Installation Instructions Downdraft Raised Vent Models: RV30, RV36, RV46 Includes installation instructions for optional cabinet blower (Dacor model CABP3) Use these downdraft raised vents only with approved Dacor ® cooktops. See the installation instructions for the particular cooktop model being installed to determine suitability. Part No. 85515 Rev.
Table of Contents Important Safety Instructions........................................... 1 Important Information About Safety Instructions............... 1 Safety Symbols and Labels.............................................. 1 General Safety Precautions.............................................. 2 Product Specifications...................................................... 3 Product Dimensions.......................................................... 3 Installation Specifications....................
Important Safety Instructions Important Information About Safety Instructions • • The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information on page 2.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: Warning • warning Do not install or operate a damaged appliance. If you receive a damaged appliance, contact your dealer or builder. Do not install or operate this unit if it has been damaged, dropped, has damaged electrical wiring or is not working properly.
Product Specifications Product Dimensions Tolerances: ±1/16” (±1.
Installation Specifications Electrical Specifications Planning the Installation General System Layout warning The electric service for the raised vent should be installed only by a licensed electrician. It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician.
Installation Specifications • • The raised vent exhaust may be configured to vent through the bottom or through one of the sides. Allow room for the exhaust duct coming out of the unit. See Planning the Duct Work (page 7) for additional details. Raised vent with cabinet blower mounted to front 90° elbow The maximum allowable duct run must be taken into consideration when determining the layout. See Planning the Duct Work for further details.
Installation Specifications General System Layout (Continued) Cabinet back Outside wall Cooktop Raised vent Raised vent configured for bottom exhaust Wall cap on outside wall 3 1/4” X 10” to round transition Duct work Wiring/conduit from raised vent to in-line blower Floor Duct work ILHSF series in-line blower Example of Layout with In-line Blower, Duct Work Under Floor, Wall Exhaust 6
Installation Specifications Planning the Duct Work warning • To reduce the risk of fire and to properly exhaust air, be sure to duct air outside the house or building. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages. • Tape all duct joints securely to prevent combustion by-products, smoke or odors from entering the home. Doing so will also improve system efficiency. • TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.
Installation Specifications Countertop 14 3/8" (365 mm) CL CL Duct connection center line A 1 7/8" * (48 mm) *Back of unit lines up with back of cutout Raised vent center line 1 7/8" * (48 mm) 25 5/8" (651 mm) 3 1/4 X 10 Duct connection Front View CL Front Exhaust Dimensions CABP3 Blower - Bottom Exhaust Bottom View Side Exhaust Locations (3 1/4” X 10”) Bottom Exhaust Location (3 1/4” X 10”) Vertical center line of bottom exhaust lines up with vertical Raised vent cen
Installation Specifications Calculating the Maximum Duct Run Length • Do not use duct work that is smaller in cross-sectional area than the required duct sizes in the table to the right. • For best performance, keep the duct run as short as possible and never exceed the maximums stated at the right. • The maximum straight duct length for the raised vent system depends on the model of blower used with the vent system and the number of elbows and transitions used.
Installation Instructions Parts List • • • • • • • • • • Product literature Vent cover Anchoring legs 2 wood screws, #14 x 2 1/2 (PN 83047) 3 wire nuts 2 sheet metal screws, #10 x 1/2 (PN 83022) 3 ¼” X 10 duct mounting flange 2 keps nuts, 1/4-20 (PN 83049) 2 flat washers, 1/4-20 (PN 83203) Insulation foam Installation Preparation warning • If the electrical service does not meet the Electrical Specifications on page 4, do not proceed with the installation.
Installation Instructions Installing the Vent in the Cutout ILHSF or REMP Series Blower Installation NOTE: The raised vent installs in the back of the cutout, separate from the cooktop. It is installed prior to final installation of the cooktop. Cabinet Blower Installation If using a ILHSF or REMP series blower, install it according to the blower installation instructions. Installing the Raised Vent If using cabinet blower (model CABP3): 1.
Installation Instructions Duct Work Installation • Install the duct work from the raised vent to the point where it exits the building according to the Installation Specifications. Use sheet metal screws and duct tape to connect and seal all of the pieces. Support the duct weight as necessary to ensure sealed joints. • On installations using a ILHSF or REMP series blower, run the three conductor wiring required to power the blower parallel to the duct work from the raised vent to the blower.
Installation Instructions Raised vent electrical connections see Wiring Diagram B Cabinet blower (CABP3) Blower electrical connections - see Wiring Diagram A Junction box Power supply wiring from junction to raised vent Power supply wiring from raised vent to CABP3 blower Electrical Wiring - Cabinet Blower Installations (CABP3) REMP series blower shown Connect wires/conduit according to remote or in-line blower installation instructions Raised vent electrical connections see Wiring Diagram B Junct
Installation Instructions Final Installation Installation Checklist Install the cooktop according to its installation instructions. Set the cooktop into the countertop opening so that the back edge of the cooktop overlaps the leading edge of the vent. Verifying Proper Operation In the interest of safety, perform the following checklist to make sure the unit has been properly installed. Proper installation is the responsibility of the consumer.
Technical Data RV Raised Vent Wiring Diagram BLOWR OUTPUT N2 L2 INCOMING 120V N1 L1 MOTOR DRIVE BLU BLK GRN/YEL CHASSIS GROUND STUD WHT L3 N3 BLK BLU WHT BLK NO COM NO FUSE 12A POWER CONTROL CIRCUIT BOARD COM LOWER LIMIT SWITCH COM UPPER LIMIT SWITCH UPPER LIMIT SWITCH RED LOWER LIMIT SWITCH TO PUSH BUTTON CIRCUIT BOARD L2 N2 BLOWER OUTPUT L1 N1 POWER INPUT GND GND GROUND CABP3 Cabinet Blower Ratings CABP3 Blower Performance Nominal 600 CFM Actual 585.
Notes 16
Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.Dacor.
