cacor a rr renee Installation 24-Inch Instructions Dishwasher For use with models: ED24, |ID24, MDH24, MDV24 and PD24 Part No. 101891 Rev.
Table of Contents Important Safety INStruCtiONS .........cccceeeeesesesesereeereeees Important Information About Safety Instructions.............. Safety Symbols and Labels .............ccccccccccccceeeeeeeeeeeeneeenes General Safety Precautions .............c.cccccccccccceeeeeeeeeeenenenes Design Specifications ..........cccccccceceecececeeeeeeeeneeseneneneeeeeeeees Product Specifications. ..........ccccccccccssssseseseseeeeeeeeeseseeeeeneees Preparing for Installation ............
Important Safety Instructions Important Information About Safety Instructions * « Safety Symbols and Labels DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover ail possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. immediate hazards.that WILL result-in severe. personal injury or death.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING WARNING «Do not install or operate this dishwasher if it-has been damaged, dropped, has damaged electrical conduit.or wires. or is not working properly. If the product is damaged.when received, immediately contact the dealer. or builder. ¢.
Design Specifications Product Specifications Technical Water Pressure | 20 to 120 psi (138 - 827 kPa) Water Temperature | 120 °F, minimum Electrical Circuit Requirements 15 Amp. Total Connected Load 12 Amp. @ 120 Vac, 60 Hz.* 120 Vac, 60 Hz dedicated, grounded, circuit. * For reference only. For exact specifications see the product data label located inside the left door jamb. Dimensions Tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated t{—— 23 7/8” (60.
Preparing for Installation WARNING IMPORTANT: Foilow all cabinet and countertop minimum dimensions shown below to insure safe operation. Observe.all governing codes and-ordinances during planning and installation. Contact-your local building department for further information. Preparing the Location Carefully check the location where the dishwasher is to be installed. Put it in a location with convenient access. Make certain that electrical power can be provided in the selected location.
Preparing for Installation Power Supply Preparation Plumbing Preparation * The-electrical power supply for the disnwasher must be installed only by:a licensed electrician as specified below. It is the owner’s responsibility. to:ensure that the electrical connection of this appliance is performed by.a licensed The water pressure must be between 20 and 120 psi (138-827 kPa). The household hot water heater must supply a minimum of 120 °F water to the dishwasher location for best results.
Installation Instructions Verify the Package Contents NOTE: Model ID24 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. « With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. * Remove ail of the packing materials from inside and outside of the unit. DO NOT allow any of the shipping materials, loose screws or plastic to remain inside.
Installation Electrical Connection Instructions 5. WARNING Remove the dishwasher junction box cover screw and remove the cover. The junction box is mounted to the dishwasher chassis below the door. «Do. not-install the dishwasher unless the electrical service.provided meets the dishwasher specifications (see page 5). «To avoid an electrical:shock hazard, turn off:power to the electrical outlet or junction box: at the circuit breaker panel or fuse.box before proceeding. Do.not turn on the power or water.
Installation Instructions Electrical Connection (Continued) 13. Feed the electric wire or cord into the utility hole in the side of the cut-out. Pull all of the slack out of the wire. If the unit is to be connected directly to the house wiring: With power turned off at the circuit breaker or fuse box, remove the house junction box cover. Feed the dishwasher wiring into the junction box. Secure the wire with a UL/CSA approved strain relief.
Installation Plumbing Connections Instructions Installing the Unit in the Cabinet 1. Connect one end of the 3/8” flexible braided hot water inlet hose to the hot water supply valve. 2. Prepare to prime the hose by routing it through the back of the unit near the bottom and pull the end out of the utility access hole on the left side of the appliance. To prime, put the unconnected end of the hose over a bucket. Turn on the hot water valve to clean out any debris in the hose and to fill it with water.
Installation Instructions Installing the Unit in the Cabinet Attach the anti-Tip Brackets: (continued) CAUTION NOTE: The leg nuts can be removed to make the dishwasher lower. To do so: 1. Turn the leg until it comes out of the chassis. 2. Remove the nut from the leg. 3. Re-thread the leg into the chassis. 4. Reach inside the chassis from the back and thread the «--Make sure to anchor-at least:one-anti-tip bracket-on each side of the dishwasher.
Installation Instructions Cabinet Panel Installation (Model ID24 Only} * For proper door spring operation, the maximum door panel weight, including hardware, is 12 lbs. (5.4 kg). « Install the custom panel and/or according to the instructions on (Dacor PN 101934). If the panel door hardware, attach it before custom toe kick the included template requires decorative panel installation. CAUTION +. To prevent.corrosion and the possibility.
Installation Instructions Drain Line Installation CAUTION For-proper dishwasher operation and.drainage, the drain line: must.be-routed through the bottom of the cabinet:and-up to the drain or-air gap connection. The drain hose or.air gap outlet must.connect above the sink trap. lf required, the air gap must-be installed at-countertop level. Connect the flexible drain line to the air gap or directly to the drain tee or disposal above the sink trap as shown below. Tighten the holding clamp.
Installation Verifying Proper Operation WARNING «To ensure.a safe and proper installation, the following checklist should be completed :-by.the installer-to ensure .that:no part of the installation has. been overlooked and the unit.is. working properly. «Proper installation is the responsibility of the homeowner. The.importance of proper installation of your Dacor dishwasher cannot be overemphasized.
cdacor The Life of the Kitchen® Dacor e Phone: (800) 793-0093 « FAX: (626) 403-3130 « www.Dacor.
