Power Buttons. • Turn on the PDP and the PC. 4 5 Input Select MULTIMEDIA • Select [DVI] by pressing the “MULTIMEDIA” button of the Remote Control or PDP unit. • Each time you press the “MULTIMEDIA” button, a different input mode appears. The sequence is as follows: Component1 Component2 DVI PC Enjoy Dynamic Ultra Screen TV by Using PC’s Keyboard or Mouse. NOTES: 1) The resolution of the PC monitor is best at 640 x 480 (VGA).
PC and DVI Input Resolution Available in PDP • Depending on graphic card, problems like no signal detected or line noises can happen. If these problems happen, contact the graphic card company for help. Resolution 640x400 H Freq. (KHz) 37.861 V Freq. (Hz) 85.080 Remark VESA DVI PC O 31.469 59.940 DOS O O 37.861 72.809 VESA O O 37.500 75.000 VESA O O 43.269 85.061 VESA O O 31.469 70.087 IBM O O 37.927 85.039 VESA 35.156 56.250 VESA O O 37.879 60.317 VESA O O 48.
Selecting Picture Mode Each Press of the Button Will Select One of Four Picture Modes. PICTURE MODE Normal * Normal : Cinema User For a highly defined image in a normally bright room For a clear-cut image emphasizing high contrast for sports viewing For a movie Allows the user to customise settings as desired. TV/VIDEO • After selecting a desired Picture mode, the menu on the screen will disappear. • Normal, Dynamic, and Cinema Modes are factory preset values.
Customizing Picture 1 Press the MENU Button. • The MENU shown below will display on the screen. CH M ZO - M O + ZO O Normal Mode • You can adjust the color tone and brightness to your preference. V O L V O L E PR V Picture SI ZE MENU Sound Brightness 32 Contrast 48 Color 32 Tint 32 N Customizing Picture E RE SC CH CH Screen Sharpness 32 Color Temp.
• While you are in [Picture Mode – User], press the “ buttons to select a specific adjustment item. ZO - V O L V O L ” N E PR CH CH User Mode Picture SI ZE MENU V CH + ZO O CH M M O 4 Select User Mode Adjustments E RE SC Sound Screen Brightness 30 Contrast 60 Color 40 Tint 32 Sharpness Color Temp. 48 Normal Features Channel Move 5 Adjust MENU Exit Picture Condition Adjustments • Press the “ VOL ” buttons to adjust the picture at your preference.
Adjusting Screen Size Adjusting Screen Size N SI ZE • You can adjust screen size or aspect ratio as desired. 1 Press the “SCREEN SIZE” Button. E RE SC • Each time you press the “SCREEN SIZE” button on the Remote Control, a different “SCREEN SIZE” appears. The sequence used is as follows: • The current screen size will be displayed on the screen.
ZO - M O M + V O L N E PR SI ZE Sound E RE SC CH CH Normal Mode Picture V O L MENU V Adjusting from MENU Screen • Press the [MENU] button on the Remote Control. CH ZO O 1 Press the MENU Button. Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness 32 Color Temp.
Adjusting Screen Size(PC, DVI) • The MENU screen as shown below will appear. M ZO - + ZO O CH Normal Mode V O L V O L Sound N V Picture SI ZE MENU E PR • You can adjust the screen position and size as desired. 1 Press the MENU Button. M O Adjusting Screen Position and Size E RE SC CH CH Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness Color Temp.
3 Press the Volume “ VOL ” button. ZO - M O + ZO O CH M V O L V O L N E PR V SI ZE MENU • Press the Volume “ VOL ” button to enter the sub menu of [Screen]. • While you are in [Screen] mode, press the “ CH ” button to select a desired item, and then, adjust the value by pressing the “ VOL ”. CH CH E RE SC Picture Sound Screen H. Size 32 V. Size 32 H. Position 32 V.
