Installation Distinctive T_ Built-in Model DDW24S Pa_ No. I05658 Rev.
Important Safety Instructions ......................... About Safety Instructions ................................ Safety Symbols and Labels ............................ General Safety Precautions ............................ Product Specifications .................................... Product Dimensions ........................................ Preparing for Installation ................................. Electrical Specifications .................................. Water Supply Specifications ................
Important Information About Safety • The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution Instructions when installing, maintaining any other appliance. • or operating Safety Symbols and Labels I Immediate hazards WILL resUlt i n [_ that DANGER personal injury or death.
General Safety Precautions WARNING - To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING • Use this dishwasher 0nly for its intended purp0se as outlined in the use and care manual. It is not intended for commercial WARNING Usel • Do not tamperwith • This appliance is designed for installation by more than one person.
Product Dimensions Product tolerances: +1/16" (+1.6 mm) Depth with door open 49 3/4" (126.4 cm) ,_ 24" (61.0 I cm)-_ I -_ IP Depth with door closed 22 7/8" (63.2 cm) -_1 !_ "--- Drain hose Do not modify 34 3/8"* (87.4 cm) to 36 1/2" Front Depth dimensions allow for hose on back of unit Side (92.7 cm) --5 3/8" (13.7 cm) t _.7 3/8" (18.7 cm) ,r -- m _- 2" (50.0 cm) * Minimum height may be reduced by up to 1/2" (1.3 cm). See page 5. Shipping weight: 117 Ibs.
Observe all governing codes and ordinances during an(] installati0n: WARNING C0atact YOur !0ca I building department for further information. I planning Electrical SpeciFications WARNING Electrical and grounding connections mus t comply with the applicable portions of the national electrical code and/or other local electrical codes. .... This dishwasher comes with an electrical a three prong grounding plug for a 120 Vac, 15 Amp. power supply.
Cutout tolerances: Preparing the Location _Z +1/16" (+1.6 mm),-0 _ _ WARNING Follow all cabinet dimensions shown to insUre safe operation _All minimum product dimensions must be met or exceeded (see page 3)! Dimensions shown provide the required clearances. • The cabinet must enclose the dishwasher top, back and both sides. on the • Carefully check the location where the dishwasher is to be installed.
The drain hose is equipped with a cone-shaped connector on the end that is ready to be cut to the desired drain connection size. Only a clamp (not provided) is required. It fits drain connections with an internal diameter of 1/2, 5/8, 3/4 and 7/8 inches (1.3, 1.6, 1.8 and 2.2 cm). Preparing the Drain CAUTION Keep the factory installed high loop drain hose in place to ensure proper dishwasher 0peration_ Do not modify or move the mounting bracket in any manner.
Verify the Package Contents • Remove all styrofoam and plastic wrap from the dishwasher. Be sure to remove the toe kick from the top of the dishwasher packaging. With the assistance of at least one person, remove the dishwasher from the shipping pallet. Place the unit to the side of the cabinet opening. NOTE: Since each dishwasher is tested at the factory for proper operation, there may be some residual water inside the unit, the water supply line or drain hose.
. Installation Preparation WARNING • Before working on wiring for any electrical appliance, be sure the power has been turned off at the breaker/fuse box. Place a tag at the disconnect switch indicating you are working on the circuit. To make larger tension adjustments to the door springs, remove the back of the springs from the dishwasher by turning them outwards. Move them one hole farther back or forward, then make small adjustments as outlined in step 3 as necessary.
Level the Dishwasher 4. floor is level left to right using a level. Adjust the front legs as necessary. CAUTION ' A level unit is Very important to proper operati0n; Be sure to level the unit front to back and side to sidel , Open the door and pull the bottom rack out of the dishwasher. Check to make sure the dishwasher 5. Adjust the rear leg until the floor of the dishwasher is level front to back. Use caution when sliding the dishwasher On the floor.
Connecting (Permanently 4. the Wiring Connected (cont.) Appliance Installing the Unit in the Cabinet Only) If a nonmetallic cable is being used, install a UL listed strain relief bushing on the back of the dishwasher. 5. Connect the white wire on the cable to the "N" terminal on the dishwasher terminal block as shown below. 6. Connect the black wire on the cable to the "L" terminal on the terminal block. . 1. box _IK/ I_ '1 h in front of the cabinet opening. 2.
4. Once sure water sure the dishwasher is in place check to make all slack is pulled out of the power cable, supply line and drain hose. Check to make none of them are pinched or kinked. NOTE: Do not attach the mounting Verifying Operation. Water screws until after , Connect the drain hose to the air gap or directly to the waste tee or disposer above the sink trap as shown in one of the examples on page 6. 4. Tighten the holding clamp. 5.
. Check for leaks under the dishwasher and under the sink. If any leaks are found, immediately push the STOP button and disconnect power. If there are leaks under the sink, check the water supply and drain connections. Reconnect power and restart the cycle. If the leak is elsewhere, and a hose extension is installed, check for a loose connection. . Final Leveling 1. Check to make sure that adjacent drawers and cupboards can be opened when the dishwasher door is open.
Attaching the Anti-tip Brackets Installing the Toe Kick 1. I Make sure to anchor one antbtiP braCket On each CAUTION s de of the d shwasher. ........... 1. The anti-tip brackets protect against possible tipping caused by heavy bottom rack loads on the door. Use only the stainless steel screws provided with the machine. 2. Open the door rack out. Turn rack mounting toward you to and remove the top rack. Pull the both rack stops outwards on the rails (see diagram). Pull the rack remove.
Installation Checklist [_ WARNING * To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked and the unit is working properly. o Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor dishwasher cannot be overemphasized.
_acor 15
16 da=::ar.
Item No., 80 933 81 Rev. 03 The Life of the Kitchen? Dacor • 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 • Phone: (800) 793-0093 • Fax: (626)403-3130 • www.dacor.
