Installation Manual
Table Of Contents
- Dacor_FDR_BRF8000M_IM_DA68-03621A-07_EN
- Before you begin...
- Customer-Service Information
- Important Safety Instructions
- Safety and warning information
- Installation Specifications
- Product Specifications
- Installation
- Installation requirements
- Installation instructions
- 1. Uncrating the Refrigerator
- 2. Moving the Refrigerator
- 3. Installation preparation
- 4. Attaching the anti-tip-bracket
- 5. Remove Upper Door Cover, Kickplate
- 6. Attaching the Refrigerator’s Top Cover
- 7. Adjusting the door Opening Angle
- 8. Moving the Refrigerator Into Its Enclosure
- 9. Leveling the Refrigerator
- 10. Securing the Refrigerator
- 11. Attaching Panel brackets
- 12. Hanging a Custom Panel
- 13. Aligning the Panel
- 14. Attaching the Door’s Interior Covers
- 15. Connecting the Water Line
- 16. Attaching kickplate and Toe kickplate
- 17. Attaching the Refrigerator Trim
- 18. Attaching Trim Top Cover
- 19. Removing the Interior packaging
- 20. Adjusting the door spring
- 21. Cleaning
- 22. Installation Checklist
- Dacor_FDR_BRF8000M_IM_DA68-03621A-07_MES
- Antes de comenzar...
- Información de Atención al cliente
- Instrucciones importantes de seguridad
- Información de seguridad y advertencias
- Especificaciones de instalación
- Especificaciones del producto
- Instalación
- Requisitos de instalación
- Instrucciones de instalación
- 1. Desembalar el refrigerador
- 2. Desplazar el refrigerador
- 3. Preparación para la instalación
- 4. Colocar el soporte antivuelco
- 5. Retirar la cubierta superior de la puerta, placa de protección
- 6. Colocación de la tapa superior del refrigerador
- 7. Ajuste del ángulo de apertura de la puerta
- 8. Colocar el refrigerador en su estructura
- 9. Nivelar del refrigerador
- 10. Ajuste del refrigerador
- 11. Ajuste de los soportes del panel
- 12. Colgar un panel personalizado
- 13. Alinear el panel
- 14. Colocar las cubiertas interiores de la puerta
- 15. Conectar la tubería de agua
- 16. Colocar la placa de protección y el zócalo
- 17. Colocar el borde del refrigerador
- 18. Instalar el borde de la cubierta superior
- 19. Retirar el empaque interno
- 20. Ajustar el resorte de la puerta
- 21. Limpieza
- 22. Lista de verificación de instalación
- Dacor_FDR_BRF8000M_IM_DA68-03621A-07_CFR
- Avant de commencer...
- Informations relatives au service client
- Consignes importantes relatives à la sécurité
- Consignes et avertissements de sécurité
- Spécifications relatives à l'installation
- Caractéristiques techniques de l'appareil
- Installation
- Exigences relatives à l'installation
- Instructions d'installation
- 1. Déballage du réfrigérateur
- 2. Déplacement du réfrigérateur
- 3. Préparation à l'installation
- 4. Fixation du support antibasculement
- 5. Retrait du cache supérieur de la porte, plinthe
- 6. Fixer le cache supérieur du réfrigérateur
- 7. Ajustement de l’angle d’ouverture de la porte
- 8. Placer le réfrigérateur dans son caisson
- 9. Mise à niveau du réfrigérateur
- 10. Fixation du réfrigérateur
- 11. Fixation des supports du panneau
- 12. Fixation d'un panneau personnalisé
- 13. Alignement du panneau
- 14. Fixation des caches intérieurs de la porte
- 15. Raccordement de la conduite d'eau
- 16. Fixation de la plinthe et de la patte
- 17. Fixation de l'habillage du réfrigérateur
- 18. Fixation du cache supérieur de l'habillage
- 19. Retrait de l'emballage intérieur
- 20. Ajustement du ressort de la porte
- 21. Nettoyage
- 22. Liste de vérifications pour l'installation
Installation instructions
English28
3. Installation preparation
Unpack installation materials and accessories.
See the Installation preparation section on Installation Requirement chapter.
4. Attaching the anti-tip-bracket
WARNING
To keep the unit from tipping forward, an anti-tip bracket must be installed. Before
attaching the bracket, ensure that no electrical wiring or plumbing is in the area where the
screws will penetrate. One such bracket per appliance is required.
CAUTION
Always wear safety glasses and other necessary protective devices or apparel when
installing or working with anchors.
Dacor does not recommend that you anchor the anti-tip bracket in light-weight masonry
(e.g., block, brick) or in new, uncured concrete.
Make sure the wall or the cabinet that the brackets are studded in has enough strength to
withstand the safety load.
M4x35
Wooden Wall
3 ea
Concrete Wall
M4x35
ø6x30
3 ea
3 ea
1. Bracket height is measured from the
oor and depends on the cabinet
height.
NOTE
Bracket height
= Cabinet height – 4 3/32” (104 mm)
2. Attach the anti-tip brackets. Ensure the
screws hold the bracket tightly.
The anti-tip brackets must extend at least 2” (50 mm) over the appliance to secure the
appliance. If this minimum length cannot be observed for structural conditions it is
possible to do this by fastening a spacer (wood) behind the anti-tip angle.
Dacor_FDR_BRF8000M_IM_DA68-03621A-07_EN.indd 28 2020-11-16 4:22:44