Installation Instructions 30 - Inch Dishwasher For use with models: ED30 and ID30 Part No. 65538 Rev.
Table of Contents Important Safety Instructions........................................... 1 Important Information About Safety Instructions............... 1 Safety Symbols and Labels.............................................. 1 General Safety Precautions.............................................. 2 Product Specifications...................................................... 3 Preparing for Installation................................................... 4 Preparing the Location........................
Important Safety Instructions Important Information About Safety Instructions • • Safety Symbols and Labels The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: Warning • Do not install or operate this dishwasher if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder.
Product Specifications Tolerances: +1/16”, -0, (+1.6 mm, -0) unless otherwise stated Dimensions Model ED30 shown. Door style varies with model number.
Preparing for Installation IMPORTANT: Follow all cabinet and countertop minimum dimensions shown below to insure safe operation. warning Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Prepare the installation location as shown below. All minimum product dimensions be must met or exceeded (see page 3). Dimensions shown provide minimum clearances, unless otherwise noted.
Preparing for Installation Electrical Specifications warning • The electrical outlet for the dishwasher should be installed only by a licensed electrician. • This appliance is equipped with a three prong grounding plug for your protection against possible electric shock hazards. If only a two prong outlet is available, it is the customer’s responsibility to have it replaced with a dedicated, grounded three prong electrical outlet by a licensed electrician.
Installation Instructions Verify the Package Contents A NOTE: Model ID30 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. • Remove all of the packing materials from inside and outside of the unit.
Installation Instructions warning Installing the Unit in the Cabinet • Do not connect the electrical, water inlet or drain until instructed to do so in the Verifying Proper Operation section. Care should be exercised when the appliance is installed or removed, to reduce the likelihood of damage to the power cord or hoses. • Do not install the dishwasher unless the electrical service provided meets the Electrical Specifications. 1.
Installation Instructions Leveling the Dishwasher (Continued) 3. Remove the toe kick mounting plate to expose the front legs. To adjust the front leveling legs, place a wrench on the top of each leg and adjust where the top of the dishwasher tank front trim is flush with the lower edge of the countertop. Attaching the Anti-Tip Brackets caution • Toe kick mounting plate (pull out to remove) Front leg 4.
Installation Instructions Cabinet Panel Installation (Model ID30 Only) 1/2” (13 mm) CAUTION • To prevent corrosion and the possibility of the panel falling off, use only stainless steel screws to attach. • The provided mounting screws are designed for panels with a thickness of 5/8” to 3/4”. Smaller panels may require different mounting hardware to prevent damage to the outside surface.
Installation Instructions Plumbing Connections 1. Connect the water supply hose from the dishwasher to the hot water supply valve. warning • For proper dishwasher operation and drainage, the drain line must be routed through the bottom of the cabinet and up to the drain or air gap connection. The drain hose or air gap outlet must connect above the sink trap. • If used, an air gap must be installed at countertop level. 2.
Installation Instructions Verifying Proper Operation □□ You should hear the dishwasher drain and then begin to fill with water. Wait approximately two (2) minutes, then carefully open the door to verify water is filling the dishwasher tank. If there is water present, close the door and continue the process. Should the water not fill the tank or the pump is not running, immediately push the START/STOP button to stop the dishwasher.
Installation Instructions Toe Kick Installation Adjusting and Installing the Included Toe Kick The the height and depth of the included toe kick are adjustable. 1. Adjust the toe kick height. The typical toe kick height is 4” high. For other than a typical installations, remove the rear assembly screws that hold the two toe kick sections together. Adjust the toe kick sections to match your desired toe kick height and reinstall the assembly screws. 2. Snap the toe kick into the toe kick mounting plate. 3.
Dacor ● Phone: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.