Enlarging Screen Size ZO M O + • You can view enlarged size of the screen with this function 1 Press the “ZOOM+” Button. ZO O Enlarging Screen Size M • Press the “ZOOM+” button to show currently selected screen size. • Each time you press the “ZOOM+” button, the screen size will increase stepwise in 0 ~ 20 scale. • To reduce the screen size, press the “ZOOM-” button.
• While you are in the ‘Zoom’ mode, press the “ CH ” and “ VOL ” buttons to move screen stepwise up/down and left/right, respectively. CH M ZO - M O + ZO O V O L V O L E PR V SI ZE MENU N 2 Move the Screen Position. CH CH E RE SC Zoom 6 NOTES: 1) When the screen is enlarged, the pixel of the screen can become thick and dim. 2) When only subtitle of zoom level remains, you can scroll the image. If subtitle of zoom level disappears, press zoom key, and scroll the image.
Watching a STILL Image Watching a Still Image 1 Press the “STILL” Button. • If you wish to freeze a picture, press the “STILL” button. You can still hear the sound. • Press “STILL” button to cancel the “STILL” function. • To view the enlarged images, press the “ZOOM+” button. STILL • You can view still images with this function. However, displaying the same images such as still images for a long time may cause image sticking.
Adjusting Auto Sound Mode 1 Select "SOUND MODE". Adjusting Auto Sound Mode • Press the "SOUND MODE" on the Remote Control. • Current sound mode will be displayed. SOUND MODE • Enjoy various sound modes by selecting your favorite Sound Mode depending on the kinds of moving pictures. POWER 2 Every Press of the Button Changes Modes. VIDEO/ DVD TV SAT CATV • Each time you press the button, a different sound mode appears.
Customizing Sound Mode 1 Press the MENU Button. • The MENU Screen as below will be displayed. CH + • This feature allows the user to adjust at his preference. M ZO - M O ZO O V O L Sound SI ZE E PR V E RE SC CH CH Normal Mode Picture V O L MENU N Customizing Sound Mode Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness Color Temp.
• Select [Effect] by pressing the “ CH ” buttons, then select ON/OFF by pressing the “ VOL ” button. • [Effect]: Used to emphasize stereo effect. CH M ZO - M O + ZO O V O L V O L E PR V SI ZE MENU Picture N 4 Select the Effect Mode. E RE SC CH CH Sound Screen Features Balance Effect MTS AVC Mode 120Hz 500Hz 1.5kHz 5kHz 10kHz 0 Off Mono Off Normal 0 0 0 0 0 Channel Adjust Move Exit • Select the Sound Mode by pressing the “ CH then adjust it by pressing the “ VOL ” button.
Selecting INPUT SIGNAL POW ER INPUT SIGNAL TV • Used to select INPUT signal of external device connected to the PDP. VIDE DVDO/ SAT DISP LAY TV/V IDEO MUL TIME DIA OM ZO CH + OM ZO V O L MEN U PRE V O L H E VC CH MUT E F.R/S LOW REC PLAY IZ NS EE SCR CAP T F.F/S ION LOW STO P PAU SE PRE V O PEN/C LOSE NEX PICT T MODURE SO E U MODND E STIL L MTS 1 SL Press the INPUT SELECT Button.
• “TV/VIDEO” button Video1 Video2 TV • “MULTIMEDIA” button Component1 Component2 DVI PC Component 1 1920 x 1080 NOTES: 1) If an external device is not connected or INPUT signal is not applied, Warning Message (“No Signal”) would be displayed. 2) In this case, check if external device is connected and/or terminal connection is properly done. 3) Also, you can select input using [INPUT SELECT] button in the keypad of the pdp set.
Checking the Current Input Signal Checking the Current Input Signal • Used to check the INPUT signal mode, resolution, frequency(video only), etc. of the current screen. 1 Press the “DISPLAY” Button. • Press the “DISPLAY” button on the Remote Control. DISPLAY Component 1 1920 x 1080 POWER VIDEO/ DVD TV SAT CATV 1. If you watch Component, PC or DVI : DISPLAY TV/VIDEO MULTIMEDIA Component 1 1920 x 1080 Displays which input terminal is used, and indicates the input signal mode.
