LP Conversion Guide

ManualsBrandsDacor ManualsGas RangesDacor Modernist Pro 36" Stainless Steel Natural Gas Range

2. Converting the surface burners

The range comes with low-altitude LP conversion kits.

The kit contains 16 burner orices. Fourteen of these

16 orices are sized and color-coded for surface burner

use. The remaining 2 orices are for the bake and broil

oven burners. Use the following charts to properly size

and replace the orices:

BURNER ORIFICE SIZES AND OUTPUT RATINGS

(LP Gas [Propane] 10 in WCP)

Burner Location BTU Rate Orice size [mm]

LF 16500 In : 0.46 / Out : 0.78 (2 pcs)

LR 14500 In : 0.46 / Out : 0.74 (2 pcs)

CF 14500 1.12

CR 14500 1.12

RR 14500 In : 0.46 / Out : 0.74 (2 pcs)

RF 16500 In : 0.46 / Out : 0.78 (2 pcs)

BAKE 23000 1.4

BROIL 14500 1.12

115

Orice markings:

115 – Denotes 1.15 mm orice size

opening.

BURNER ORIFICE SIZES AND OUTPUT RATINGS

(Natural Gas 5 in WCP)

Burner Location BTU Rate Orice size [mm]

LF 22000 In : 0.85 / Out : 1.40 (2 pcs)

LR 16000 In : 0.70 / Out : 1.17 (2 pcs)

CF 16000 1.78

CR 16000 1.78

RR 16000 In : 0.70 / Out : 1.17 (2 pcs)

RF 22000 In : 0.85 / Out : 1.40 (2 pcs)

BAKE 25000 2.34

BROIL 18000 1.90

180

Orice markings:

180 – Denotes 1.80 mm orice size

opening.

A. Remove the surface burner grates.

B. Lift off the surface burner caps and the surface

burner heads from the surface burner manifold cups.

C. Using a 9/32˝ or 7 mm nut driver, remove the burner

orice from the bottom of each manifold cup.

NOTE

Keep these orices and note their positions for

future conversion back to natural gas.

LR-OUT (PUR)

IN (GRAY)

LF-OUT (NAVY)

IN (GRAY)

CR (ORG)

CF (ORG)

RR-OUT (PUR)

IN (GRAY)

RF-OUT (NAVY)

IN (GRAY)

D. Identify the proper orice by orice size and color

code for each of the surface burners.

E. Install the proper orices in each of the burner

manifold cups as shown above. Tighten with a 9/32˝

or 7 mm nut driver. Do not overtighten.

NOTE

Any other placement of orices could result in

dangerous operating conditions and/or poor cooking

results.

F. Replace the surface burner heads and caps in the

same location from which they were removed. The

burner heads should be at on top of the manifold

cups and the caps should be at on top of the burner

heads to ensure proper, safe operation.

3. Converting the oven burners

WARNING

The following adjustments must be made before

turning on the gas to the oven burners. Failure to

do so could result in death and/or serious personal

injury due to high ames and toxic fumes.

The oven has a bake (lower) and a broil (upper) oven

burner. Both burners require the orices to be changed.

See the charts in column 2 for the proper orice usage.

To replace the bake (lower) burner orice:

A. Remove the two screws from the back of the cavity

oor. Lift back to clear the front edge and lift out the

cavity oor.

B. Remove three screws from the front of the bracket

bake-spreader.

C. Lift front the bracket bake spreader and lift out the

bracket-bake spreader.

D. Lift up the burner bake from the bake burner box.

E. Using a 9/32˝ or 7mm nut driver and an adjustable

wrench, hold the gas tting with the wrench and

remove the bake oven burner orice from the center

of the lower gas tting.

IMPORTANT SAFETY INFORMATIONS

WARNING

The following information is intended for use by

persons possessing adequate electrical, electronics,

and mechanical backgrounds and experience. Lack

of proper background and experience during any

repair of a major appliance could result in death,

personal injury, and/or property damage. The

manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume

any liability in connection with its use.

