Installation Instructions Modernist Warming Drawer DWR30M977WIP, DWR30M977WIM, DWR30M977WIS Part No.
Contents 3 Important 3 3 3 4 4 6 6 6 6 7 7 10 Installing the custom front panel 2 English 10 11 12 15 19
Before You Begin Important Installer • For safety's sake and to minimize problems, read this manual thoroughly before installing the warming drawer. • Leave this manual with the customer. Customer • Keep this manual for reference and the electrical inspector’s use. Customer-Service Information If You Need Help For answers to general questions or installation issues, call your Dacor® dealer or Dacor Customer Assurance. For repairs to Dacor appliances, call Dacor Customer Assurance.
Important Safety Instructions Related equipment safety • Remove all tape and packaging before using the unit. • Dispose of the packaging after unpacking the unit. • Never let children play with packaging material. • Never alter the the appliance (e.g., do not remove panels, wire covers, or screws).
Important Safety Instructions WARNING To reduce risk of property damage, fire, electric shock, serious injury, or death when using your appliance, follow basic precautions, including: • Clean the unit thoroughly before operating it for the first time. • Do not use harsh scrubbers, cleaners, or detergents, which may permanently mar the unit's finish. Do not use aerosol cleaners, which may be flammable and corrode metal. • Use the drawer only to warm food, dishes, and utensils.
Installation Requirements Checklist WARNING To ensure proper installation, the installer should complete this checklist. The owner shall verify proper installation.
Installation planning • A qualified technician must install the unit. The owner shall verify proper installation. • Carefully review the unit's installation site. Access should be convenient. Verify that electrical power can be provided. Install the warming drawer in wood cabinets only. • All minimum clearances must be met or exceeded. Dimensions show minimum clearances unless otherwise noted. Ensure the drawer can be opened fully unhindered.
Installation Requirements Drawer and Chassis dimensions Drawer for WIP Model without Front Panel Attached Drawer for WIP Model with Front Panel Attached Drawer for WIM and WIS Models 8 English
Installation Requirements Cutout & Cleat dimensions Measurement DWR30M977 (A) Cutout Width 30 1/4” (76.8 cm) (B) Min. Width to Adjacent Doors/Drawer 30 1/4” (76.8 cm) (C) Cutout Height 10 1/2” (26.7 cm) (D1) Min. Vertical Gap Betw. Warming Drawer Cutouts 1 1/4” (3.2 cm) (D2) Min. Vertical Gap Betw. Dacor Wall Oven 1 1/2” (3.8 cm) (E1) Flush to Drawer Front (see page 16) 1 5/64” (2.7 cm) (E2) Flush to Cab’t Frame / Drawer with Panel Flush to Drawer Front (see page 17) 1 53/64” (4.
Installation Instructions Install support platform in cabinet Provide a platform (100 lb. load capacity) within the cabinet to support the unit. The platform must be level, straight, and flush with the crossbrace at the front of the cutout. (See the graphic.) The unit cannot be leveled after installation. 3/4” (1.9 cm) thick plywood is recommended. NOTE If the unit is not level , the drawer may slide open on its own or may not seal tightly, compromising performance.
Electrical Connection WARNING Electrical Shock Hazard IMPORTANT: The unit has a 3-prong grounding plug to prevent possible electric shock. If a dedicated, grounded, 3-prong outlet is unavailable, the owner must have one installed. To avoid an electric shock hazard, DO NOT: • Remove the cord's third (ground) prong • Use an adapter plug • Use a worn/damaged cord • Immerse the cord or plug in liquid • Connect the appliance to an extension cord • Use a ground fault interrupter (GFI).
Installation Instructions Nominal Electrical-Supply Requirements 120 Vac, 60 Hz, 15 Amp., dedicated circuit The unit comes with a 40” (101.6 cm) power cord with a 3-prong grounded plug. Total Connected Load: 0.5 kW (4 Amp.) • • • • The owner shall ensure that a qualified electrician performs the installation, which must comply with the latest revision of the National Electric Code ANSI/NFPA 70, and local codes and ordinances.
Installation Instructions Remove the drawer from the appliance 1. Open the drawer fully, and remove the clamp screw. 2. Extract the clamp, and detach the connector. Connector 3. Remove the screw from the Drawer (both sides), near the front. 4. Remove the drawer from the chassis.
Re-installing the drawer 1. Extend both rails, and pull out the cable (right side) so the connector hangs outside the frame. Put the drawer on both rails, and slide it in until it engages under the rails' rear clips. Clip on slide Slide 2. Fasten the screws on both sides. 3. Re-attach the connector, and feed it into the cable cover. Connector 4. With the cable under the cable cover, insert the clamp through the square hole, and fasten the screw. 5. Plug in the unit.
Installation Instructions Installing the Custom Front Panel This section instructs you how to attach the custom front panel to the warming-drawer face. The panel must be at least 1/2" thick to accommodate the length of the provided screws. 1. On the back of the custom panel, locate the vertical centerline. 2. Measure 8-15/16" from the centerline in both directions, and mark each position with a vertical guideline, ensuring each guideline is square with the panel edges.
Installation Instructions Installing the Custom Front Panel, cont. Bracket to Drawer Face (bottom view) 16 English 7. Verify that the screw holes in the brackets and the drawer face align properly. 8. Carefully center the panel side to side if needed. (Some leeway is designed into the product to allow for minor side-to side adjustment.) 9. Before permanently attaching the custom panel, close the drawer to verify that it will seat properly in the cabinetry, and adjust the panel if needed. 10.
Installation Instructions English 17
Installation Instructions 18 English
Installation Instructions Verify warming drawer operation 1. Plug in the unit. 2. Open the drawer, and on the control panel, press POWER. 3. (Temperature section) One after the other, press Bread Proof, Low, Med, and High. As you press each function, the indicator above it should light. 4. Leave the control panel set to High. 5. (Duration section) Press -, +, and +1hr. Verify that the timer display is correct. 6. In 5 – 10 minutes, you should feel heat from the drawer interior. 7.
Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.
