INSTRUCTION BOOK FOR Multi Format Imager
Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using equipment. until it has been examined by a qualified service technician. 2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use. 5. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids. 3.
Multi Format Imager Assembly Frame Assembly: 1. In the hardware package, you will receive (12) #10 x .375" long button head screws and (8) #10 x .500" long button head screws required for frame assembly. 2. Lay frame pieces out on floor or table as shown in Figure 1. The right and left side frame assemblies have the rollers and motors attached to them. The bottom frame piece has (2) guide rails and the wiring junction box attached to it. The top frame piece will have the (2) guide rails attached to it.
Multi Format Imager Assembly 4. Fasten (3) #10 x .375" long button head screws through top of frame into the corner connector bracket. See Figure 5. Tighten two set screws on flat "L" bracket to line up the front faces as shown in Figure 6. Figure 4 Figure 5 Fasten Screws Through Top Frame Assembly Into Connecting Bracket Figure 6 Tighten Set Screws Until Front Surfaces Are Flush 5. Assemble bottom side of frame to left frame.
Multi Format Imager Assembly 7. Finish assembling corner assembly by inserting (3) #10 x .375" long button head screws through bottom of frame into the corner L connector bracket. Tighten two set screws on flat "L" bracket to line up the front faces as shown in Figure 10. Figure 10 Tighten Set Screws Until Front Surfaces Are Flush Fasten Screws Through Bottom Frame Assembly Into Connecting Bracket 8. Assemble right side of frame to top and bottom frame assemblies.
Multi Format Imager Assembly 9. Assemble top right and bottom right corner assembly by inserting (3) #10 x .375" long button head screws through bottom of frame into the corner L connector bracket. Tighten two set screws on flat "L" bracket to line up the front faces as shown in Figure 12.
Multi Format Imager Assembly 11. Untape black steel wire tension cable from bottom left side assembly. Un-wire tie the cable assembly. Run black steel wire tension cable down around pulley at end and bring back towards the end. You may have to pull slightly hard and clip the tension cable to the eyebolt secured in the slat bar as shown in Figure 14. Be careful not to pinch your fingers in the spring. Repeat this step for bottom right corner of screen.
Multi Format Imager Assembly 12. Assemble pinch guard bracket using (2) #10 x .375" long button head screws to opposite side of pulley bracket as shown in Figure 15. Repeat this step for bottom right corner of screen. Pinch Guard Bracket Fasten Screws Through Pinch Guard Bracket Into Pulley Bracket Figure 15 13. Untape black steel wire tension cable from top left side assembly. Un-wire tie the cable assembly. This cable assembly will have an extra safety wire ran through the spring.
Multi Format Imager Assembly 14. Assemble pinch guard bracket using (2) #10 X .375" long button head screws to opposite side of pulley bracket as shown in Figure 17. Repeat this step for top right corner of screen. Figure 17 Fasten Screws Through Pinch Guard Bracket Into Pulley Bracket Pinch Guard Bracket 15. Attach first side of safety cable to eyebolt in middle of screen. Attach other side of safety cable to the eyebolt in side of frame in front of wind up pulley.
Multi Format Imager Installation Wall Mounting Assembly: 1. Depending on size of screen it will be shipped with either 2 wall brackets that are 48" long or 2 wall brackets that are 64" long. Two small "L" brackets included will be used to hold frame securely to wall at bottom. 2. To install the Multi-Format Imager over a Da-Lite Perm-Wall screen you will need to place the supplied wooden spacers between the screen and the wall. Da-Snap, Imager and Cinema Contour frame do not require any spacers. 3.
Multi Format Imager Installation 6. Wall hanging brackets must be evenly spaced across top of frame. Measure the frame width and divide by three then make two marks from the end. The center of each wall bracket shall be located on those marks.
Multi Format Imager Installation 7. Hang the frame assembly on the hanger brackets as shown in Figure 22. Be careful as bracket is to slide in front of the aluminum guide channel. There is a lip on the back of the frame that wedges itself in to the hanger bracket once fully installed on bracket. This is a two person installation. Do not attempt to do this without two people.
Multi Format Imager Wiring Diagram 1. To connect power to unit locate junction box cover on bottom frame assembly. There will be two black screws holding the wiring box cover on as shown in Figure 25. Figure 25 Remove Two Screws Holding Junction Box Cover 2. Install electrical connections. Make sure to review the wiring diagram for proper hook up as shown in Figure 26.
Multi Format Imager Wiring Diagram 3. Connect IR eye to splitter for screen operation. IR eye shall be plugged into a QEYE port on the primary splitter as shown in Figure 27. 6P4C RJ-14 Cable Figure 27 RJ-22 +12V Primary Splitter IR EYE Green Bus (RP Data) Yellow RQ Data +5V Red Ground Black RQ Clock White RJ-14 QEYE Inputs 6P6C RJ-22 Cable From QAUX To QEYE Blue Bus (RP Data) White RQ Data Green +5V Secondary Splitter Ground Red Black NOTES: 1. 6P6C = 6 Pins 6 Conductor Wire 2.
Multi Format Imager Intermediate Stop Adjustment 1. To adjust intermediate stopping positions make sure both masks are completely retracted into the frame. Press the left mask ">" button. The mask will start to move outward. Press the stop button at the position you want it set to. If you go too far outward press the left mask "<" button and the mask will retract back into the case. 3. Once both masks are at the desired stopping position.
Multi Format Imager Limit Travel Adjustment 6. Locate the two tactile buttons on the back of the switch. They are square silver with black round buttons as shown in Figure 30. 7. To adjust how far the mask travels outward towards the middle of masking screen, press and hold the down tactile button until the LED on back of switch turns solid red. This will put the motor in limit set mode. Turn the wall switch over and use the down button on front of switch.
Troubleshooting Visit www.da-lite.com to find installation and troubleshooting videos and tutorials. You will also find a link to Live Chat for interactive support and you can contact us by email at info@da-lite.com or by phone at (800) 622-3737 or (574) 267-8101 with any troubleshooting questions. Symptom asking System will not operate. M Motor does not hum. Masking System does not stop at correct position. Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V).
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.
