Installation Instructions 24 - Inch Built-in Dishwasher Models: EDWH24S and IDWH24 Part No. 106842 Rev.
Table of Contents Important Safety Instructions.......................... 1 Important Information About Safety Instructions... 1 Safety Symbols and Labels............................. 1 General Safety Precautions............................. 2 Product Specifications..................................... 3 Product Dimensions......................................... 3 Planning the Installation................................... 4 Electrical Specifications...................................
Important Safety Instructions Important Information About Safety Instructions • • The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information.
Important Safety Instructions General Safety Precautions WARNING - To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: Warning • • • • • Warning Use this dishwasher only for its intended purpose as outlined in the use and care manual. It is not intended for commercial use. Read the use and care manual completely before use. • Do not tamper with the controls.
Product Specifications Product Dimensions Product tolerances: ±1/16” (±1.6 mm) Style varies, model EDWH24S shown Depth with door open 49 3/4” (126.4 cm) Depth with door closed C A D Handle depth Drain hose Depth dimensions allow for hose on back of unit Side Front B 5 1/4” (13.5 cm) to 7 1/4” (18.5 cm) 2” (50.0 cm) Shipping weight: 108 lbs. (49 Kg) Model Description A B C Stainless steel 24” 34 3/8” (87.4 cm) to EDWH24S front panel (61.0 cm) 36 1/2” (92.
Planning the Installation warning Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Electrical Specifications warning Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes. The dishwasher comes with an electrical cord with a three prong grounding plug for 120 Vac, 15 Amp. supplied.
Planning the Installation Preparing the Location Cutout tolerances: +1/16” (+1.6 mm), -0 warning Follow all cabinet dimensions shown to insure safe operation. All minimum product dimensions must be met or exceeded (see page 3). Dimensions shown on the right provide the required clearances. • • • • Drain line access hole 2” x 2” (5.1 cm x 5.1 cm) Carefully check the location where the dishwasher is to be installed.
Planning the Installation Custom Door Panel/Handle for Model IDWH24 • • Preparing the Drain CAUTION The custom panel mounting screws are provided with the dishwasher. Follow the template included with the dishwasher to ensure that the panel and the accompanying fasteners will fit properly. The handle and handle mounting hardware are not included with model IDWH24. A handle designed for use with an appliance should produce satisfactory results. Do not use a knob or handle attached by a single fastener.
Planning the Installation Disposer connection Disposer connection Air gap Keep higher than disposer connection Keep higher than disposer connection 20” min. Sink trap 20” min. Sink trap Floor Floor Disposer Installation without Air Gap Disposer Installation with Air Gap Waste tee Waste tee Air gap Keep higher than tee connection Keep higher than tee connection 20” min. Sink trap Floor Waste Tee Installation without Air Gap Sink trap 20” min.
Installation Instructions Verify the Package Contents • Remove all styrofoam and plastic wrap from the dishwasher. Be sure to remove the toe kick from the top of the dishwasher packaging. With the assistance of at least one person, remove the dishwasher from the shipping pallet. Place the unit to the side of the cabinet opening. • A Remove the “O” ring attached to the water line in a plastic bag. Set it aside for use during the Water Line Connection.
Installation Instructions Installation Preparation warning • Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. Place a tag at the disconnect switch indicating that you are working on the circuit. • Moving this appliance requires two people. Do not attempt to install or lift it without assistance. • To prevent personal injury, wear hand protection when moving this appliance.
Installation Instructions Handle Installation (Model EDWH24S) 4. Install the door handle according to the handle installation instructions. Adjust the Door Springs Before installation, open the door to check the door springs. If it tends to fall open or pull shut quickly on its own, adjust the springs. If the door opens and closes properly, skip to Level the Dishwasher on page 11. Door spring IMPORTANT: On model IDWH24, if the door panel is between 15 and 23 lbs.
Installation Instructions Level the Dishwasher 4. Open the door and pull the bottom rack out of the dishwasher. Check to make sure the dishwasher floor is level left to right using a level. Adjust the front legs as necessary. 5. Using a flat blade screwdriver, turn the rear leg adjustment screw until the floor of the dishwasher is level front to back. 6. Leave the retaining nuts loose to allow for final leveling after the unit is pushed into place.
Installation Instructions 4. If a nonmetallic cable is being used, install a UL-listed strain relief bushing on the back of the dishwasher. 5. Connect the white wire on the cable to the “N” terminal on the dishwasher terminal block as shown below. 6. Connect the black wire on the cable to the “L” terminal on the terminal block. 7. Connect the ground (green) wire on the cable using a loop or spade terminal to the ground connection screw located on the dishwasher chassis. Junction box 3.
Installation Instructions Drain Connection caution • • 1. For proper dishwasher operation and drainage, the drain line must be routed through the bottom of the cabinet and up to the drain or air gap connection. The drain hose or air gap outlet must connect above the sink trap. 5. Check again that the entire length of the power cable, water line and drain hose are free of pinches or kinks. 6. Verify that the dishwasher is level front to back and side to side inside the cutout.
Installation Instructions Final Leveling 1. 2. Check to make sure that adjacent drawers and cupboards can be opened when the dishwasher door is open. Reposition the dishwasher if necessary. Check that there is a 1/8” (3.0 mm) space between the top of the dishwasher door and the underside of the cabinet. Attaching the Anti-tip Brackets CAUTION Make sure to anchor one anti-tip bracket on each side of the dishwasher. 1.
Installation Instructions Anti-tip Brackets (cont.) 5. 4. Cover the screw holes on the sides with the supplied plastic plugs. Push in the plugs diagonally to fit them in place. Hang the toe kick on the brackets as shown. Check to make sure that the toe kick is even with the kitchen cabinet toe kick. If necessary, remove the toe kick and readjust the brackets. Installation Checklist 6. Replace the top rack. Installing the Toe Kick 1.
Notes 16
Item No., 80 895 92 Rev. 03 Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.Dacor.
