The Da-Lite Difference. Instruction Book for Tensioned Advantage® Deluxe Electrol® DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www.da-lite.com e-mail: info@da-lite.
IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 4.
SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed proceed to step 6. 1. Remove the screw from each end of the access door (front door) and open the door. See figure 1. 2. Carefully unpack screen and roller assembly. Leave packing paper on the roller. 3. Place the roller assembly into the case with the motor on the left side. The limit switches should be facing down. Line up the square pin on the motor with the square hole in the bracket. 4.
TENSIONED ADVANTAGE® DELUXE ELECTROL® INSTRUCTIONS FOR STANDARD CONTROL 120V WIRING DIAGRAM FRONT OF WALL SWITCH BACK OF WALL SWITCH UP NOTE: 20-24AWG WIRE RECOMMENDED FOR CONNECTING WALL SWITCH TO THE DUAL MOTOR CONTROLLER STOP DOWN NOTE: Electrical connections on left end of case.
TENSIONED ADVANTAGE® DELUXE ELECTROL® INSTRUCTIONS SCB-100 CONTROL NOTE: Electrical connections on right side of case. POWER INPUT AND CONTROL BOARD ARE LOCATED ON RIGHT SIDE OF SCREEN HOUSING.
TENSIONED ADVANTAGE® DELUXE ELECTROL® INSTRUCTIONS SCB-200 CONTROL NOTE: Electrical connections on right side of case. POWER INPUT AND CONTROL BOARD ARE LOCATED ON RIGHT SIDE OF SCREEN HOUSING.
TENSIONED ADVANTAGE® DELUXE ELECTROL® INSTALLATION 7-1/4" VARIABLE POSITION CASE LENGTH MOUNTING BRACKETS 7-1/4" 7-5/8" Flat bracket Mounting Method MOTOR END 9-1/4" ELECTRICAL JUNCTION BOX 7-5/8" (SUGGESTED) 3/8" THREADED ROD (NOT INCLUDED) ATTACHED TO MOUNTING BRACKET 7-1/4" FINISHED CEILING SELF-TRIMMING FLANGE 8-3/4" SEE DETAIL A formed bracket Mounting Method 4.59" (SUGGESTED) 3/8" THREADED ROD (NOT INCLUDED) 7.21" HANGER BRACKET 8.75" DETAIL A 6 8.
TROUBLESHOOTING Visit www.da-lite.com/products/tutorials.php to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support and you can contact us by email at info@da-lite.com or by phone at (800) 622-3737 or (574) 267-8101 with any troubleshooting questions. Symptom Cause Solution (a) Incorrect line voltage. (b) Blown facility fuse. (a) Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line.
TROUBLESHOOTING Symptom Cause Solution 3. Door will not open. (a) Hinge is bound or has a foreign substance on it which does not allow it to open by gravity. (a) Check installation to free door. Clear any foreign substance; i.e., paint or plaster from hinge. (b) No power. (b) See above. (a) Open door limit switch. (a) Replace switch. (b) No power from screen motor. (b) Replace screen motor. 4. Door does not close. 5. “Down” limit switch incorrect.
9
10
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are properly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.
