INSTRUCTION BOOK FOR Large Advantage® Electrol®
Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 4.
Tools Required for Installation #2 Phillips Screwdriver 3/4“ Open Wrench or Socket Driver Pre-Installation 1. Carefully unpack case from shipping crate. 5. 2. Set aside the Installation Kit. Items inside will be used during installation. Ironing Board 3. Make sure to recheck measurement of case for proper installation clearance. 4. Remove any protective foam from case. If necessary. adjust hanger brackets with a 3/4" open wrench or socket driver.
Case Installation The case has a self-trimming flange around the bottom. Ceiling tiles or drywall may be placed on top of this flange to provide a finished appearance. 1. 2. The case provides multiple attachment points for bolts, cables, or threaded rod. Page 5 shows threaded rod installed. The variable position-mounting bracket may be located anywhere along the length of the case. It is recommended to keep the brackets spaced evenly enough to distribute the weight of the screen.
Installation 9 1/8" (Suggested) 1/2" Threaded Rod (Not Included) Attached to Mounting Bracket Electrical Junction Box 12 3/16" Screen Roller 11" Audience Side 11 7/16" Self-Trimming Flange Finished Ceiling Self-Trimming Flange 13 1/8" Access Door 2 3/16" 10 15/16" Variable Position Mounting Brackets Electrical Junction Box 5
Screen And Roller Assembly Installation Tools required for screen and roller assembly: 9/16“ Open Wrench or Socket Driver 1/2“ Open Wrench or Socket Driver 5/32“ Hex Key If your screen was shipped with the motor and roller already installed proceed to step 7. 1. Remove the access door. First, remove the 2 bolts from each end with a 9/16" open wrench or socket driver. Next, use a 5/32" hex key to remove the two screws in the center of the access door.
Screen Adjustment Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner: NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments. More Screen Drop 1. Place operating switch in “down” position. LVC Control Box 2. When the screen stops, turn the white “down” limit knob one-quarter turn counterclockwise (Figure 5).
120V Wiring Diagram NOTE: 20-24 AWG wire recommended for connecting wall switch to low voltage controller. CAUTION: Do not use 3-position high voltage rocker switch with this unit! This will damage the low voltage control board. ATTENTION: N'utilisez pas un interrupteur à bascule à 3 positions pour circuit à haute tension avec cette unité. Cela endommagera le tableau de contrôle basse tension.
240V Wiring Diagram NOTE: 20-24 AWG wire recommended for connecting wall switch to low voltage controller. CAUTION: Do not use 3-position high voltage rocker switch with this unit! This will damage the low voltage control board. ATTENTION: N'utilisez pas un interrupteur à bascule à 3 positions pour circuit à haute tension avec cette unité. Cela endommagera le tableau de contrôle basse tension.
Troubleshooting Visit www.da-lite.com to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support. Symptom You can contact us by email at info@da-lite.com or by phone at 800.622.3737 or 574.267.8101 with any additional troubleshooting questions. Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker.
LIMITED FIVE YEAR WARRANTY ON DA-LITE TENSIONED ADVANTAGE® ELECTROL®, ADVANTAGE® ELECTROL®, TENSIONED LARGE ADVANTAGE® ELECTROL®, LARGE ADVANTAGE® ELECTROL®, TENSIONED CONTOUR® ELECTROL® AND CONTOUR® ELECTROL® PRODUCTS ONLY Milestone AV Technologies LLC warrants these Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to