MENU Background, Language and Key pad Lock Settings 1 Menu Background and Language Settings Press the MENU Button. • The MENU screen will be displayed as below. ZO - M O Picture V O L V O L MENU N E PR SI ZE Sound V E RE SC CH CH Normal Mode + ZO O CH M Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness • Used to select transparent of MENU background and language used in MENU. 32 Color Temp.
MENU Background, Language and Key pad Lock Settings 4 Select LANGUAGE by using the “ CH ” Button. ZO - M O + ZO O CH M V O L V O L N E PR V SI ZE MENU • Select LANGUAGE by using the “ CH ” button. • Every press of the “ VOL ” button while you are in the [LANGUAGE] mode would cycle through the different languages.
MGDI (Meta Genuine Digital Image) MGDI is the image enhancement technology of Daewoo Electronics, which provides more clear, splendid, and delicated images. 1 Press the MENU Button. ZO - M O Picture V O L V O L MENU N E PR SI ZE Sound V E RE SC CH CH Normal Mode + ZO O CH M MGDI Demo • The MENU screen will be displayed as below.
Auto Power Setting 4 Auto Power Setting • Select the [Auto Power] by pressing the “ CH M V O L N V the “ VOL ” button. SI ZE MENU E PR • When the AC power is on : Green. • When the AC power is in the standby mode : Red. V O L CH CH E RE SC Picture Sound Screen POWER Features VIDEO/ DVD TV SAT ” button • You can select [Auto Power] ON and OFF mode by using + Front panel LED lights CH from [Features].
Closed Caption Setting • Press the “CAPTION” button on the Remote Control. • Whenever pressing the “CAPTION” button, caption mode is changed as follow. CAPTION Off CC1 CC2 CC3 CC4 XDS Text4 Text3 Text2 Text1 POWER VIDEO/ DVD TV SAT CATV DISPLAY TV/VIDEO MULTIMEDIA O ff M ZO - M O + ZO O CH V O L ZO - M O M + V O L SI ZE N E PR V CH CH E RE SC Sound Screen MUTE F.R/SLOW PLAY REC STOP CAPTION F.
Closed Caption Setting • Select [Features] by pressing the “ CH + Picture V O L Sound N SI ZE MENU V CH ” button. ZO - M O M V O L E PR • Black : Background of the caption box is black. • Transparent : Background of the caption box is Transparent.
Time Setting 1 Press the MENU Button. • The MENU screen will be displayed as below. ZO - M O Picture V O L V O L MENU N E PR SI ZE Sound V E RE SC CH CH Normal Mode + ZO O CH M Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness Color Temp. 32 Normal Features POWER Channel Move MENU VIDEO/ DVD TV Exit • Select [Features] by the “ button.
Time Setting CH M O M ZO - + V O L SI ZE N V CH CH POWER VIDEO/ DVD TV SAT CATV V O L MENU E PR • The “Current time” must be set up ahead of setting up other time memories. 4 Off Time and Wake Time settings. ZO O Clock(current time) Setting E RE SC • Select Functions by pressing the “ CH ” button. First, set [Clock]- current time, and then You can setup off-time and wake time. • [Clock] : Enter clock setting menu by pressing the “VOL ” button.
Image Sticking Minimization(ISM) 1 Press the MENU Button. • The MENU screen will be displayed as below. ISM ZO - M O Picture V O L V O L N E PR V Sound SI ZE MENU E RE SC CH CH Normal Mode + ZO O CH M Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness • Image sticking minimization. • Displaying a still image like PC input for a long time causes part image sticking in the panel • The ISM function minimize this effect. 32 Color Temp.
Image Sticking Minimization(ISM) • Every press of the “ VOL ” button after select function by the “ CH ” button would switch between ON/OFF. CH M ZO - M O + ZO O V O L V O L E PR V SI ZE MENU ISM N 4 Select Functions. CH CH E RE SC Picture Pixel Shift Low Bright Off Off Sound POWER Screen VIDEO/ DVD TV SAT CATV Features Channel Move Adjust MENU Exit DISPLAY TV/VIDEO MULTIMEDIA ZO - M O + ZO O CH M V O L V O L N E PR V SI ZE MENU E RE SC CH CH MUTE F.
