User manual

23
LIVE series
ENIT
rimanenti due terminali rimasti scollegati. I loro
valori si sommano: per esempio, due altoparlan-
ti da 8 Ohm in serie danno 16 Ohm.
Quando gli altoparlanti sono collegati in paral-
lelo, i terminali dello stesso segno sono uniti tra
loro. Per ottenere il valore totale bisogna utilizza-
re una formula, indicando con R1 ed R2 i valori
di due altoparlanti, ed eseguire: (R1xR2)/(R1+R2).
Con due altoparlanti da 8 Ohm, per esempio,
avremo: (8x8)/(8+8)= 64/16= 4 Ohm. In pratica
collegando due altoparlanti uguali in parallelo il
valore si dimezza. La lunghezza dei cavi di colle-
gamento deve essere ridotta al minimo neces-
sario.
Come scegliere l’amplicatore
La potenza di lungo termine AES, rappresenta la
potenza termica dissipabile dal diusore o dai
singoli altoparlanti, viene misurata secondo lo
standard AES, che prevede un test di 2 ore con
segnale pink noise, fattore di cresta 2; la potenza
viene determinata dalla tensione RMS al quadra-
to divisa per l’impedenza minima del diusore o
del singolo altoparlante. La potenza dell’ampli-
catore consigliato non viene misurata, ma è pari
al doppio della potenza AES e tiene conto delle
capacità dinamiche degli altoparlanti di soppor-
tare picchi di potenza per brevi istanti di tempo.
Il valore fornito corrisponde alla potenza RMS che
l’amplicatore deve avere per fornire il segnale di
test (pink noise con fattore di cresta 2) usato per
misurare la potenza AES. Un amplicatore con
tale potenza, se usato con segnali musicali con
fattore di cresta maggiore o uguale a 6dB, per-
mette di ottenere il massimo delle prestazioni del
diusore, erogando una potenza di lungo perio-
do non superiore a quella AES del diusore.
Se, viceversa, si usano segnali musicali molto
compressi o il volume viene alzato no al punto
da spingere fortemente in clipping l’amplica-
tore, allora, la potenza eettiva di lungo perio-
do erogata, tende a raggiungere o addirittura
superare quella RMS dell’amplicatore, danneg-
giando in modo irreparabile gli altoparlanti. Con
questo tipo di segnale è consigliabile usare un
amplicatore con potenza RMS pari alla potenza
AES del diusore, facendo comunque attenzio-
ne a non fornire un segnale di ampiezza tale da
portare troppo spesso in clipping l’amplica-
ance value corresponds to the amplier output
impedance.
There are 2 possible connection systems: serial
or parallel mode.
Connecting two speakers in series means to
connect the positive pole of the rst speaker to
the negative pole of the second one and then
to connect the two free poles to the amplier.
In this case the impedance values are summed
up: e.g. Two 8 Ohm speakers connected in paral-
lel give a 16 Ohm load. To connect two speakers
in parallel mode, simply interconnect the two
speakers terminals of the same sign. To obtain
the total value, in this case a calculation is re-
quired. Indicating R1 and R2 as the two loud-
speaker values, the following formula has to be
used: (R1xR2)/(R1+R2).
E.g.: with two 8 Ohm speakers, we have that:
(8x8)/(8+8)= 64/16= 4 Ohm, that is to say that
when identical speakers are connected in paral-
lel, the impedance value is halved.
Choosing the right amplier
According to the AES standard, tests run on the
components require a two-hour stressing of a
ltered pink noise signal with a pass band of a
decade and with a crest factor (average value
and peak value ratio) of 6 dB.
For common applications which require both a
high power and a high reliability level, it is ad-
visable to use power ampliers with an output
rating equivalent to the AES power rating of the
enclosures. This ensures that the enclosures will
operate within their thermal limit specication.
For applications where the user desires to take
advantage of the full applicable power of the
enclosures, it is possible to use amplication
with output power ratings equal to the program
output rating of the enclosures.
In this conguration, the full capacity of the sys-
tem to handle transient power is utilised, how-
ever it will be necessary to constantly monitor
and regulate the system very carefully in order
to avoid overloading the speakers. It is also nec-
essary to avoid that loudspeakers are subject to
signals which could cause them to exceed their
mechanical limits or their applicable frequency
limits.
In practice, it is possible to damage a loud-