INSTRUCTION BOOK FOR Tensioned Advantage® Electrol®
Important Safety Instructions Pre-Installation When using your video equipment, basic safety precautions should always be followed, including the following: 1. Carefully unpack case from shipping carton. 1. Read and understand all instructions before using. 2. Set aside the Installation Kit. Items inside will be used during installation. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3.
Screen And Roller Assembly Installation Tools required for screen and roller assembly: #2 Phillips Screwdriver 1/8“ Hex Key 1/2“ Open Wrench or Socket Driver 1/4“ Open Wrench or Socket Driver Follow these steps if your screen and roller assembly was ordered separately from the case. 1. Remove the access door. First, remove the 2 screws from the ends using a #2 phillips screwdriver. Be sure to support the door during this step to avoid injury.
Tensioned Advantage® Electrol® Suggested Methods of Installation Method 1 6 1/16" 6 7/16" 7 3/4" Variable Position Mounting Bracket 8" Audience Side Motor End 6 1/16" 3/8" Threaded Rod (Not Included) Attached To Mounting Bracket Electrical Junction Box 6 3/8" Self-Trimming Flange Finished Ceiling 7 3/4" Method 2 3/8" Threaded Rod (Not Supplied) Hanger Bracket 3 7/16" 7 7/16" 6 7/16" 7 3/4" 4
Screen Adjustment for 120V Screens If your Tensioned Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the 120V Wiring Diagram. 1. Locate the wall switch and remove the cover plate from the wall switch and remove the switch from the junction box. 2. Locate the two tactile buttons on the back of the switch.
Tensioned Advantage® Electrol® Installation for 120V Screens 120V Wiring Diagram UP IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible.. 3-conductor 20–24 gauge wire can be used in place of the supplied RJ-14 cable to connect the wall switch.
Tensioned Advantage® Electrol® Installation for 120V Screens 120V Wiring Diagram with Optional Built-In Video Projector Interface CAUTION: The projector must be turned off before connecting the trigger wires to the projector. Failure to do so may damage the controller. IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible.
Tensioned Advantage® Electrol® Installation for 220/240V Screens 240V Wiring Diagram ILT RJ-9 Pin-Outs (Tab Is Facing Up) IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is accessible.
Troubleshooting Visit www.da-lite.com to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support. Symptom You can contact us by email at info@da-lite.com or by phone at 800.622.3737 or 574.267.8101 with any additional troubleshooting questions. Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker.
LIMITED FIVE YEAR WARRANTY ON DA-LITE TENSIONED ADVANTAGE® ELECTROL®, ADVANTAGE® ELECTROL®, TENSIONED LARGE ADVANTAGE® ELECTROL®, LARGE ADVANTAGE® ELECTROL®, TENSIONED CONTOUR® ELECTROL® AND CONTOUR® ELECTROL® PRODUCTS ONLY Milestone AV Technologies LLC warrants these Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to
