INSTRUCTION BOOK FOR Large Advantage® Deluxe Electrol®
Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 6. 2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids. 7. To reduce the risk of electric shock, do not disassemble this appliance.
Tools Required for Installation #2 Phillips Screwdriver 3/4“ Open Wrench or Socket Driver Pre-Installation 1. Carefully unpack case from shipping crate. 5. 2. Set aside the Installation Kit. Items inside will be used during installation. Ironing Board 3. Make sure to recheck measurement of case for proper installation clearance. 4. Remove any protective foam from case. If necessary. adjust hanger brackets with a 3/4" open wrench or socket driver.
Case Installation The case has a self-trimming flange around the bottom. Ceiling tiles or drywall may be placed on top of this flange to provide a finished appearance. 1. 2. The case provides multiple attachment points for bolts, cables, or threaded rod. Page 5 shows threaded rod installed. The variable position-mounting bracket may be located anywhere along the length of the case. It is recommended to keep the brackets spaced evenly enough to distribute the weight of the screen.
Installation (Suggested) ½" Threaded Rod (Not Included) Attached To Mounting Bracket 9 1/8" Screen Roller Audience Side 12 3/16" 11 7/16" 11" Door Roller Finished Ceiling Self-Trimming Flange Self-Trimming Flange 2 5/16" 13 1/8" Access Door Closing Door 10 13/16" 11" Case Length Variable Position Mounting Brackets 8 ½" 11 ½" Electrical Junction Box 8 ½" 5
Screen And Roller Assembly Installation If your screen was shipped with the motor and roller already installed proceed to step 7. 1. Remove four bolts from ends of door assembly (2 bolts on each end) (Fig. 2). This will allow the door assembly to drop open for access to case. For larger sizes, you will also need to remove the door support screws. 2. Carefully unpack screen and roller assembly. Leave packing paper on the roller. 3. Remove the square peg bracket from the motor end of the roller assembly.
Screen Adjustment Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner: NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments. More Screen Drop 1. Place operating switch in “down” position. 2. When the screen stops, turn the white “down” limit knob (Fig. 3) one-quarter turn counterclockwise.
120V Wiring Diagram NOTE: 20-24 AWG wire recommended for connecting wall switch to dual motor controller. CAUTION: Do not use 3-position high voltage rocker switch with this unit! This will damage the low voltage control board. ATTENTION: N'utilisez pas un interrupteur à bascule à 3 positions pour circuit à haute tension avec cette unité. Cela endommagera le tableau de contrôle basse tension.
240V Wiring Diagram NOTE: 20-24 AWG wire recommended for connecting wall switch to dual motor controller. CAUTION: Do not use 3-position high voltage rocker switch with this unit! This will damage the low voltage control board. ATTENTION: N'utilisez pas un interrupteur à bascule à 3 positions pour circuit à haute tension avec cette unité. Cela endommagera le tableau de contrôle basse tension.
Troubleshooting Visit www.da-lite.com to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support. You can contact us by email at info@da-lite.com or by phone at 800.622.3737 or 574.267.8101 with any additional troubleshooting questions. Symptom Cause Solution Screen will not operate or will not go “down”. Motor does not hum. Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line.
Troubleshooting (continued) Symptom Cause Solution Spring has an obstruction not allowing door to open.. Check installation to free door. Clear any foreign substance from spring. No power. See above. Mis-adjusted door motor limit. Adjust door motor limit. Call Da-Lite for instruction. Low voltage board has no power or a blown transformer. Replace low voltage board. “Down” limit switch incorrect.. “Down” limit switch out of adjustment. See installation instructions. Noise.
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.
