INSTALLATION 24-INCH INSTRUCTIONS DISHWASHER For use with models: ED24, ID24, MDH24, MDV24, PD24AG, PD24BK, PD24BU, PD24GN, PD24SG, PD24TS Part No. 101891 Rev.
Before You Begin .............................................................. 1 Important Safety Instructions ....................................... 1-3 Product Specifications ..................................................... 3 Technical .......................................................................... 3 Dimensions ...................................................................... 3 Preparing for Installation ............................................... 4-5 Preparing the Location ....
To reduce the risk of fire, electric shock, serious injury or death when using the dishwasher, follow basic safety precautions, including the following: 2 _aCD_
TECHNICAL Water Pressure Water Temperature Power Requirements 20 to 120 psi (138 - 827 kPa) 120°F, minimum 15A, 120 Vac, 60 Hz dedicated, grounded, circuit. See the model number label on product for total connected loaded. DIMENSIONS Tolerances: +1/16", -0, (+1.6 mm, -0) unless otherwise stated I,, 23 7/8" (60.6 cm) '1 1 118"(2.9cm)] -J lnrT_ 2 3/8" (6.0 cm)- .,- : 26" (66.0 cm) ED24: 295/8"(75.2cm) ID24: r 33 3/4" (85.7 cm) to 26 7/8" (68.3 cm) 36 1/4" (92.1 cm) 1 tt2" (3.8cm) _ _.
4 _aCD_
PREPARING THE LOCATION IMPORTANT: Follow all cabinet and countertop minimum dimensions shown below to insure safe operation. Carefully check the location where the dishwasher is to be installed. Put it in a location with convenient access. Make certain that electrical power can be provided in the selected location. Plan the installation so that the appliance can be removed if service is required. Fasten anti-tip under counter anchors Prepare the installation location as shown below.
POWER SUPPLYPREPARATION PLUMBING PREPARATION The water pressure must be between 20 and 120 psi (138-827 kPa). The household hot water heater should supply a minimum of 120°F water to the dishwasher location for best results. Electrical Install a water supply valve for the hot water supply line where it is easily accessible after the dishwasher is installed. The dishwasher is shipped with a 3/8 male corn )ression fitting to facilitate installation.
VERIFYTHE PACKAGE CONTENTS NOTE: Model ID24 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. • Remove all of the packing materials from inside and outside of the unit. DO NOT allow any of the shipping materials, loose screws or plastic to remain inside. Remove the racks.
. Remove the dishwasher junction box cover screw. The junction box is mounted to the dishwasher chassis below the door. r _ Junction Box Location . 6. Remove the junction box cover. Install a 3/4" UL/CSA approved strain relief on the base of the dishwasher junction box. Strain relief _ _ Wire nuts ELECTRICALCONNECTION . 2. Make sure power to the electrical receptacle or junction box is off.
ELECTRICALCONNECTION (Continued) 13. Feed the electric wire or cord into the utility hole in the side of the cut-out. Pull all of the slack out of the wire. If the unit is to be connected house wiring" directly to the • With power turned off at the circuit breaker or fuse box, remove the house junction box cover. • Feed the dishwasher wiring into the junction box. Secure the wire with a UL/CSA approved strain relief. • Strip and connect the wires according to one of the wiring diagrams below.
PLUMBING CONNECTIONS 1. Connect one end of the 3/8" flexible braided fill hose to the water supply valve. 2. Route the hose through the utility access hole in the side of the appliance cut-out. Put the unconnected end of the hose over a bucket. Turn on the water to clean any debris out of the supply line and fill the hose for leak testing. Turn the valve off. 3. Keeping as much water as possible in the hose, route it through the bottom of the dishwasher chassis and connect it to the water inlet.
INSTALLING THE UNIT IN THE CABINET (continued) NOTE: The leg nuts can be removed to make the dishwasher lower. To do so: 0 Turn the leg until it comes out of the chassis. 0 Remove the nut from the leg. 0 Re-thread the leg into the chassis. 0 . To attach the anti-tip bracket anchors, insert the anchoring screws through the 1/2" diameter access holes inside the dishwashing compartment on the ceiling and the sides, near the front.
DRAIN LINE INSTALLATION . Connect the flexible drain line to the air gap or connect it directly to the waste tee or disposal (see below). 2. For installations without an air gap, put a loop in the drain line as shown. 3. Tighten the holding clamp. For installations with an air gap check to make sure the drain line from the air gap to the disposal/drain trap is complete and that the clamps are tight. Create loop and fasten to under side of cabinet I .vp __ n Min.
VERIFYING PROPEROPERATION Pre-verification [] You should hear the dishwasher drain and then begin to fill with water. Wait approximately two (2) minutes, then carefully open the door to verify water is filling the dishwasher tank. tf there is water present, close the door and continue the process. Should the water not fill the tank or the pump is not running, immediately push the START/STOP button to stop the dishwasher.
INSTALLATION INSTRUCTIONS
