Installation Instructions Millennia®Wall Mount Range Hoods Models: DHW301, APPROVED Part No. 101743 Rev. F DHW361, DHW421 and DHW482 FOR USE WITH ALL DACOR ® RANGES AND COOKTOPS.
Important Safety Instructions ..................................... 1 Important Information About Safety Instructions ......... 1 General Safety Precautions ........................................ 2 Installation Specifications .......................................... 3 Performance Specifications ........................................ 3 Electrical Specifications .............................................. 3 Dimensions .................................................................
Important Information About Safety Instructions Safety Symbols and Labels [_ DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. • Always contact the Dacor Customer Service Team about problems and conditions that you don't understand. Immediate hazards that WILL result in severe pers0nal injury or death.
General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow precautions, including the following: basic sate- WARNING 2 • If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. • Do not install or operate this hood if it has been damaged, dropped, has damaged electrical wires or is not working properly.
Performance Dimensions Specifications All Models Tolerances: +1/16" (+1.6 mm), -0 unless otherwise stated 600 CFM* (for single blower units) 1200 CFM* (for dual blower units) Blower Blower Speeds / 15"-_ 11 3/4" 4 with electronic speed control Lights 12 Vac, 20 Watt halogen Filters Baffle type, dishwasher safe Exhaust 8-inch Finish 430 stainless steel Total Connected Load 120 Vac, 60 Hz. (See table below for current draw) Circuit Requirement 120 Vac, 15Amp.
Planning and Installing the Duct Work WARNING • To prevent combustion by-products, smoke or odors from entering the home and to improve efficiency, tape all duct joints securely. • Use only duct work deemed acceptable by state, municipal and local codes. • DO NOT install an additional in-line or external blower to increase the length of the duct run. Even small differences between blower air flow rates can greatly reduce the air draw of the hood.
WARNING • Observe all governing codes and ordinances during installation. Contact your local building department for further information. • A qualified technician must complete the installation of this built-in appliance. The owner is responsible to make sure the hood is properly installed. • Do not install the range hood unless the power supply provided meets the required Electrical (see page 3).
Installing the Mounting Bracket (Continued) 3. Height of mounting bracket (step 2) step 2. , Drill three appropriate sized pilot holes for the mounting hardware being used. The drywall mounting hardware must be purchased separately. Locate the vertical center line for the hood mounting location on the wall. Mark the center line with a six inch vertical line that intersects the line drawn in 4.
Hanging the Range Hood 1. , Attach the hood junction box to the top of the hood using two machine screws as shown. On models with two blowers: Put the exhaust cowling over the blower outlets on the top of the hood. Fasten the cowling in place with 14 machine screws. ,, ,T II II _I II , I_ , ', , I_ I I_ I iI II iI II iI II iI II iI II II II II II II ii II II ii II II ii II II ii II II ii II II , , Remove the filter(s) to reduce weight and avoid damage.
Connecting the Duct Work Final Chimney Assembly WARNING Do not use screws to attach the duct Work to the hood exhaust outlet, Use duct tape only. Screws may prevent the damper flaps on the top of the hood from opening. WARNING Be careful not to pinch the electrical wires While assembling the chimney. 1, Install the duct work between the hood exhaust and the I_p.mnvp.the. nrntp.ntivp, nl_£tin nnvp.rinn frnm hnth pieces of the chimney assembly.
Carefully put the chimney over the top of the duct 4. work Installation Checklist extending out of the top of the hood, taking care not to scratch the surfaces. Make sure the wiring is tucked in behind the chimney. WARNING Move the chimney up toward the ceiling. Line up the holes on the side of the chimney, above the vents, with the holes on the side of the chimney mounting bracket.
@ YELLOW/GREE_ t h ¢ O I ol 120V 60Hz t TO BLOWER MOTOR -, ® © F- CN1 CN2 z © ¢.D CN3 )OO¢ CN4 0 CN1 CN5 MAIN POWER SWITCH CN6 CN5 TRANSFORMER / LIGHT FIXTURES CONNECTION EXTERNAL BLOWER Please note--the layout on the PC Board shown above may vary-however all wires are coded and the connections on the PC Board are also coded with the same number/letters.
120V 60Hz O @ t TO BLOWER MOTOR @ YELLOW/GREEN MAIN POWER SWITCH t TO BLOWER MOTOR -rl CN3 _ E2 ) ( CN5 CN9 CN4 t 20V t CN1 E EE3- CN6 CN7 I---'1 CN9 _ TRANSFORMER 0 g TRANSFORMER _ 8z LIGHT FIXTURES !i J r--m CN3 O / CN 1 / CN2 CN 1 CN2 EXTERNALBLOWER CONNECTION Please note--the layout on the PC Board shown above may vary-however all wires are coded and the connections on the PC Board are also coded with the same number/letters.
12 ctmcor
The Life of the Kitchen? Dacor • 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 • Phone: (800) 793-0093 • Fax: (626)403-3130 • www.Dacor.