Installation Instructions 24 - Inch Dishwasher For use with models: ED24, ID24, MDH24, MDV24 and PD24 Part No. 101891 Rev.
Table of Contents Important Safety Instructions........................................... 1 Important Information About Safety Instructions............... 1 Safety Symbols and Labels.............................................. 1 General Safety Precautions.............................................. 2 Design Specifications........................................................ 3 Product Specifications....................................................... 3 Preparing for Installation...................
Important Safety Instructions Important Information About Safety Instructions • • Safety Symbols and Labels The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: Warning • Do not install or operate this dishwasher if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder.
Design Specifications Product Specifications Technical Water Pressure 20 to 120 psi (138 - 827 kPa) Water Temperature 120 °F, minimum Electrical Circuit Requirements 15 Amp. 120 Vac, 60 Hz dedicated, grounded, circuit. Total Connected Load 12 Amp. @ 120 Vac, 60 Hz.* * For reference only. For exact specifications see the product data label located inside the left door jamb. Dimensions Tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated 23 7/8” (60.6 cm) ED24: 29 5/8" (75.
Preparing for Installation IMPORTANT: Follow all cabinet and countertop minimum dimensions shown below to insure safe operation. warning Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Preparing the Location Carefully check the location where the dishwasher is to be installed. Put it in a location with convenient access. Make certain that electrical power can be provided in the selected location.
Preparing for Installation Power Supply Preparation warning The electrical power supply for the dishwasher must be installed only by a licensed electrician as specified below. It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a licensed electrician. Plumbing Preparation • The water pressure must be between 20 and 120 psi (138-827 kPa). The household hot water heater must supply a minimum of 120 °F water to the dishwasher location for best results.
Installation Instructions Verify the Package Contents NOTE: Model ID24 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. • Remove all of the packing materials from inside and outside of the unit. DO NOT allow any of the shipping materials, loose screws or plastic to remain inside.
Installation Instructions Electrical Connection 5. Remove the dishwasher junction box cover screw and remove the cover. The junction box is mounted to the dishwasher chassis below the door. warning • Do not install the dishwasher unless the electrical service provided meets the dishwasher specifications (see page 5). • To avoid an electrical shock hazard, turn off power to the electrical outlet or junction box at the circuit breaker panel or fuse box before proceeding.
Installation Instructions Electrical Connection (Continued) 13. Feed the electric wire or cord into the utility hole in the side of the cut-out. Pull all of the slack out of the wire. If the unit is to be connected directly to the house wiring: • With power turned off at the circuit breaker or fuse box, remove the house junction box cover. • Feed the dishwasher wiring into the junction box. Secure the wire with a UL/CSA approved strain relief.
Installation Instructions Plumbing Connections Installing the Unit in the Cabinet 1. Connect one end of the 3/8” flexible braided hot water inlet hose to the hot water supply valve. warning Do not allow any material, including the hoses or electrical wiring to be directly behind the dishwasher while pushing it into the cut-out opening. Carefully pull the slack out of both hoses and the wiring from outside the cut-out during push back to prevent pinching.
Installation Instructions Installing the Unit in the Cabinet Attach the Anti-Tip Brackets: CAUTION (continued) NOTE: The leg nuts can be removed to make the dishwasher lower. To do so: • 1. Turn the leg until it comes out of the chassis. Make sure to anchor at least one anti-tip bracket on each side of the dishwasher. • The anchoring material must be no more than 1/4” (6mm) from the anti-tip bracket. • To prevent leaks, square the dishwasher in the cutout.
Installation Instructions Cabinet Panel Installation (Model ID24 Only) • For proper door spring operation, the maximum door panel weight, including hardware, is 12 lbs. (5.4 kg). • Install the custom panel and/or custom toe kick according to the instructions on the included template (Dacor PN 101934). If the panel requires decorative door hardware, attach it before panel installation.
Installation Instructions Drain Line Installation caution • • For proper dishwasher operation and drainage, the drain line must be routed through the bottom of the cabinet and up to the drain or air gap connection. The drain hose or air gap outlet must connect above the sink trap. If required, the air gap must be installed at countertop level. 1. Connect the flexible drain line to the air gap or directly to the drain tee or disposal above the sink trap as shown below. 2. Tighten the holding clamp.
Installation Instructions Verifying Proper Operation □□You should hear the dishwasher drain and then begin to fill with water. Wait approximately two (2) minutes, then carefully open the door to verify water is filling the dishwasher tank. If there is water present, close the door and continue the process. Should the water not fill the tank or the pump is not running, immediately push the START/STOP button to stop the dishwasher.
Dacor ● Phone: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.
