Installation Instructions Modernist Warming Drawer DWR30M977WS, DWR30M977WM Part No.
Contents Contents Before you begin... 3 Important 3 Customer-service information 4 If You Need Help...
Before you begin... Important Customer • Keep these installation instructions for future reference and the local electrical inspector’s use. English 3 Before you begin... Installer • In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you begin the installation process. • Leave these installation instructions with the customer.
Customer-service information If You Need Help... Customer-service information For answers to general questions or installation issues, call your Dacor® dealer or Dacor Customer Service. For repairs to Dacor appliances under warranty, call the Dacor Distinctive Service line. Before calling, have available the appliance's model and serial numbers, which are on the Product Data Label (drawer front, interior side). Dacor Modernist Service (repairs under warranty only) Phone: (800) 793-0093 ex.
Important safety instructions Related equipment safety • Remove all tape and packaging before using the unit. • Dispose of the packaging after unpacking the unit. • Never let children play with packaging material. • Never alter the the appliance (e.g., do not remove panels, wire covers, or screws).
Important safety instructions To reduce risk of fire, electric shock, serious injury or death when using your appliance, follow basic precautions, including the following: • • • • • • • Important safety instructions • • • • • • • • WARNING Clean the warming drawer thoroughly before operating it for the first time. Do not use harsh scrubbers, cleaners, or detergents, which may permanently mar the unit's finish. Do not use aerosol cleaners, which may be flammable and corrode metal.
• • • • • • Ensure that anyone who uses the unit knows how to operate it properly. Do not tamper with the controls. Never let anyone sit, stand, or climb on the open drawer. Do not leave children unattended near the unit. Do not let children play with the controls or other components. Do not store items of interest to children above the drawer. DANGER • • • Ensure the unit is properly installed and grounded by a qualified installer as instructed in this manual.
Installation requirements Checklist WARNING To ensure proper installation, the installer should complete this checklist. The owner shall verify proper installation, the importance of which cannot be overstated.
Necessary Tools Phillips Screwdriver Drill Verifying Package Contents The items in this section are provided with the warming drawer. If these items are not with the unit, contact your Dacor Service Center or Dacor Customer Service (pg. 4). 7 mounting screws (PN83569) Half Shelf (PN110346) Installation planning • A qualified technician must install the unit. The owner shall verify proper installation. • Carefully review the unit's installation site. Access should be convenient.
Installation requirements Warming drawer dimensions Overall dimensions (top view) Chassis (drawer removed) (A) Installation requirements Model No. Chassis Face (B) Chassis Width (C) (D) (E) Chassis Depth Drawer Depth Chassis Height 27 7/8" (70.8 cm) 22 7/8" (57.7 cm) 20" 9 3/4" (24.8 cm) Width DWR30M977WS DWR30M977WM 10 English 29 5/8" (75.2 cm) (58.
Drawer and Chassis dimensions 10" (25.5 cm) 29 3/4" (75.6 cm) 1 3/8” (3.5 cm) 10 1/4" (26.0 cm) Installation requirements 1 3/8” (3.5 cm) 1 13/16" (4.
Installation requirements Cutout & Cleat dimensions Installation requirements 12 English
Model No. (A) Cut out Width (B) Min. Width to Adjacent Doors/ Drawer (C) Cutout Height 30 1/4” 10 1/2” DWR30M977WS 30 1/4” DWR30M977WM (76.8 cm) (76.8 cm) (26.7 cm) (D1) (D2) (E1)+ Min. Min. Flush to Vertical Gap Vertical Gap Drawer Between Between Front Warming Dacor Wall Drawer cutouts Oven 1 ¼” (3.2 cm) 1 ½” (3.8 cm) 1 1/8” (2.9 cm) (E2)++ Flush to Cabinet Frame 1 13/16" (4.6 cm) (F) Min. Width Inside Cleats 28" (71.0 cm) (G) Min. Cutout Depth 24" (61.0 cm) for E1; 24 3/4" (62.
Installation instructions Install support platform in cabinet Provide a platform (100 lb. load capacity) within the cabinet to support the unit. The platform must be installed level and straight. The platform must be flush with the cutout at the front of the cabinet. (See the graphic.) There is no way to level the warming drawer after installation. 3/4” (1.9 cm) thick plywood is recommended.
Electrical connection WARNING Electrical Shock Hazard IMPORTANT: The unit has a three-prong, grounding plug to prevent possible electric shock. If a two-prong electrical outlet is available, the owner must have it replaced with a dedicated, properly grounded, three-prong electrical outlet. To avoid an electric shock hazard, DO NOT: • • • • • remove the cord's third (ground) prong. use an adapter plug. use a worn/damaged cord. immerse the cord or plug in liquid. Connect the appliance to an extension cord.
Installation instructions Nominal Electrical Supply Requirements 120 Vac, 60 Hz, 15 Amp., dedicated circuit The warming drawer is supplied with a 40” (101.6 cm) power cord with a three-prong grounded plug. Total Connected Load 0.5 kW (4 Amp.) • • • • The owner shall ensure that a qualified electrician performs the installation, which must comply with the latest revision of the National Electric Code ANSI/NFPA 70, and local codes and ordinances.
Remove and re-install drawer WARNING • • • To avoid personal injury caused by the unit being pulled from its cutout when the drawer is opened, secure the chassis to the cabinet as instructed. (See pg. 14.) The unit should be secured to the cabinet cutout while the drawer out of the unit. Unplug the unit before removing the drawer. Disconnect the Control wire harness Remove one screw from the clamp, locate the control wire harness, and disconnect it before removing the drawer.
Installation instructions Remove the drawer from the appliance 1. Open the drawer fully, and remove the clamp screw. 2. Pull out the clamp, and detach the connector. Connector 3. Remove the screw from the Drawer (both sides, near the front. 4. Installation instructions 18 English Remove the drawer.
Re-installing the drawer 1. Extend both rails, and pull out the cable (right side) so the connector hangs outside the frame. Put the drawer on both rails, and slide it in until it engages under the rails' rear clips. Clip on slide Slide 2. Fasten the screws on both sides. 3. Re-attach the connector. 4. With the cable under the cable cover, insert the clamp through the square hole, and fasten the screw.
Installation instructions Verify warming drawer operation 1. Plug in the unit. 2. Open the drawer, and press POWER on the control panel. 3. (Temperature section) One after the other, press Bread Proof, Low, Med, and High. As 4. 5. 6. 7. you press each function, the indicator above it should light. Leave the control panel set to High. (Duration section) Press -, +, and +1hr. Verify that the timer display is correct. Within 5 – 10 minutes, you should feel heat from the drawer interior.
MEMO
MEMO
MEMO
Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.