Parental Lock Setting 1 Press the MENU Button. Parental Lock • The MENU screen will be displayed as below. M ZO - M O Picture V O L V O L MENU N E PR SI ZE Sound V CH CH Normal Mode + ZO O CH E RE SC Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness Color Temp. • When “Parental Lock” is on, the locked channels are not available on the screen.
Parental Lock Setting New Password setting 4 Press “Password”. • Press Password by using number 0~9. New Password setting menu is displayed at first use. Set New Password for using Parental Lock menu. Caution) If using your password, remember it. It is needed for continuous use of this function hereafter.
ZO - M O + ZO O CH M V O L V O L Off Parental Lock TV GuidLines Sound Movie Retings No Ratings Unblock Ext. Sources Block Screen Change Password N E PR V Parental Control Picture SI ZE MENU • Rating of movie is setup even in movie, videotape and other media objects including TV program.
Parental Lock Setting CH M ZO - M O + ZO O 5 “Change Password”. V O L V O L N E PR V SI ZE MENU CH CH E RE SC POWER VIDEO/ DVD TV SAT • In the initial purchase of TV set, password is set to blank. In continuous use of Parental Control, you need to change your password. • If pressing the “ VOL ” button after selecting password, the second screen of below drawing appears. Here, newly enter your unique password by using number of 0 through 9.
Initialize Setting 1 Press the MENU Button. • The MENU screen will be displayed as below. ZO - M O Picture V O L V O L MENU N E PR SI ZE Sound V CH CH Normal Mode + ZO O CH M Back to Initialization E RE SC Screen Brightness 32 Contrast 48 Color 32 Tint 32 Sharpness 32 Color Temp. • You can restore the values of the adjustment setting made in the MENU to factory settings.
Initialize Setting CH M ZO - M O + ZO O V O L V O L E PR V SI ZE MENU N 3 INITIALIZATION CH CH E RE SC • Enter the sub menu by using the “ VOL ” button. • Select the [Initialize] by pressing the “ CH ” button, then press the “ VOL ” button. • A confirmation message will be displayed. • To perform initialization, press the “VOL ” button after selecting [YES] by pressing the “ CH ” button. • To return to MENU, press "MENU" button.
Setting Sleep Timer Setting Sleep Timer • SLEEP TIMER turns the PDP off after a preset time. POWER VIDEO/ DVD TV Sleep SAT CATV O ff DISPLAY TV/VIDEO MULTIMEDIA CH 30 Sleep Sleep 90 V O L V O L MENU V SI ZE 120 + Sleep 15 Sleep E PR Sleep off ZO - M O Sleep M N SLEEP • Press the “SLEEP” button on the Remote Control. • Pressing the “SLEEP” button first time will display the current setting for SLEEP TIMER.
Before Requesting Service Before requesting for service, check the following points once again. St y o mm ps • Remote control does not function properly. • The Display makes a snapping sound. • There are empty spots at the top and the bottom area of the screen. C h e c k s • Check for any obstacle between the Remote Control and the Display. • Check for dead batteries and incorrect battery orientation. • Check if the Remote Control is the right one. • Check if the pictures and sound are normal.
In the event that the product has been submerged in the water in rainy season: Immediately wash it with clean water, and dry it in a shadow place, then call for service from the nearest Daewoo Service Center. Never plug the Power Cord since there is risk of electric shock and damage of the product. SPECIFICATIONS DISPLAY UNIT Diagonal Size 106cm (42 ) Screen Aspect Ratio 16 : 9 Display Resolution 853(H) 480(V) dots Pixel Pitch 1.08(H) 1.08(V) mm Video Signal NTSC, PAL, SECAM, PAL-M/N, NTSC4.
