INSTRUCTION BOOK FOR ViewShare Tensioned Advantage Electrol Retrofit
Important Safety Instructions Pre-Installation When using your video equipment, basic safety precautions should always be followed, including the following: Prior to Retrofit installation, you will need to run a CAT5 or CAT5e network cable from the motor end of your screen to the area in which your computer will be located. THE CAT5 CABLE IS NOT PROVIDED. The length of the CAT5 cable cannot exceed 200 feet.
Removal of Old Screen and Roller Assembly 1. Run the screen to the up position. Access Door Screws 2. Remove the access door by removing the screws from each end (Figure 1). Be sure to support the door during this step to avoid injury. Lift the door slightly and pull away from the edge of the case. 3. Unplug 3 or 4 wire motor connector and RJ-22/45 cable (if applicable) from the junction box. See Appendix A for motor type details. 4. Remove retainer clip from the motor (Figure 2).
Pre-Installation of ViewShare Screen and Roller Assembly 1. Remove existing motor and pin end roller assembly brackets from inside the case. NOTE: At this point the inside of case will be empty except for the junction box connections on the motor end. Circular Knockouts for CAT5 Cable 2. Remove a single circular knockout from motor end of case for CAT5 cable needed in the Installation of ViewShare Screen and Roller Assembly (Figure 4).
Transfer of Existing Motor 1. Once the old screen and roller assembly is out of the case, remove the Phillips head screw securing the screen tensioning cable to the roller on the motor end (Figure 9). 2. Remove motor from the old screen and roller assembly and set aside (Figure 10). NOTE: Try to avoid turning the rubber collar on the motor as you are pulling the motor out of the roller as this will change the limit switch settings. 3. Remove the black L-bracket from pin end of roller (Figure 11). 4.
Transfer of Existing Motor (continued) 5. Completely remove both shipping brackets from the board. 6. Remove the three Phillips head screws from motor end bracket and remove wooden block (Figure 12). 7. On the ViewShare screen and roller assembly, loosen (but do not remove) the nut on the motor end arm bracket (Figure 13). 8. Remove the two end bracket bolts securing the motor end bracket to the shipping board. Slide the bracket away from the end while supporting the roller (Figure 13).
Transfer of Existing Motor (continued) 9. Carefully lift the roller above the mounting bracket and remove the Phillips head screw securing the tensioning cable to the roller (Figure 14). Motor Plug Tensioning Cable Screw 10. Remove the wood block and plug from the end of the roller (Figure 14). 11. Insert previously set aside motor into the ViewShare fabric and roller assembly.
Installation of ViewShare Screen and Roller Assembly NOTE: The ViewShare screen and roller assembly, which includes brackets and arms, must be installed as a complete unit. Do not attempt to disassemble these components during installation. 1. Shipping L-Bracket Remove two 1/4 – 20 nuts from pin end and motor end mounting brackets on the ViewShare screen and roller assembly shipping board (Figure 16). NOTE: If you transferred you existing motor, the motor end nuts have already been removed. 2.
Installation of ViewShare Screen and Roller Assembly (continued) 6. Remove black L-bracket on pin end of roller (Figure 18). NOTE: If you transferred your existing motor, this bracket was removed in the previous section. 7. Complete electrical hook-up by plugging in 3 or 4 wire motor connector and RJ-22/45 cable (if applicable) to the junction box. See Appendix A for motor type details. (Figure 19). Black L-Bracket 8. Carefully remove paper and tape from roller assembly.
Installation of ViewShare Screen and Roller Assembly (continued) 10. Remove the USB to CAT5 extender labeled “Remote” from the shipping carton. At the motor end of the case, attach the USB cable coming from the ViewShare screen and roller assembly. On the other end of the USB to CAT5 extender, attach the CAT5 cable that was run through the circular knockout. Remove the non-adhesive side of the tape and carefully allow the USB to CAT5 extender to hang freely (Figure 20).
Camera and Speakerphone Installation The following components are necessary and included for camera and speakerphone installation. • • • • Local CAT5 to USB Extender with Power Supply 6’ USB Cable USB Speakerphone Powered USB Hub with 3' USB Cable NOTE: A CAT5 cable is also required for installation. THE CAT5 CABLE IS NOT PROVIDED. The length of the CAT5 cable cannot exceed 200 feet.
Camera and Speakerphone Installation (continued) Camera and Speakerphone Setup Selection the Camera and Speakerphone You are now ready to run the initial camera setup. The computer will recognize the camera as a new component and load the appropriate drivers. This can take up to several minutes and you may need to follow on-screen instructions.
Troubleshooting Visit www.da-lite.com to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support. Symptom You can contact us by email at info@da-lite.com or by phone at 800.622.3737 or 574.267.8101 with any additional troubleshooting questions. Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker.
Appendix A: Screen Adjustment for Type 1 Motor (HV suffix in Part Number) TYPE 1 MOTOR 4-wire connection TYPE 1 WALL SWITCH Has manual limit adjustments on end of motor Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of screen, proceed in the following manner: Remove two screws to remove access door.
Appendix A: Screen Adjustment for Type 2 Motor (LT suffix in Part Number) TYPE 2 MOTOR TYPE 2 WALL SWITCH RJ-22 cable No manual limit adjustments on end of motor 3-wire connection 1. Remove the cover plate from the 3-button wall switch and remove the switch from the junction box. 2. Locate small 3-position switch on back of wall switch. 3. To adjust the down limit switch, slide the 3-position switch to the down position.
Appendix A: Screen Adjustment for Type 3 Motor (LS suffix in Part Number) TYPE 3 MOTOR TYPE 3 WALL SWITCH RJ-45 cable No manual limit adjustments on end of motor 3-wire connection 1. Locate the wall switch and remove the cover plate from the wall switch and remove the switch from the junction box. the up tactile button until the LED on back of switch blinks green twice. The up limit is now set. 2. Locate the two tactile buttons on the back of the switch.
Appendix B: Arm Adjustment 1. When screen is lowered approximately six inches below the case, the elbows of the arms should be horizontally aligned with each other (Figure 23) 2. If the arms are not horizontally aligned loosen (but do not remove) the adjustment nut found inside the case behind the screen and roller assembly (Figure 24). 3. With the adjustment nut loosened the arms can be adjusted inward and outward until horizontal alignment is correct. 4.
LIMITED WARRANTY – VIEWSHARE PRODUCTS Milestone AV Technologies LLC warrants its Da-Lite branded ViewShare products to the original purchaser only, to be free from defects in materials and workmanship in accordance with the following warranty term: A period of five (5) years for the Advantage screen and related components; and A period of three (3) years for the ViewShare camera and related components.