• Disconnect the electrical power to the appliance

before servicing.

• Shut off the gas supply to the appliance before

servicing.

• Reconnecting all grounding devices before

reconnecting the electrical power and opening the

gas supply to the appliance.

• All electrical components in this appliance are

grounded. All grounding wires, screws, straps,

nuts, and/or washers must be replaced to their

original position and properly fastened.

• LP conversion must be performed by a qualied

installer or gas supplier in accordance with the

manufacturer’s instructions and all codes and

requirements of the authority having jurisdiction.

Failure to follow ALL instructions could result

in serious injury or property damage. The

qualied agency performing this work assumes

responsibility for the conversion.

• Know the location of the gas shut-off valve and

how to shut it off if necessary.

• Do not operate the cooktop surface burners or

oven burners of this range when using LP gas

before converting the pressure regulator and

burner orices for LP gas use. Failure to do so

could cause high ames and toxic fumes which can

result in serious injury.

• Do not mix up or substitute LP gas burner

orices during the conversion process. Improper

orice placement will affect burner and cooking

performance and could result in personal injury

and/or product damage.

LP GAS (PROPANE) CONVERSION

1. Converting the pressure regulator

The regulator is located in the lower, left-hand corner of

the back panel.

A. Locate the pressure regulator on the lower, left hand

of the back panel. The pressure regulator can be

seen and accessed through the square hole of the

back panel.

B. Using at driver, turn the dual purpose orice

counterclockwise to remove from the pressure

regulator.

C. Completely remove the orice and reinstall it on the

opposite side of the spud.

Brass Cap

Dual-Purpose

Orice

Shut-Off

Lever

Flip Orice

to change

application

size.

Pressure

Regulator

D. Reinstall the orice in the pressure regulator so the

large, open LP gas end is exposed. Tighten the spud

using at screw driver. Do not overtighten.

E. Make sure the gas shut-off lever on the side of the

pressure regulator is in the open position.

Mini-Manual_DOP36M96GLM_AA_DG68-01108C-01_EN.indd 1 2019-06-25  1:21:43

Summary of content (4 pages)

PAGE 1
IMPORTANT SAFETY INFORMATIONS WARNING The following information is intended for use by persons possessing adequate electrical, electronics, and mechanical backgrounds and experience. Lack of proper background and experience during any repair of a major appliance could result in death, personal injury, and/or property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use.
PAGE 2
F. Install a properly sized burner orifice for the lower oven burner using LP gas. To replace the broil (upper) burner orifice: G. Remove 1 screw of bracket HSI-wire. H. Remove 4 screws of bracket-broil spreader to top of oven. I. Support the burner-broil with one hand, remove 1 screw supporting the burner-broil to the front of the oven. J. To replace the nozzle broil-burner, remove the gas nozzle with a 9/32˝ nut driver. K. Install a properly sized burner orifice for the upper oven burner, using LP gas. L.
PAGE 3
INFORMATION CODE CHART Displayed code PCB INFORMATION Possible cause Solution LCD SUB C-d1 This code occurs if the door lock is mispositioned. CNS100 This is connector for Power from SMPS PBA. C-F0 This code occurs if communication between the Main and Sub PBA is interrupted. CNS200 This is connector for lighting knob and communicate with Touch IC. CNS202 This is connector for Door LED, Rotary switch and communicate with Bluetooth, Main PBA.
PAGE 4
SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM – COOKTOP Model DOP36M96GL* Model DOP36M96GL* NOTE 1. CIRCUIT SHOWN WITH ALL CONTROLS SET TO OFF 2. OVEN DOOR OPENED AND UNLOCKED DESCRIPTION PCB AREA PCB PATTERN WIRE NOTE 1. CIRCUIT SHOWN WITH ALL CONTROLS SET TO OFF 2. OVEN DOOR OPENED AND UNLOCKED DESCRIPTION PCB AREA PCB PATTERN WIRE DG68-01108C-01 Mini-Manual_DOP36M96GLM_AA_DG68-01108C-01_EN.